PZRacing Start Next ST400 User manual

Start Next & Start Basic ST400
User Manual - v1.0 – 20/07/2022
Index
1 – Introduction......................................................................................................................................................................................................................... 1
1.1 – GPS Technology.......................................................................................................................................................................................................... 1
1.2 – Package content.......................................................................................................................................................................................................... 1
1.3 – Technical features...................................................................................................................................................................................................... 2
1.4 – Important information for correct usage................................................................................................................................................................... 2
2 – hronometer components.................................................................................................................................................................................................. 2
2.1 – Touch screen.............................................................................................................................................................................................................. 2
3 – Installation.......................................................................................................................................................................................................................... 3
3.1 – Positioning................................................................................................................................................................................................................. 3
3.2 – Power......................................................................................................................................................................................................................... 3
3.3 – Internal memory....................................................................................................................................................................................................... 4
4 – How to use Start................................................................................................................................................................................................................. 4
4.1 – Switch on/off............................................................................................................................................................................................................. 4
4.2 – Registering sessions.................................................................................................................................................................................................. 4
4.3 – Screens...................................................................................................................................................................................................................... 4
4.4 – Menu and icons......................................................................................................................................................................................................... 5
4.5 – GPS Signal................................................................................................................................................................................................................. 6
5 – onfiguration, SETUP menu............................................................................................................................................................................................... 7
6 – How to use and choose the finish line/circuit.................................................................................................................................................................... 8
6.1 – losed circuit............................................................................................................................................................................................................. 8
6.2 – Point to point............................................................................................................................................................................................................ 8
6.3 – Acceleration............................................................................................................................................................................................................... 8
6.4 – Dyno Bench (solo Start Next).................................................................................................................................................................................... 8
7 – Storage of a new finish line/circuit..................................................................................................................................................................................... 8
8 – Session analysis.................................................................................................................................................................................................................. 9
8.1 – Viewing sessions and lap times................................................................................................................................................................................. 9
8.2 – Deleting a session...................................................................................................................................................................................................... 9
9 – Viewing values in real time................................................................................................................................................................................................. 9
10 – P connection (only Start Next)....................................................................................................................................................................................... 9
10.1 – USB data download.................................................................................................................................................................................................. 9
10.2 – Wi-Fi........................................................................................................................................................................................................................ 9
11 – Gear indication (only Start Next with box expander)...................................................................................................................................................... 10
11.1 - Setting the gear using RPM/SPEED ratio (only Start Next)....................................................................................................................................10
11.2 - Setting the gear using the analogue input (only Start Next)................................................................................................................................... 10
12 – Linear potentiometer calibration (only Start Next)........................................................................................................................................................ 10
13 – Accelerometer (only Start Next)...................................................................................................................................................................................... 10
14 – Self-diagnosis................................................................................................................................................................................................................... 11
15 – Firmware installed and date of first use........................................................................................................................................................................... 11
16 – Replace the startup image................................................................................................................................................................................................ 11
1 – Intr ducti n
Thank you for choosing a PZRacing product. Start is a state-of-the-art GPS chronometer. There are many advantages to this technology: you will no
longer need to place a bulky infra-red transmitter at the side of the track, you can even view split times on the display and thanks to specially designed
software, you can view all the trajectories covered on a given track. Start is the only chronometer in the world to use a 50Hz receiver and a touch screen
pad with "Gloves Sensitive" technology which makes it possible to use the device even when wearing gloves.
Start Next and Start Basic are tw chr n meters f the same pr duct line and they functi n in the same way. H wever, Start Basic
d es n t all w data acquisiti n and b x expansi n c nnecti n.
Please n te: PZRacing pr ducts are water resistant but n t waterpr f; d n t wash the pr duct with pressurised water and keep
the lateral tab cl sed at all times; failure t d s c uld cause permanent damage t the pr duct.
1.1 – GPS Techn l gy
The Global Positioning System (also known as GPS) is a satellite positioning and navigation system which, thanks to a network of artificial satellites in
orbit, sends information about geographic coordinates and the time to a GPS receiver, in any weather conditions and on any place on Earth. Its
functioning principle is based on a spherical positioning method which measures the time taken by a radio signal to cover the distance from a satellite to
a receiver. One of the main features of GPS receivers is the update frequency expressed in Hertz (Hz); this measurement unit indicates how many times
per second the satellite receiver is capable of updating its position. Start has a state-of-the-art GPS receiver with an updating frequency of 50Hz (50
times per second), which translates into higher precision in calculating the time and visualising trajectories.
1.2 – Package c ntent
–Start Next / Start Basic
–USB cable type
–Fixing Velcro strap
–No.4 screws for plastic adaptor
–Plastic adaptor for bolt
–M6x3cm bolt for fixing onto the bracket
–Self-locking M6 nut
–Metal washers
–No.1 anti-vibration PV plane washers
–No.1 anti-vibration PV conical washers
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

1.3 – Technical features
Start Basic - Lap timer without data acquistion Start Next - Lap timer with data acquistion
•Integrated 50Hz GPS receiver
•Touch screen with "Gloves Sensitive" technology
•1/100s precision
•Management of up to 3 split times
•GPS speed visualization
•Ideal time
•2 predicted time visualizations
•Total time session visualization
•Storage of values per lap and absolute best
•"Best Lap & Split Time" /Maximum RPM /Temp warning Led
•2 engine meters
•2 odometers
•Automatic circuit recognition
•Global circuits database
•P set-up of a new circuit
•Integrated lithium battery
•Automatic shut down
•Back light
•Anti-impact container
•Water resistant
•Size: 85,6x70,5x27,6mm
•Integrated 50Hz GPS receiver
•Touch screen with "Gloves Sensitive" technology
•1/100s precision
•Management of up to 3 split times
•GPS speed visualization
•Ideal time
•2 predicted time visualizations
•Total time session visualization
•Internal triaxial accelerometer
•5 visualization screens
•Storage of values per lap and absolute best
•Storage of the trajectories
•"Best Lap & Split Time" /Maximum RPM /Temp warning Led
•2 engine meters
•2 odometers
•Retrieval of up to 9 analogue channels and 3 digital channels
•50Hz sampling of the connected channels
•Inserted gear indicator (optional)
•Data download by USB and Wi-Fi
•Automatic circuit recognition
•Global circuits database
•P set-up of a new circuit
•P software for data analysis
•Integrated lithium battery
•Optional external battery connection
•Automatic shut down
•Back light
•Anti-impact container
•Water resistant
•Size: 85,6x70,5x27,6mm
1.4 – Imp rtant inf rmati n f r c rrect usage
–This device is to be used exclusively in open spaces
–In order to use the device, you must wait for satellite reception to have been completed; the GPS icon in the top left hand corner will appear on
a black background when reception is complete (see chap. 4.5)
–After a long period of inactivity, satellite detection may take up to 4/5 minutes
–In normal conditions when used on the track, satellite retrieval will only take a few seconds.
2 – Chr n meter c mp nents
2.1 – T uch screen
Start has eliminated selection buttons which are difficult to press when wearing gloves; with Start, you select and scroll directly on the display thanks to
a touch screen pad and "Gloves Sensitive technology" which makes it possible to apply the pressure required even when wearing gloves. In addition, the
icons make it even more simple and intuitive to use the device.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

3 – Installati n
3.1 – P siti ning
Start's integrated GPS receiver make installation easy. Place the chronometer in a spot where it has
good visibility of the sky and where the pilot can see it well. The GPS receiver is located in the
superior part of the device, this is why it is advisable t install Start in a 45° blique
p siti n, see lateral picture.
In h riz ntal p siti n the GPS signal suffers str ng degradati ns as the GPS receiver
view nly ne part f the sky and will als receive an am unt f reflected waves fr m
the gr und that disturb the signal quality.
N.B: check that nearby and ver the upper side f the pr duct, where the gps receiver
is l cated, there’s n metal, carb n r electr nic items; ne f these items c uld
cause the degradati n f the satellite signal and the malfuncti n f the lap timer.
N.B: d n’t place an nb ard camera neraby the lap timer because the internal electr nic f the camera cause the degradati n f the
satellite signal and the malfuncti n f the lap timer.
N te f r R1 2015/18: d n’t place the lap timer nearby the riginal dashb ard f the m t rbike because the internal electr nic f the
TFT dash causes the degradati n f the satellite signal and the malfuncti n f the lap timer.
It is possible to fix the device with the plastic Velcro provided or create a bracket following these instructions:
- Prepare a bracket with a 5mm thickness and a 15mm hole (GENERAL
SUPPORT)
- Insert the head of the M6 bolt in the designated space on the back of the
shell of the Start device
- Fix the bolt with the plastic adaptor making the seat match the head of
the bolt.
- Secure the 4 screws to fix the plastic adaptor
- Insert an anti-vibration conical washer in the bolt between the shell and
the bracket
- Insert the bolt into the bracket
- Insert the second anti-vibration plane rubber washer
- Insert the plane metal washer
- Place the nut provided on top of the metal washer and screw to hold in
place
Please n te: absence f anti-vibrati n washers r inc rrect p siti ning f these c uld damage the device due t vibrati ns f the
vehicle. This type f damage is n t c vered by the guarantee as it is n t caused by a pr duct defect but inc rrect installati n.
3.2 – P wer
Start is fitted with a 2000mA lithium battery; you can see the status of the battery on the icon in the top right hand corner of the main screen.
Battery charge L w battery
To charge the battery, attach the USB connector of Start to a power source or USB port on your P using the USB cable provided; the image of a battery
being charged will appear on the display.
Once the battery is fully charged, " harging complete" will appear on your display; you can now disconnect the USB cable.
(only Start Next) You can also charge the product directly on the vehicle by purchasing the optional SS12V100 cable or the SS12 AR cigar lighter cable;
when using these devices, the battery will be charged only when the product is switched on.
Please n te: in rder t use s me f the sens rs t apply t the Expansi n m dules, y u need t use the pti nal SS12V100 cable;
read the technical descripti n f the sens rs y u wish t install carefully.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

3.3 – Internal mem ry
The memory contains sessions and data saved by the device; it also contains system configuration folders and the coordinates of the finish lines of the
tracks. The memory card contains the following folders:
Folder: SYSTEM File: ONFIG. FG (file for all product configurations)
Folder: TRA KS File: *.TRK (file for the finish line and split time coordinates)
Folder: SESSIONS File: *.SES (saved sessions file)
Folder: MANUALS File: *.pdf (instructions manuals in several languages)
Folder: IMAGE File: *.bmp (startup image, monochrome bitmap 128x64px)
Please n te: All the names and c ntents f the f lders and files have been appr priately f rmatted; DO NOT change them
manually; nly use Race Pr s ftware t read/write the file.
4 – H w t use Start
4.1 – Switch n/ ff
To switch on the device, keep the ON/OFF button pressed until the Start logo appears on the display. To switch off, keep the ON/OFF button pressed
until the device switches off.
Start also has an automatic shut down feature which switches the device off after 20 minutes of inactivity.
4.2 – Registering sessi ns
Start will begin to register a new session every time the three following conditions are met:
- the GPS signal has picked up the satellite signal
- the chronometer has been activated (we remind you that the chronometer starts when the internal accelerometer retrieves the departure of the vehicle)
4.3 – Screens
The following information is always displayed on the top line of the main screen: GPS (GPS receiver connected to satellites), RE (recording ongoing);
time, battery level; the bottom line always display the time per lap.
The remaining area of the screen displays the following information: lap time (01'41”58), best lap (01'41”02), speed (265) and the circuit/acceleration
type (MISANO):
SCREEN 1
DURING LAP UNDER FINISH LINE
Cr ssing the finish line, the difference fr m the best lap f the sessi n will be displayed instead f the "Best Lap".
(Only Next versi n)
By inserting at least one Box Expander, you activate new visualisation screens which can be selected by pressing the lateral "switch on" button for one
second; the screens available are the following and it will also be possible to view RPMs ( 15500), temperature (113), analogue 1 (580), inserted gear
(6), best lap (01'41”58) and the circuit/acceleration type (MISANO):
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

On screens 2 and 3, visualization of the gear can be deactivated (image on the left) or activated (image on the right); follow the instructions in hap. 11
for gear settings.
4.4 – Menu and ic ns
To access the menu, touch any part of the display. As previously described, all actions and menu entries are
represented by descriptive icons which can be divided into 3 categories:
MENU ICONS
EXIT LAPS DATA TRA K SETUP GEAR SUSPENSIONS INFO
LAPS: to view the sessions and lap times stored on the memory card
DATA: to view the meters, speedometers and highest values stored
TRA K: circuit and conditions of use settings
SETUP: general device settings
GEAR (only Start Next): gear settings
SUSPENSIONS (only Start Next): setting the minimum suspensions travel (“ZERO setting”)
INFO: general information about the product and system
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

SUBMENU ICONS
VALUE SAT TEST EXIT
VALUE: real time visualisation of values
SAT: visualisation of used and queued satellite signals
TEST: self-diagnosis to verify the features of the product
EXIT: to go back to main menu
EXIT: to go back to the main screen
ICON SELECTION
UP DOWN NEXT SHIFT ERASE NEW YES NO
UP: scrolls upwards
DOWN: scrolls downwards
NEXT: scrolls to next entry
SHIFT: changes the selected entry
ERASE: deletes the selected entry
NEW: button to create a new file with the coordinates of a new finish line
YES: to confirm the selected command
NO: to reject the selected command
4.5 – GPS Signal
GPS signal acquisition can take from a matter of seconds to a couple of minutes. If the device has been switched off for days or the circuit has changed,
the time required for the first satellite retrieval can take 4/5 minutes; when used regularly, detection takes very little time. Acquisition of the GPS signal
is indicated on the display by the GPS icon:
GPS receiver has detected the satellites GPS receiver has n t yet detected the satellites
It is also possible to check the signal received by the satellites by accessing the menu, selecting the INFO icon and subsequently the SAT icon; the ID
numbers of the satellites will appear together with the dB power signal received; if the signal bar is full the satellite is being used, if not, it isn't.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

5 – C nfigurati n, SETUP menu
Below you find all the SETUP menu entries and their descriptions
Language
It is possible to select the language of the device:
- EN: English (default)
- IT: Italiano
- DE: Deutsch
- FR: Francais
Rec rding
Recording mode can be set according to two configurations:
ALWAYS: recording always activated, every time the chronometer starts to count; a new file will be created and a new session will be recorded (default)
MANUAL: recording is manual, every time you go back to the main screen, you will be asked to save the new session
Time f rmat
Time format setting: 12h o 24h.
Data f rmat
Data format setting: day/month/year or month/day/year.
Time z ne
Time zone setting, set the time difference from Greenwich Mean Time (GMT).
Freeze time
Sets the seconds per visualisation of the time per lap upon reaching the finish line 10 – 60 seconds (30 second default)
Cr n m de
Setting of the visualization of the time during lap:
ROLLING: classic visualization with time rolling
PRED. DELTA: predicted delta, predicted difference of the current lap with the best lap
PRED.TOTAL: predicted total, predicted time visualization
Best/T tal
Best lap or total time session visualization:
BEST: display of the best lap during the lap and of the gain/loss time compared to the best lap when passing the finish line/split times
TOTAL: display of the total time of the session (specific function for off-road use)
Speed unit
Set the speed unit: Km/h (metric, default), mph (imperial)
Temperature (s l Start Next)
Set the temperature (this setting is of no use if the device is not attached to a Box Expander): ° (Degrees elsius, default), °F (Fahrenheit)
Pulse RPM (s l Start Next)
Set the RPM reading parameters (this setting is of no use if the device is not attached to a Box Expander):
1 - one pulse per drive shaft rotation (ex. standard 2 stroke engines)
2 - two pulses per drive shaft rotation (ex. 2 stroke engines with waste spark)
4 - four pulses per drive shaft rotation (ex. 2 stroke engines with waste spark)
½ – one pulse per two drive shaft rotations (ex.: standard 4 stroke engines)
Led (s l Start Next)
onfigure the use of the led:
BEST: the led switches on when retrieving the best lap or the best split time of the session (default)
RPM: maximum RPM exceeded, the led flashes when an RPM threshold is exceeded
TEMP: temperature alarm function, the led flashes when a set temperature threshold is exceeded.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

6 – H w t use and ch se the finish line/circuit
Before using the device, you need to choose the way in which you want to use the Start device:
LOSED IR UIT: circuits where the start and finish line coincide (ex. racetracks, kartdromes, etc.)
POINT TO POINT: circuits where the start and finish line do not coincide (ex. rallies, up-hill races, etc.)
A ELERATION: for acceleration races where the finish line corresponds to reaching a certain distance or speed (ex. 0-100 km/h, ¼ mile, etc.)
DYNO BEN H: to use the lap timer even without GPS signal, ideal for dyno bench use
You select the finish line and circuit from the TRA K menu; access the Menu and click on the TRA K icon.
6.1 – Cl sed circuit
The standard mode of a track chronometer, in which a session is made of multiple times per lap; each time the finish line is crossed, the chronometer
records the time taken to perform the lap and sets the chronometer back to zero to start a new lap.
On the first line where "Select" appears, click on RA E (you can amend your choice by pressing SHIFT); press NEXT to confirm.
6.2 – P int t p int
Standing start mode; thanks to the internal accelerometer, Start will retrieve the starting point; the finish line will be
retrieved using the GPS coordinates stored on the device, like with a normal circuit, in the TRA KS folder of the
memory card.
For a standing start, you need to set on MANUAL the start mode of the recording (see chap. 5); this way you can first
position the vehicle up to the starting point, then press YES to request the beginning of the storage when the vehicle
is standing and ready to start the lap.
In the TRA K menu, press "Select" and choose RA E (you can change your choice by clicking on SHIFT), press
NEXT to confirm your choice.
6.3 – Accelerati n
Standing start mode; thanks to the internal accelerometer, Start will retrieve the starting point; the finish line will be retrieved using one of the options
suggested depending on the type of race you are doing. Using this mode, each session has a single lap.
Press "Select" and choose A ELERATION (you can change your choice by clicking on SHIFT), press NEXT to
confirm your choice.
You will then be asked the finish line "Mode"; you can choose from the following entries: 100mt, 150mt, 400mt,
800mt, 1000mt, 0-100Km/h, 0-160Km/h, 0-60mph, 0-120mph, 1/2mile, 1/4mile, 1/8mile.
By choosing A ELERATION, the storage function of a new session is automatically set to MANUAL so you can
position the vehicle on the starting line and then press YES when the vehicle is standing and ready to start.
6.4 – Dyn Bench (s l Start Next)
Dyno Bench mode is the ideal to record data from your bike without GPS signal, so you can use it even on a building
to record performance of your motorbike over a dyno bench.
Select DYNO BEN H and then press NEXT
7 – St rage f a new finish line/circuit
You can download a list of the most famous world circuits directly from our website; if your racetrack is not available, you can create a new circuit using
the RacePro software (see the software manual for details) or directly on the track by doing as follows:
Access the TRA K menu and select the NEW icon in the bottom left hand corner. The following screen will appear:
GPS: it informs us whether the GPS receiver is connected
to the satellites.
I1: saves the coordinates of split time 1.
FINISH: saves the coordinates of the finish line
EXIT: exits the procedure without saving
Wait for the GPS to retrieve the satellites (the letters GPS on a black background like in the photo); place yourself in the spot where you wish to store the
coordinates, press the "I1" button if you wish to save split time 1 , press "Finish" if you want to save the finish line. When you press the button you have
chosen, the icon you selected will turn into a confirmation icon , if you press "Finish", the procedure will be complete and the track will be saved in
the TRA KS folder of the memory card under TRA Kxxx.TRK (xxx are a sequence of numbers); if you press "I1", the following screen will appear where
you can set the second split time or simply the finish line, and so on up to three split times.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

8 – Sessi n analysis
8.1 – Viewing sessi ns and lap times
Access the device menu and select the LAPS icon; if there are no sessions registered, the device will return to the
main menu; otherwise, the following screen will show the information relating to the first session.
To scroll through the sessions, click on the arrows UP and DOWN; press the centre of the display to access and
see the session times.
Press the UP and DOWN arrows to scroll the bar up and down; once you have chosen a time per lap you can
press NEXT and view the details of a single lap.
Press one of the arrows (UP or DOWN) to view details of the previous or following lap, or press at the centre of
the display to go back to the previous screen.
8.2 – Deleting a sessi n
Access the device menu, click on the LAPS icon, view the session you wish to delete, press ERASE then confirm deletion by pressing the YES icon.
9 – Viewing values in real time
The real time values screen allows you to see all the measurements retrieved by the GPS, all the analogue and digital measurements retrieved by the Box
Expander; from this screen it is possible to calibrate the sensors connected (the so-called "zero" of the sensors).
To access these screens, access the menu, select the INFO icon and then select VALUE; a series of screens will appear and you can scroll these by clicking
on the UP and DOWN arrows:
With regard to the analogues and SPEED 1 and SPEED 2, these will appear with their default name if they have not been changed; if they have been
changed, the name associated to the analogue access will appear.
To change the name, you need to open the configuration file ONFIG. FG in the RacePro software and refer to the software manual.
10 – PC c nnecti n ( nly Start Next)
10.1 – USB data d wnl ad
The files contained in the memory are managed like any files in a digital archive memory (USB stick, memory card, etc,); this is why there is no
download time, you simply need to connect the Start device to the P and copy the files contained in the SESSION folder.
The *.SES file is formatted as follows:
NAME DATE TIME IR UIT BEST-LAP IDEAL-TIME.SES
Do not rename the session files under any circumstances; Start will no longer be able to open the files.
To eliminate the content of the memory, eliminate all the files inside the SESSION folder.
10.2 – Wi-Fi
The new Start Next ST400-N is equipped with an integrated Wi-Fi module that will be
used for data download and settings related to storage. Wi-Fi turns on when the product
is turned on and turns off when the motorcycle exceeds 30Km/h, to reactivate the Wi-Fi
it will be necessary to turn off and on the GPS receiver.
N.B: the Wi-Fi m dule is active nly n the main screen and when the
pr duct is charging, it is deactivated when y u br wse the menu.
After connection between RacePro and Start Next, all the sessions stored in memory will
be displayed, select a session and click the “Download Session” button to start the data
download or the “Delete Session” button to delete the session.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

The default data for the Wi-Fi network are the following:
Network name: PZRacing ST400N-USER 1
Password: 12345678
From the software, in the Network tab, it is possible, and rec mmended, to change the last part of the network name (USER 1) and the password.
Once modified it will be necessary to close the RacePro program, turn off and on the GPS receiver.
11 – Gear indicati n ( nly Start Next with b x expander)
Start can view and save the gear inserted in two different ways:
- calculating the RPM/speed ratio (for vehicles which don't have a potentiometer on the gear)
- retrieving the analogue exit of the gear potentiometer
By accessing the "GEAR" menu, the screen you see here to the side will appear.
11.1 - Setting the gear using RPM/SPEED rati ( nly Start Next)
The first entry you have to set up is visualization of the gear inserted on the display; if you select "NO”, the gear will only be saved; if you select "YES",
the gear will also be viewed on S REEN 2 and S REEN 3.
After "Input", select "RPM/SPEED1" if you wish to use the speed of the Box Expander 2, select "RPM/SPEED2" if you wish to use the speed registered by
the Box Expander 3.
Then press the " ALIB." button to perform calibration of the inserted gear; the screen that appears will be a confirmation screen with the options "YES"
and "NO". Before clicking "YES", we advise you to switch on the vehicle and put into first gear with the clutch pulled.
Perform calibration as follows:
- lick on the "Yes" button.
- Number "1" will appear; put into first gear, release the clutch and continue at constant engine speed (approx. 5000
RPMs).
- After about five seconds, number "2" will appear; put into second gear and continue at constant engine speed
(approx. 5000 RPMs).
- Do this with all the gears of your vehicle.
- When the number that comes after the number of gears appears on the display (ex. if your bike has 6 gears, wait for
number 7), press STOP to terminate calibration.
11.2 - Setting the gear using the anal gue input ( nly Start Next)
The first entry you have to set up is visualization of the gear inserted on the display; if you select "NO”, the gear will
only be saved; if you select "YES", the gear will also be viewed on S REEN 2 and S REEN 3.
Under "Input", select analogue input to which the gear potentiometer output is connected.
Then press " alibration" to calibrate the gear; the screen which will appear will be a confirmation screen with the
options YES and NO.
You do not need to start the vehicle to perform the calibration, but you need to access the instruments panel.
- Press "Yes".
- Number "1" will appear, put into first gear.
- After about five seconds, number "2" will appear; put into second gear.
- Do this with all the gears of your vehicle.
- When the number that comes after the number of gears appears on the display (ex. if your bike has 6 gears, wait for
number 7), press STOP to terminate calibration.
12 – Linear p tenti meter calibrati n ( nly Start Next)
It is possible to calibrate the linear potentiometers directly from the instrument.
N.B: it is necessary t have c nfigured the anal gue channels fr m the RacePr s ftware using the
presettings f r the linear p tenti meters (POTENTIOMETER 150mm and POTENTIOMETER 75mm),
it is p ssible t calibrate nly the anal gue inputs set with ne f these tw v ices.
Enter the menu and click on the SUSP icon, the analog inputs set as linear potentiometers will be displayed, select the potentiometer you want to
calibrate, bring the potentiometer to its maximum extension and press ALIB icon.
13 – Acceler meter ( nly Start Next)
Start is equipped with an internal accelerometer that is used for detecting the start and to store the values on the
recorded file.
We remind you that in order to have a correct reading of the values of the internal accelerometer it is necessary to
install the Start integral with the vehicle frame, therefore the data stored by installing the lap timer on the steering
wheel or on the fork plate will not be truthful.
On the side the orientation of the accelerometer axes.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]