Quam SYSTEM 17 Series User manual

GENERAL DESCRIPTION
The SYSTEM17 Series consists of versions of a complete
loudspeaker with a 8” O.D. wide frequency response speaker,
multiple transformer options, perforated steel baffle, and
integral molded fiber enclosure.
Finish: Baked epoxy hybrid.
MODELS
SYSTEM17 10W*, 70.7V, pigtail select
SYSTEM17/25RS 4W**, 25V rotary select
SYSTEM17/70RS 4W**, 70.7V rotary select
SYSTEM17/8 20W, 8-Ohm

*10W,5W,2.5W,1.25W,0.63W
  **4W,2W,1W,0.5W,0.25W
INTENDED USE
All versions: Indoor environment, mounted parallel to floor plane in
a 24” wide suspended ceiling tile grid.
Program Material: Signal tones, voice and music.
SYSTEM COMPONENTS
Loudspeaker 8C10FEPAX
FINISH OPTIONS
White Order as SYSTEM17, SYSTEM17/25RS,
SYSTEM17/70RS, SYSTEM17/8
Black Order as SYSTEM17/B, SYSTEM17/25RS/B,
SYSTEM17/70RS/B, SYSTEM17/8/B
Quam-Nichols Company
234 East Marquette Road, Chicago, IL 60637
Phone: (800) NEED NOW Fax: (888) NEED NOW
(800) 633 - 3669 (888) 633 - 3669
E-Mail: [email protected] www.quamspeakers.com
© 2012 Quam-Nichols Company Quam-Nichols reserves the right to make changes and/or improvements to its products at any time and without notice. TSYSTEM17_12JN19
AUDIO SPECIFICATIONS:
Average Sensitivity 95 dB-SPL, 1W/1M
Loudspeaker Power 20W RMS, EIA 426A Standard
Rating
Calculated Maximum 105 dB-SPL, 10W/1M
System Output
Magnet Type, Weight BeFe Ceramic, 10oz. Nominal
Frequency Response 50Hz - 18 kHz (SYSTEM17, SYSTEM17/8)
65Hz - 18 kHz (SYSTEM17/- RS versions
EIA 426A Standard
Nominal 100°Included angle, -6dB
Coverage Angle 2 kHz, half space
Audio Connection 7” long, labeled tinned wires,
pre-cut
LOUDSPEAKER ASSEMBLIES 01
0104.5 - TILE REPLACEMENT LOUDSPEAKER
SYSTEM17
Extended Frequency Response, 70.7V Pig-Tail Lead
SYSTEM17/8
Extended Frequency Response, 8-Ohm Pig-Tail Lead
SYSTEM17/25RS
Extended Frequency Response, 25V Rotary Select
SYSTEM17/70RS
Extended Frequency Response, 70.7V Rotary Select
Since 1930
IBEW
1031
LU
SYSTEM17 Shown
23-13/16
23-13/16
3-7/16
Recommended construction sequences, installation instructions,
and A&E Guide Specifications are available on the web at:
www.QuamSpeakers.com/ Resources /A&E Resources

234 East Marquette Road, Chicago, IL 60637
Phone: (800) NEED NOW Fax: (888) NEED NOW
(800) 633 - 3669 (888) 633 - 3669
E-Mail: [email protected] www.quamspeakers.com
(1’ x 2’) SYSTEM 5/VC, SYSTEM 14, SYSTEM 16 – includes 8-Ohm, /25RS and /70RS versions
(2’ x 2’) SYSTEM 12/VC, SYSTEM 15, SYSTEM 17 – includes 8-Ohm, /25RS and /70RS versions
INSTALLATION INSTRUCTIONS
© 2012 Quam-Nichols Company Quam-Nichols reserves the right to make changes and/or improvements to its products at any time and without notice.
12– 2.20 8088
4. Feed supply cable through whip to connector.
Make connections per wiring diagrams below;
Insulate all unused taps from each other, the enclosure
and electrical ground.
When cover plate is secured, all connections / splices and
unused leads must be inside of the enclosure.
5. Place assembly onto ceiling grid, install 24” T-bar
trim piece where required (furnished only with specific
1’x2’ formats).
NOTE! AHJ/ local codes may require tie-off to structure.
Bend up tie-off tabs as shown in illustration and install as
directed.
NOTE! AHJ/ local codes may require tie-down to grid.
Recommended fasteners; not supplied : Erico/Caddy part
ATA4i and 1/4”-20 x 2” bolt, or equivalent. Install as
directed.
6. Place remaining ceiling tile into opening as required.
BLACK ( Common )
BLACK ( Common )
8Ω
8Ω
QUAM /25RS and /70RS Rotary Select
QUAM /25RS and /70RS Rotary Select
4W
4W
0.25W
0.25W
0.5W
0.5W
1W
1W
2W
2W
OFF
OFF
RED
RED
INTENDED USE:
All versions: Indoor environment, mounted parallel to floor
plane in a 24” wide, suspended ceiling tile grid; mount height
18’ or less above floor plane.
Program material: Signal tones, voice and music.
1. Cut ceiling tile as required:
1’ x 2’ FORMAT LOUDSPEAKER
2’ x 2’ tile – Cut tile in half along one axis.
2’ x 4’ tile – Cut 12” from edge along 2’ axis and
discardsmallerpiece.
2’ x 2’ FORMAT LOUDSPEAKER
2’ x 2’ tile – No cutting required.
2’ x 4’ tile – Cut tile in half along 2’ axis.
!Steps 2-3 – Required only if using conduit clamp
fitting
other than what is provided with product.
2. Loosen, but do not remove screws on cover plate;
push up and remove plate from assembly.
3. Remove cable /conduit clamp fitting from plate;
Install UL Listed metallic enclosure entry fitting for
plenum cable or flex whip.
Tie-off
tab 2x
Tie-off
tab 4x
Brown 5W @ 25V only
Red 2.5W @ 25V only
Violet only 0.32W @ 70.7V
Gray only 0.63W @ 70.7V
Blue only 1.25W @ 70.7V
White 0.32W @ 25V or 2.5W @ 70.7V
Green 0.63W @ 25V or 5W @ 70.7V
Orange 1.25W @ 25V only
BLACK ( Common )
8Ω
8Ω
QUAM Model TBLU
BLACK ( Common )
BLACK ( Common )
8Ω
8Ω
QUAM 8-Ohm Operation
QUAM 8-Ohm Operation
RED
RED
Blue 10W
White 5W
Yellow 0.63W
Red 1.25W
Green 2.5W
BLACK ( Common )
8Ω
8Ω
QUAM Model TCH70