Pyle PT560AU User manual

300 Watts DigitalAM/FM Stereo Receiver
www.pyleaudio.com

PT560AU Foreword -Features
Foreword
Thank you for purchasing this fine PYLE PRO amplifier.
Please
read this operating instruction carefully before using. It will acquaint you fully
with
all its features and help you enjoy your time.
The product adopts the most advanced digital technique in the world. It is 4 channels
with high power output,
so to speak, the real acoustic centre ofyour family movie
theatre.
Features
• Stereo Amplifier With AlB Speaker Output
• AM/FM Radio With Digital Display Screen
• Auto Scan, Memory, Radio Station PREVIOUS/NEXT control
• Remote Control Included
• 50 Radio Station Pre-Set Memory
• Volume/Balance/TREBLE/BASS Gain Control For Main Channel
• VOLUME/BASS/TREBLE/ECHO Control For Microphone
• Two Microphone I nput Jacks
• Three RCA Input Source
• 11 0/220V power switch
• AM/FM Antenna Included
• USB For Mp3 Player

PT560AU Precautions
Precautions
1. Power source-The unit should be connected to a power supply AC-11 OV/60Hz or
AC-220V/SOHz.
2.Ventilation- The unit should be situated so that its location or position does not
interfere with its proper ventilation. Place the unit at least 1 Ocm away from the
walls.
3. Water and moisture-The unit should not be used near water-for example, near a
swimming pool in a wet basement, etc.
4.
Electric shock-if a metal object, such as hair pin or needle comes into contact inside
this unit, a dangerous electric shock may result. For families with children, never
permit children to put anything, especially metal, inside this unit.
5. Enclosure removal-Never remove the enclosure. If the internal parts are touched
accidentally, a serious electric shock might occur.
6.Abnormal smell-if an abnormal smell or smoke is detected, immediately turn the
power OFF and pullout the power cord. Contact your dealer or nearest service
station.
2

PT560AU Technical Specifications
Technical Specifications
Technical PT560AU
Main Channel Power Output
PMPO, 4 Ohms, 1KHz test 300WX2
THO(1KHz) <1%
Normal Load Impedance 8 Ohm
Input Sensitivity
CO/OVO AUXlUSB 300mV/33k Ohm
Impedance
Microphone
6mV/600 Ohm
Pure Amplifier >76dB
Signal to Noise Ratio KARAOKE >71dB
Frequency Range
Frequency Response(40Hz-15KHz) ±2dB
Tone Characteristic(1OOHz-10KHz) ±14dB
Power Requirements AC-11
OV 160Hz AC-220V50Hz
Dimension
19 "(W) x11.4"(O)x 4.7" (H) inch
Weight 11.51bs
* Specifications subject to change without prior notice

__ PT560AU Front panel
19
~':l>PYLE "
PRe)
300 WATTS DIGITAL AM/H.I STEREO RECEIVER PT560AU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
1. POWER SWITCH
Press
to switch the power unit ON or OFF.
2. MIC BASS
Adjusts the bass of M IC.
3. MIC TREBLE
Adjusts the treble of M
IC.
4. ECHO CONTROL
Turn the knob to adjust the
MIC echo level.
5. MIC INPUT JACK 1
KARAOKE
MIC connect to this jack.
6. PLAY / PAUSE
USB play/pause
7. PREV<
When it is TUNER , it means the preview
station;When it is USB ,it means the
preview song.
8.NEXT >
When it is TUNER , it means the next
station; When it is USB ,it means the
next song.
9. AM / FM SELECTOR
10. AUTO
Automatically search the signal of tuner.
11.TUNING
Press this key and turn the main volume
control (18) to adjust the tuning.
12. INPUT
This is used to select the input sources:
DVDI CD, AU X/USB, I POD 1M P3, TUN ER,
13. MIC INPUT JACK 2
KARAOKE MIC connect to this jack.
14. MIC VOLUME
Adjusts the volume level. Turn the knob
clockwise to increase the MIC volume.
15. BALANCE CONTROL
Turn the knob to adjust the master balance level.
16. TREBLE CONTROL
Turn the knob to adjust the master treble level.
17. BASS CONTROL
Turn the knob to adjust the master bass level.
18. MASTER VOLUME CONTROL
Adjusts the volume level. Turn the knob.
clockwise to increase the volume.
19. USB JACK
4

I~~~~I
~F.eA NTEN NA s AM e
2
1. TUNERANT
ENGINI:IERI:D IN .JAPAN
D Esnli N ED I N T H E US A
l ~ t ~~ ~ 1
,..'''.""'.. '''.''' ""''' ~ '' ''
Connect for AM and FM antennas.
2. AUDIO INPUT JACKS
3
Connect the audio output jacks of
IPOO/MP3 CO/OVOto these jacks.
3. ASPEAKER OUTPUTTERMINALS
Connect your speaker system to
these terminals.
4. B SPEAKER OUTPUTTERMINALS
4
Connect your the other speaker system(s) to
these terminals.
5. Fan
Cooling Speed Fan
6. 11 OV / 220V SWITCH
According to power voltage , push this button
to the station of the11 OV or 220V.
7. POWER CORD
Connect to AC 11 OV/60Hz&220V/50Hz outlet.
5
PT560AU Rear panel
VO LT AGE SELE CT OR
5 6 7

PT560AU Remote
2
3
4
5
6
7
15
14
13
12
11
10
9
8
@"'5>PYLE"
PRO
PT560AU
AMPLIFIERREMOTE
Remote Control Operation
1. Signal input selector
DVD /CD, AUX / USB , IPOD / MP3 , TUNER selector
2. Number buttons
Using for st SELECT & STORE
3. MEMORY
After a station has been found, you can store the station
by pressing the MEMORY button.
4.AUTO SCAN
AM /FM auto scan selector , scan and store stations
automatically. Can store 50 stations.
5. ST / MONO
Stereo and mono selector.
6.AM /FM
AM /FM selector.
7/10. DISP- / DISP+
Display Down And Up
8/11.
VOL- / VOL+
Master Volume Down And Up
9. MUTE
Mute Selector
12. TUNING ... TUNING"Y
The two keys are used to adjust to the best signal of
the stations.
13. USB Play Next
14. USB Play Prey
15.
USB Play / Pause
1. Remote control should be operated within 6
meters and the scope
of 30· in front of receiver.
2. Make sure that there is no big obstacle between
remote control and machine.
3. Remote sensor should be far away
from the light,high amounts
of light can affect its performance.
6

PT560AU Rear Panel Connecting
Connecting to amplifier
AM ANTENNA
FAN HEAT EXHAUST SYS TE M
fP)) (E [~'~~
IPODor
MP3 input © ©
® ®
CDIDVD
A (Left)
A(Ri~ht)
Speaker Spea er
~ ~CJ
© ©
® ®
B (Right) B(Left)
Speaker Speaker
7

__ PT560AU Safety Instructions
SAFETY INSTRUCTIONS
1. Make sure that all connections are properly connected and the main
volume is set to minimum level before turning on the unit.
2.
When more than one pair of speakers are used, (specially the main
speaker output) make sure that the speakers used are of the same
wattage and impedance, otherwise the unit maybe damaged under
high power or long term operation.
3. To avoid humming sounds and unwanted noise, make sure that all the
wires are properly inserted.
4. For speaker cords, strip off the vinyl coating and twist the wire tip.
Push
down the pink jack or loosen the screw terminal, before inserting
the wire tip, then fasten it and tighten the screw. Be careful not to let
the wires stick out of the terminal otherwise this may cause a short
circuit when wires of different terminal contact each other.
5. After the unit is turned on, adjust the main volume to the desired level
same is true with the bass and treble volume, etc.