PYLE Audio PBMSPG80 User manual

Party Blaster Boombox
User Manual
PBMSPG80

1
LOCATION OF CONTROLS

2
Main Unit
1. BASS CONTROL
2. CD DOOR
3. CD DOOR KNOB
4. VOLUME+/-
5. STANDBY/ON
6. FOLDER-
7. LIGHT
8. EQ
9. FOLDER+
10. FUCTION
11. REPEAT
12. STOP
13. PLAY/PAUSE
14. USB CONNECTION
15. AUX-IN JACK
16. NFC AREA
17. SD CARD SLOT
18. PROG.
19.
20.
21. DC IN JACK
22. POWER ON/OFF SWICH
23. BATTERY COMPARTMENT
Remote Control
1. STANDBY/ON
2. MUTE
3. CD/USB/SD MODE
4. FM MODE
5. AUX-IN/BT
6. FOLDER-
7. FOLDER+
8. PROG.
9. PRESENT
10. REAPEAT/INTRO
11. RANDOM
12. EQ
13. ID3
14.
15. PLAY/PAUSE
16.
17. VOLUME+/-
18. FM MONO/STOP

3
INSTRUCTIONS FOR ATTACHING THE STRAP
1. Press the buckle and fix them in position „A‟and „B‟(see below diagram).
2. The length of the strap can be adjusted on the strap.

4
OPERATING INSTRUCTIONS
POWER SOURCE
1. Connect the AC adaptor to the DC IN jack on the back of of the unit firmly, and plug
it into a wall outlet.
2. Slide the power switch on the back of the unit to “ON”positon, the unit is in standby
mode, and display shows “--:--” with flashing digits.
3. You can now press the button on unit or remote control to turn on the unit. The
display shows “HELLO”. Press the button on unit or remote control to turn off the
unit, then the display shows “GOOD--BYE”.
4. Slide the power switch on the back of the unit to “OFF”positon, and pull the AC
adaptor out of the wall outlet if you want to switch off completely.
CLOCK SETTING
During in the STANDBY mode:
1. Press and hold PROG. button on unit or remote control until the time displays 24-
hour digit flashing.
2. Press or button to adjust 12-hour or 24-hour digit.
3. Press PROG. button again, the time display HOUR digit flashes, press the or 
button to adjust HOUR digit. Press PROG. button once more, the MINUTE digit
flashes, adjust it by the or button.
4. Press PROG. button again to confirm the time.
5. Each enable state as shown above will be cleared if the key is not pushed in 10
seconds.
RADIO OPERATION
TUNNING
1. Press STANDBY/ON button on the unit or remote control to turn on the unit and
press the FUNCTION button on the unit or FM button on remote control to select the
TUNER mode.
2. Press or button will change the frequency by 0.05MHz.
3. Press or button for approx. 1 second to active automatic tuning. Automatic
tuning stops when the first station with a sufficiently strong signal has been found.
The display shows STEREO when a stereo signal is beiing received.
MONO/ STEREO SELECT
This unit can receive the FM mode only. When you press FM MONO/STOP button on
remote control, the FM STEREO indicator will turn off & switch to MONO FM status.
STATION MEMORY
You can also preset stations of your choice and store up 20 FM stations in its memory.
1. Tune to the required station.
2. Press PROG. button on unit or remote. The station
number flashes in the display.
3. Press or button for your desired station number.
4. Press PROG. button to store the station.
5. Repeat steps 1 to 4 to store more stations or change previously stored stations.

5
OPERATING INSTRUCTIONS
SELECTING THE PRESET STATIONS
Press PRESET button on remote to select the desired preset station number.
BLUETOOTH FUNCTION
Paring the unit and the Bluetooth device (such as: mobile phones, tablet, PCs, etc.).
PAIR THE UNIT USING NFC
1. Press the FUNCTION button on unit or AUX/BT button on remote control to select
the BT mode.
2. With Near Field Communication (NFC), you can easily pair and connect the unit to
Android device with NFC.
3. If the Android device supports NFC, activate its NFC feature, and touch the NFC
area of the unit with the NFC area of your Android device. The unit connects to the
device automatically. For details on NFC, see the user guide of the Android device.
4. For other Bluetooth device, pair the unit manually.
PAIR THE UNIT MANUALLY
1. Verify that the Bluetooth function of Bluetooth device is enabled.
2. Press the FUNCTION button on unit or AUX/BT button on remote control to select
the BT mode.
3. The unit is now in pairing mode, it will last for 30 seconds.
4. Choose the Bluetooth menu in your Bluetooth device, and from the found devices,
select the “PBMSPG80”. If you are prompted to enter the PIN code, please enter
"0000"(four zeros).
5. For more information, see the user manual of Bluetooth device.
6. After a successful pairing, play the music from the Bluetooth device.
Note:
1. Only one Bluetooth device can be connected to the unit. If the unit is already
connected to another Bluetooth device, the unit will not appear in the Bluetooth
menu of your Bluetooth device.

6
OPERATING INSTRUCTIONS
2. When you turn off/on the unit or the Bluetooth device, the unit will connect to the
Bluetooth device automatically within 30 seconds. Otherwise, you need to connect it
manually on the Bluetooth menu in your Bluetooth device.
3. Depending on the device manufacturer, some Bluetooth devices need to perform the
pairing again.
LISTENING TO CD or MP3 DISC
1. Press FUNCTION button on the unit or CD/USB/SD button on remote control to
select the CD mode.
2. Place the CD/MP3 disc into the disc tray, then close and lock the CD door. The unit
will read the CD/MP3 disc automatically.
3. Press the VOLUME + or - button on unit or remote control to adjust the volume.
AUDIO CD PLAYBACK
1. When the disc tray is closed and a CD is inside, the total
number of the tracks and playing time appear in the display
and the first track will play automatically. The CD indicator
will always show on the display when the unit is in CD
mode.
2. If there has no disc inside, the display will show “NO DISC”
and remain in stop mode.
3. If the disc tray is not closed, the display will show “OPEN”.
AUDIO MP3 PLAYBACK
1. When the disc tray is closed and a MP3 playback disc is
inside, the total number of the folders and tracks in the disc
show on the display and the first track will play
automatically. The current folder number always show on
the display when the unit is in MP3 mode.
2. If there has no disc inside, the display will show “NO DISC”
and remain in stop mode.
3. If the disc tray is not closed, the display will show “OPEN”.
4. Press ID3 button on remote control once. The display will show “ID3 ON”, and then it
will automatically search more than 64 letters of “TITLE NAME”, “ARTIST NAME”
which move from the right corner to the left coner on the display continuously.
5. Press ID3 button once again, the display will shows “ID3 OFF”, and then the unit will
play normaly.

7
OPERATING INSTRUCTIONS
PLAY/PAUSE MODE
1. When the PLAY/PAUSE button is pressed during CD/MP3 stop mode, the first track
will play. The track number and elapsed track playing time appear in the display.
2. For interruption while the CD/MP3 playback disc is playing, press the PLAY/PAUSE
button once. Playback is now paused, the elapsed track playing time will stop.
3. Though the sound stops, the disc will continue to spin. To re-start playback, press
the PLAY/PAUSE buton again. The music will start from the exact position where it
was interrupted.
4. To stop the CD/MP3 playback, press the STOP button once in Play or Pause mode.
5. Press STANYBY buton on the unit or remote control to turn off the unit.
SKIP and SEARCH MODE
1. In play or pause mode, when or button is pressed once, the player will
advance to the next track or return to the beginning of the track.
2. During play mode, when or button is pressed and held, it will search the track
with audible high-speed forward or backward playback.
FOLDER MODE(MP3 only)
In play or stop mode, press FOLDER(+ or -) button on remote control, the folder will
advance to the next or return to previous folder.
REPEAT (CD)
1. Repeat One:
When the CD play mode, press the REPEAT button once,
the REPEAT indicator will show on the display. This single
track of music will be repeated.
2. Repeat All:
When the CD play mode, press REPEAT button twice, the
REPEAT ALL indicator show on the display. The whole
disc will be played continuously.
3. To cancel the function
Press the REPEAT button repeatedly until no indicator
appears on the display, and standard playback resumes.

8
REPEAT MODE (MP3)
1. Repeat One:
When the MP3 play mode, press the REPEAT button once,
the REPEAT indicator show on the display. This single
track of music will be repeated.
2. Repeat Album:
When the MP3 play mode, press the REPEAT button twice,
the REPEAT ALBUM indicator show on the DISPLAY. The
whole folder of the MP3 music will be played continuously.
3. Repeat ALL:
When the MP3 play mode, press REPEAT button third time,
the REPEAT ALL indicator show on the display. The whole
disc will be played continuously.
4. To cancel the function
Press the REPEAT button repeatedly until no indicator
appears on the display, and standard playback resumes.
RANDOM PLAY MODE
This feature allows the track on the disc to be played in random order.
1. Press RANDOM button on remote control. The RANDOM
indicator will show on the display and all music will play in
random order.
2. To cancel the Random play function, press the RANDOM
button again. The RANDOM indicator will disappear from
the display.
PROGRAM MODE
1. During the stop mode, press PROG. button on unit or
remote control once. The total number of track will blink
continuously and the number of Program to be memorized
starts from the first program “PR:01”on the display.
2. Press or button to your desired musical track, the
display will show the appropriate track number. Press the
PROG. button again to store this track in memory.
OPERATING INSTRUCTIONS

9
3. Repeat above procedure until all desired tracks have been
programmed.
4. For CD playback, a total of 20 tracks can be stored in memory. For MP3 playback, a
total of 99 tracks can be stored in memory.
5. Press the PLAY/PAUSE button once to start the program playback.
6. To check the program you have stored after complete programming press the PROG.
button once, the display will show the first programmed track number. Repeat above
procedure to read all the programmed memory.
7. To cancel the programmed memory:
During the stop mode, press the STOP button once, or
Open the disc tray during the stop mode.
The Program Indicator will disappear from the display.
MP3 PLAYBACK VIA USB PORT OR SD CARD READER
1. Insert a USB drive or SD card, and press FUNCTION button on the unit or
CD/USB/SD button on remote control to select the USB or SD mode.
3. The USB or SD shows in the LCD and after the USB drive or SD card is successfully
detected and read, the track number as a total shows in the LCD.
4. All functions are operated same as MP3 playback.
PARTY LIGHT
The party light effect pluse to music. Press LIGHT button on the unit, the colour of party
light effect changes as below:
EQ CONTROL
Press the EQ button, the sound tone changes as below:
BASS BOOST FUNCTION
Turn the BASS BOOST control up or down on unit to enhance the bass effect.
OPERATING INSTRUCTIONS