Queensland security OSD High Speed Dome Camera User manual

113 Brisbane Rd Mooloolaba QLD 4557
Phone: [phone]
Fax: [phone]
Website: www.queenslandsecurity.net.au
Email:[email protected].au
ACN: 136 757 876
ABN: 26 480 252 132
OSD High Speed Dome Camera
User’s Manual
● Please read the manual carefully before installing and using the unit. ●
We greatly appreciate your choosing our product!

Important Safeguards
1. During the course of transportation and storage, the product should be avoided from incorrect
operations such as heavy pressing, strong vibration, soaking etc, which can cause damage of
product.
2. The product is designed for ceiling or wall installation, so it can not be installed up-side-
down, and it should be handled properly so as not to bring about mechanical problems
affecting the integrative functions of it. The vitreous cover of the dome is complicated optical
component, so do not touch it with bare hand(s). Otherwise, the cover might be scraped, and
image quality affected.
3. Do not put any foreign objects or spill liquids into the unit.
4. Please follow all electrical standards for safety when it is being connected and adopt the
particular power supply which is provided with the unit. The product‟s RS-485 and video
signal adopt TVS-class lightning damage preventing technology, which can effectively
prevent such pulse signal damage caused by lightning under 500W or electric surge. RS-
485 and video signal should keep enough distance with high voltage equipments and
cables when they are in transmission, and necessary steps should be taken to prevent
lightning damage or power surge.
6. Do not let the camera aim at the sun or object with extreme light when it is switched on or off.
Otherwise, the camera‟s CCD might be permanently damaged.
7. There are no user-serviceable parts inside. When mechanical problems arise, do not be in a
haste to do any repairing, please refers to the User‟s Manual. If causes can not be located, please
refer servicing to qualified professionals. All servicing must be done by authorized personnel.
Table of Contents
1. Introduction ------------------------------------------------------------------------------------ 3
2. Technical Data -------------------------------------------------------------------------------- 3
3. Characteristics --------------------------------------------------------------------------------- 4
4. Function ---------------------------------------------------------------------------------------- 4
5. Setup Installation and Connection of the System ----------------------------------------- 6
5.1 Setup of Communication Protocol, Baud Rate and Address of High Speed Dome Camera-----
----------------------------------------------------------------------------------------------- 6

5.1.1 Setup of the Address of Dome Camera-------------------------------------------------- 7
5.1.2 Setup of the Communication Protocol--------------------------------------------------- 7
5.1.3 Setup of the Baud Rate of Communication---------------------------------------------- 7
5.1.4 RS-485 Bus Matching Resistor ----------------------------------------------------------- 8
5.2 Installation and Connection --------------------------------------------------------------- 8
5.2.1Installation Procedures----------------------------------------------------------------------- 9
5.2.2 Ceiling Installation of the Dome Camera ---------------------------------------------- 9
5.2.3 Wall Installation of the Dome Camera -------------------------------------------------- 11
5.2.4 Alarm Connection and installation--------------------------------------------------------11
6. High Speed Dome Camera Controlled by Keyboard-------------------------------------- 13
6.1 Setup and Preview the Preset Positions --------------------------------------------------- 13
6.1.1 Setup the Preset Positions ------------------------------------------------------------- 13
6.1.2 Preview the Preset Positions ------------------------------------------------------------- 14
6.2 Touring Function ----------------------------------------------------------------------------- 14
6.3 Touring Function(special keyboard) ----------------------------------------------------- 15
6.3.1 Setup Tours Data---------------------------------------------------------------------------- 15
6.3.2 Setup Tour------------------------------------------------------------------------------------ 16
6.4 Auto Scan ------------------------------------------------------------------------------------ 16
6.4.1 Scan Between Two Points ----------------------------------------------------------------- 16
7. The Setup, Entering and Exit of Default Position------------------------------------------ 17
8. Troubles Shooting ------------------------------------------------------------------------- 17
9. Address Coding Corresponding Table ----------------------------------------------------------------
18
★The Company reserves the right to interpret changes of product design or specifications.
Please refer to the Company‟s website for related information.
1. Introduction
The smart speed dome camera is a hi-tech product of most advanced manufacturing
techniques and many years‟ of accumulated experience, which represents the future trend of hi-
tech monitoring products. It is configured with a high-performance DSP camera with zooming
lens. The unit is capable of rapid positioning, consecutive tracing and scanning and real
panoramic monitoring. The unit can automatically make adjustment to ambient brightness and
object distance. Its digital control and elegantly simple design maximally reduce connection and
installation processes of components in the system, improving reliability of the system and
facilitate installation and maintenance. Driven by a stepper electric motor, the unit runs
smoothly, reacts quickly and locates positions accurately.

The high speed dome camera with various performances can be applied in every walk of
life to monitor moving objects in large areas, such as monitoring smart building, bank security,
city streets, power departments, airports, bus/railway stations, etc.
2. Technical Data
2.1 Technical Data of High Speed Dome Camera
Power supply
DC14V(2A) or AC24V(2A)
Ambient temperature
indoor：（0ºC～40ºC）outdoor：（-40℃～60℃）
relative humidity
≤95% non-condensing
Power consumption
20W
Communication system
RS485 bus
Baud rate of communication
1200／2400／4800/ 9600bps
Pan speed
0.5º-350º/s（64 ranges）
Max speed
350°/s
Pan movement
360ºendless
Tilt movement
90º
Automatic flip
Automatic 180º flip when vertical 90º
Speed limitation by long focus
The dome can automatically adjust the manually
control speed based on the current focal length.
Scan between 2 points
yes
Scan speed
128 ranges
Preset position number
128
Motor speed to preset position
8 ranges
Dwell time
1~255s
Tour number
4
Preset position number of each
tour
16 preset positions
Pattern Scan number
4
Fan and heater
Fan and heater automatically start（dome camera
with temperature controlling devices）12V DC
or 24VAC
2.2 Camera Lens Data (Built-in HITACHI Integrative Camera)
Model
HITACHI23color /HITACHI23 color (day and night)
Synchronization
Internal sync/external sync
scan
2：1interlace
resolution
> 480 lines
brightness
0.2Lux/0.002Lux
iris
auto/manual
focus
auto/manual
Lens zoom ratio
23×optical zoom
Focal length
3.6/82.8mm
Effective angle
Wide:47º/tele:2.5º
Backlight
auto
White balance
auto
AGC
auto
System of signal
NTSC/PAL

S/N
＞50dB
Signal output
1.0±0.2Vpp
Camera Lens Data (Built-in SONY Integrative Camera)
Model
SONY18 color / SONY18 color (day and night)
Synchronization
Internal sync/external sync
scan
2：1interlace
resolution
> 480 lines
brightness
0.7Lux/0.001Lux
iris
auto/manual
focus
auto/manual
Lens zoom ratio
18×optical zoom
Focal length
4.1/73.8mm
Effective angle
Wide:47º/tele:2.7º
Backlight
auto
White balance
auto
AGC
auto
System of signal
NTSC/PAL
S/N
＞50dB
Signal output
1.0±0.2Vpp
3. Characteristics
Adopting multi-functional high-performance DSP design with stable performance
Powerful OSD menu which is direct, convenient and easy to operate.(English and Chinese
interface alternative)
Internally-saved data will not lose within one year after power off
Integrative design with compact structure and high reliability
The unit is equipped with a camera system which can automatically identify some brands of
cameras. The cameras belong to the 2 famous brands—SONY and HITACHI.
128 preset positions for random storage and accurate locating
Precise electric motor drive ensuring smooth running and agile reaction
Pan 360°consecutive movement, panoramic monitoring
Tilt 180°automatic movement, consecutive monitoring
Automatically adjusting movement speed according to lens zoom ratio
Automatic aperture, focus and white balance
The unit has a default position. The user can setup default position for a key monitoring area
according to actual conditions. If not operated after 10 minutes, the dome camera will
automatically monitor the preset position.

4. Description of Functions
1. Trace the Target
Users can control pan/tilt to trace the target or change visual angle by keyboard or matrix, and
target size on the screen can change by control zoom. With the movement of the camera, the
speed dome camera can automatically adjust lens to get clarity picture on the screen when zoom
focus and aperture is set to auto mode (default).
2．Automatic Adjustment of Focal Length/Movement Speed
When the focus is long and in the mode of manual adjustment, even the slightest movement
of the joystick would make the highly-sensitive dome camera to move quickly, causing pictures
losses. Based on human design, the dome can automatically adjust the manually controlled dome
pan/tilt speed according to the current focal length, making the manual target tracing an easy
operation.
3．Automatic Flip
Keep the tilt travel down to bottom, and the dome can automatically give a pan 180° flip,
then a tilt 90° flip, which enables the user to observe rear objects, and ensures tilt 180°
consecutive panoramic monitoring.
4. Setup and Preview Preset Positions
The preset function works in this way: the dome camera stores data of the current dome
pan/tilt angles and lens focal length; when needed, preview these data, then move the dome and
camera to the assigned position. The user can quickly and conveniently preview the preset
position with the controlling keyboard. The dome camera support 128 preset positions.
5. Automatic Tours
The automatic tour function is a built-in function of the camera, which is realized by
beforehand programming, that is, arranging preset positions into the automatic tour in the desired
order, then, the user can use such equipment as controlling keyboard to make the dome camera
automatically move to and fro along the preset positions for preset time.
● Automatic tour among preset positions can be realized through inserting preset
positions into the tour.
● The tour order is programmable. When running a tour, and the dwell time at the
preset positions is adjustable.
● Sixteen preset positions can be stored in the tour.
6. Automatic Scanning

Left/right positions can be setup through controlling keyboard, and the camera can auto-scan
horizontally between the left position and right position, at the preset speed.
7. Camera Lens Control
To get desired panoramic view or close shot, the focal length can be adjusted through the
controlling keyboard.
Focal Length Control
To get desired panoramic view or close shot, the focal length can be adjusted through
the controlling keyboard.
Focus Control
The system has automatic focus function (default). With its movement, the camera can
automatically adjust focus to the center of the object view to get clear picture. Under special
circumstances, the user can manually adjust the focus to achieve desired image effect.
● Manual focus is okay through the controlling keyboard or matrix. For details, please
refer to the operation manual of the controlling keyboard or matrix.
● In the state of manual focus, operating focal length control will automatically focus
on objects. If the dome camera is setup to resume auto-focus by joystick operation,
when operating the joystick, the dome camera will automatically focus. If an auto-
focus resumption time is setup, the dome camera will resume auto-focus after the
setup resumption time period without receiving controlling orders.
Under the following circumstances, the camera can not carry out auto-focus:
● When the object is not the center of the view
● When simultaneously observe a far object and a near one, clarity of both can not be
guaranteed.
● When observing objects of extreme brightness, such as neon lights, spotlight, etc
● When the object is behind glass with water drops or dust
● When the object moves very fast
● When the object is large-size and drab, such as wall
● When the object is too dark or fuzzy

Aperture Control
● The system has automatic aperture function (default). The aperture can auto-sense the
surrounding brightness and make quick adjustment, which stabilizes image brightness.
● To obtain desired image brightness, the aperture can be adjusted manually through the
controlling keyboard.
Automatic Backlight
The camera can automatically backlight on a discretionary basis. In extremely
bright background, the camera can backlight those relatively dark objects, while adjust
the lighting of the bright background, which ensures the clarity of images, and prevents
the image from becoming flashing whiteness due to the extremely bright background
and also avoids indiscernible dark objects
Automatic White Balance
Based on ambient brightness, the camera can automatically adjust itself to represent
real colors.
5. Setup, Installation and Connection
5.1 High Speed Dome Camera Address, Baud Rate and Protocol Setup
Before installation of the dome camera, you must confirm the protocol and Baud rate,
and address code of the controlling system, then, setup the switches to conform to the
controlling system. Please note that Binary System is adopted for all the switches code. The
corresponding switch setup is shown in the following figure:
5.1.1 Setup Communication Protocol and Baudrate of the High Speed Dome
Camera:

DIP-1 to DIP-2 of SW2 on the PCB panel is for communication protocol setup. Please
refer to the following table:
Code
2 1
Protocol
1
0 0
PELCO_D
2
0 1
PELCO_P
5.1.2 Setup Baud Rate of Communication
DIP-3 to DIP-4 of SW2 on the PCB panel is for Baudrate setup. The default setup is 4800bps.
Please refer to the following table:
Code
4 3
Baudrate
1
0 0
1200BPS
2
0 1
2400BPS
3
1 0
4800BPS
4
1 1
9600BPS
5.1.3 Setup the Address of the Dome Camera
Before formal operation, the address of the dome camera should be setup. SW1 on the
PCB panel is used to set address of the dome camera from 1 to 255. The coding switches from
DIP-1 to DIP-8 are equivalent to a 8-bit binary figure. The state “ON” of each bit means “1”
while”OFF”means”0”. Corresponding state of coding switches and address is shown in the
appendix table.
◆If protocol, address and Baud rate are setup when power is on, then the high speed dome
camera must be switched off and restarted to make the setup valid.
5.1.4 RS-485 Bus Matching Resistor
If the dome camera is used at the farthest terminal, there should be a parallel connection of a
120Ω terminal matching resistor between A, B lines of RS485.
5.2 Installation and Connection
There are three types of the installation of high speed dome camera, whose dimensions are
shown below:

· Wall installation
Ceiling installation
· In-ceiling installation (the camera‟s dimensions are different from the former two)
Products
The style of
installation
bracket
cable（with
connector）
High
Speed
Dome
Camera
wall installation
Wall bracket
Power supply
cable
video cable
485 cable
1 5-core cable
(alarm input)
1 2-core cable
(alarm output)
ceiling installation
Bracket with the
length of 20 to 40 cm
In-ceiling installation
No bracket
Remarks:
1. The connection must be carried out by qualified personnel conforming to local regulations.
2. For connection details, please refer to the silk-screen printing indications and installation
instructions on the PCB panel.
3. The vitreous cover of the dome camera is complicated optical component, so do not touch it
with bare hand(s). Otherwise, the cover might be scraped, and image quality affected.
4. To ensure the clarity of images, please clean the vitreous cover regularly. Take care when
cleaning it. You can only hold the outer ring of the vitreous cover. Do not touch it with bare
hand(s), for acid sweat left may erode the surface plating of the vitreous cover, or hard things
may scrape the vitreous cover leading to fuzzy image and, hence, affecting image quality.
Please use adequately soft dry cloth or other substitutes to clean the inner and outer surfaces.
If the vitreous cover is extremely dirty, it may be cleaned with mild detergent.

Preparation of the Installation
5.2.1 Requirement for the Installation
· To avoid mistakes, installation must be done by qualified personnel conforming to related
regulations.
· Please check whether the attachments are all ready, and whether the installing location and
type of installation are compatible.
The components of the high speed dome camera include bracket, housings, power supply,
decoding panel, dome, temperature controlling devices, etc.
When the dome camera leaves factory, it has undergone installation testing, so the user
only needs to install the bracket, and fix the dome camera on the bracket.
However, before installation, the user should open the vitreous cover and make sure the
screws are tight and cable connectors not loose.
5.2.2 Wall Installation of Dome Camera
Installation of Wall Bracket
Remarks: The wall of the selected installation location must be firm without peeling. To
avoid quivering images resulting from unstable installation, make sure the place for
installation can sustain five times the total weight of the dome camera, the bracket and
the base.
A Use the bracket as template and draw the positions of the installing holes on the desired
wall locus;
B Use an electric drill to make four holes for M6 screws on the above-drawn positions, and
drive in the special M6 screws;
C Push the power cable, communication cable and video cable through the bracket tube,
leaving long enough cables for connection;
D Fix the bracket firmly on the wall with four M6 screw nuts and washers.
辅助挂钩
Wall Bracket Installation Dimensions
Ancillary pegs

Installation of high Speed Dome Camera
a. Unpacking the carton and carefully take out the dome camera and its attachments, open
the vitreous cover and take out the fillings.
b. Loosen the M3 screws connecting the camera and the outer housing, and swivel the
camera left for 15 degrees and remove it, then check cable connectors and see if any of them
loose and setup the coding switch.
c Restore the plastic washer to the camera, then tighten the installation of camera and outer
housing according to the installation instructions indicated below:
Installation of the Camera:
三处安装扣
机芯锁紧螺柱
三处安装槽
机芯锁紧
螺钉过孔
扣板
机芯
Locate the three installing slots at the bottom of the camera into the three pegs on the housing
peg-board (be sure in right direction), and lock them in place then swivel the camera right for 15
degrees, to the point where the fixing screw holes in the camera meet the corresponding screws.
Finally, fix the camera with the outer housing with M3x6 screws.
Insert the cables into the bracket tube and pull them through, then push the tube screw on the top of the
outer housing into the screw hole of the wall bracket, then fix it on the bracket with 3 M6 screws.
Fixing the Wall Bracket and High Speed Dome Camera
3 installing
pegs
Camera tightening
screw
Peg-board
Camera
tightening screw
hole
Camera
3 installing
slots

电源压板
Step 1 Put the power device into the connected wall bracket and pin the power device with the
power pinning board, then, tighten the screw lest the power device slides out. (See the above
figure)
Remarks: Please mount the housing-installed wall bracket on the ancillary peg as shown in the
figure below, which can save you troubles.
锁紧螺钉
Step 2
Pull the power cable, video cable and controlling cable out of the bracket tube, and direct the
dotted-line part shown in the figure to the corresponding pegs on the installed peg-board, then
push the bracket downward until it locks in place. After this, direct the screw on the bracket to
one corresponding hole on the lower part of the peg-board and tighten the screw. (See the above
figure)
Connection of Exterior Cables
Connect BNC video outlet of the dome camera with the already disposed video cable, the
power cable with the already disposed power cable (DC14V or AC24V) and RS485 controlling
cable with already disposed RS485 controlling cable. The signal cable of high speed dome
camera is shown below:
Cable
Application
Connecting
Objects
Remarks
Power pinning board
Tightening
screw

Power
cable
DC14V or
AC24V
power
supply
high speed
dome-power
supply adapter
Black
485
cable
485
controlling
signal
high speed dome
-controlling
device
Green（RS485+）、White（RS485-
）
Video
Cable
Camera
signal
Camera-
monitoring
device
BNC connector
5-core
cable
Alarm input
Detector ----
high speed dome
Black(alarm input public port)
Yellow(channel 1 alarm input)
Green(channel 2 alarm input)
Blue(channel 3 alarm input)
White(channel 4 alarm input)
2-core
cable
Alarm
output
High speed
dome ---- alarm
horn
Brown(alarm output pulic port)
Grey(alarm output usually open
output port)
◆Make sure the polarity of RS485 controlling cable connection is correct, A: RS485
positive, B: RS485 negative.
◆If wrongly connected, the dome camera will be out of control.
Alarm connection and installation
Connect the alarm cables according to the sketch below. Once distinguishing the alarm signal,
the speed dome will immediately act as per the process set before, it will start the camera,
display the image of the alarm zone on the monitor, adjust the speed dome at the alarm
point, and monitor the preset position, record what happens at the alarm zone as soon as
possible. Connection of the alarm cables as the sketch below:
Attention:
a. Alarm input must be ON/OFF input signal, any other types of input signal(such as
power voltage etc) is possible to damage the unit. When there is alarm signal from multi
channels, the unit will response to them one by one, the interval is 2 seconds.
b. Once there is alarm signal coming in, the unit will not response to “Scan” , “Cruising”
etc functions. Manual operation is needed to restore “Scan” , “Cruising” etc functions.
c. No matter the alarm function is opened or closed, alarm output always responds. For
example, if the alarm function of the unit is not open, when the unit distinguish alarm
signal, the unit will not be adjusted to corresponding preset position, but the alarm output
still responds.
d. The operation method for alarm function is: through previewing the No. 147 preset
position to open alarm function, through previewing No. 148 preset position to close
alarm function.
Alarm output connection sketch

Connection sketch forAlarm input with Usual-closed detector
Connection sketch forAlarm input with Usual-open detector

Switching on Power
a Make sure the polarity of plugs, sockets and cables connection is correct, then switch on
power
b The dome camera begins to do the self-check by moving pan 360°, tilt 90° to check the
camera lens, the electrical and mechanical structures in pan/tilt state, then executing the
restoration program and resuming its original position. After the dome camera stops moving, it
finishes self-check and is ready to receive controlling instructions
c Use controlling device to control the dome camera, checking whether it can perform dome
and camera lens functions. If not, please check setups of communication protocol, Baud rate and
address, and connection of 485 controlling cable.
Vitreous Cover Installation
a To avoid scraping the vitreous cover, please clean the dust and stain on it with soft cloth;
b Aim the four special screw holes in the vitreous cover at those in the outer housing, and fix it
with four special screws.
5.2.3 Ceiling Style Installation
Remarks: The wall of the selected installation location must be firm without peeling. To
avoid quivering images resulting from unstable installation, make sure the place for installation
can sustain five times the total weight of the dome camera, the bracket and the base.
A Use the bracket as template and draw the positions of the installing holes on the desired
wall locus;
B Use an electric drill to make four holes for M6 screws on the above-drawn positions, and
drive in the special M6 screws;

C Push the power cable, communication cable and video cable through the bracket tube,
leaving long enough cables for connection;
D Fix the bracket firmly on the wall with three M5 screw nuts and washers.
或200
出线槽
Installation of high Speed Dome Camera
a. Unpacking the carton and carefully take out the dome camera and its attachments, open
the vitreous cover and take out the fillings.
b. Loosen the M3 screws connecting the camera and the outer housing, and swivel the camera
left for 15 degrees and remove it. Check cable connectors and see if any of them loose and setup
the coding switch.
c Restore the plastic washer to the camera, then tighten the installation of camera and outer
housing according to the installation instructions of the camera;
d. Insert the connecting cables into the bracket tube, then push the tube screw on the top of
the outer housing into the suspending bracket, fix it on the bracket with 3 M6 screws.
Connection of Exterior Cables
Connect BNC video outlet of the dome camera with the already disposed video cable, the
power cable with the already disposed power cable (DC14V) and RS485 controlling cable with
already disposed RS485 controlling cable. The signal cable of high speed dome camera is shown
below:
Cable
Application
Connecting Objects
Remarks
Power
cable
DC14V or
AC24V power
supply
high speed dome-power
supply adapter
green, white
485
cable
485 controlling
signal
high speed dome -
controlling device
red（A）、black（B）
Video
Camera signal
Camera-monitoring device
BNC connector
400 or 200
Cable slot

Cable
5-core
cable
Alarm input
Detector ---- high speed
dome
Black(alarm input
public port)
Yellow(channel 1
alarm input)
Green(channel 2
alarm input)
Blue(channel 3 alarm
input)
White(channel 4
alarm input)
2-core
cable
Alarm output
High speed dome ----
alarm horn
Brown(alarm output
pulic port)
Grey(alarm output
usually open output
port)
◆Make sure the polarity of RS485 controlling cable connection is correct, A: RS485
positive, B: RS485 negative.
◆If wrongly connected, the dome camera will be out of control.
Switching on Power
a Make sure the polarity of plugs, sockets and cables connection is correct, then switch on
power
b The dome camera begins to do the self-check by moving pan 360°, tilt 90° to check the
camera lens, the electrical and mechanical structures in pan/tilt state, then executing the
restoration program and resuming its original position. After the dome camera stops
moving, it finishes self-check and is ready to receive controlling instructions
c Use controlling device to control the dome camera, checking whether it can perform dome
and camera lens functions. If not, please check setups of communication protocol, Baud
rate and address, and connection of 485 controlling cable.
Vitreous Cover Installation
a To avoid scraping the vitreous cover, please clean the dust and stain on it with soft cloth;
b Aim the four screw holes in the vitreous cover at those in the outer housing, and fix it with
four M4 screws.
Vitreous Cover Installation
a To avoid scraping the vitreous cover, please clean the dust and stain on it with soft cloth;
b Aim the four screw holes in the vitreous cover at those in the outer housing, and fix it with
four special screws.

Socket for heater
Alarm input
Alarm output
Video -
Video +
485 +
485 -
Power +
Power -
Image amplified
12
6 5 34 2 1
6. Control high Speed Dome Camera by Keyboard
Intelligent control and all of its functions can be realized through the keyboard‟s control of
dome camera. Because different controlling system interfaces may differ in operation, operation
details are subject to the related manufacturer‟s manuals. Under certain circumstances of special
requirements and operations, please refer to dealers for necessary information.
6.1 Setup and Preview Preset Positions
The function of preset positions works in this way: the dome camera saves the current
pan/tilt parameters in number order (1-128), quickly previews those parameters when needed,
and adjust the dome to the corresponding positions. Users can use such devices as controlling
keyboard to save and preview preset positions fast and conveniently. The dome camera can
support 128 preset positions.
6.1.1 Setup the Preset Positions
After adjusting the dome camera to optimal state (including position, lens, focus and
aperture), enter the number(1～128) for preset position number, meanwhile, LED displays the
preset position number. Then press the “PRESET” key. If LED displays the address again, you
have setup the preset position successfully.
Example: Setup preset position No.1
a. Use the joystick to move the dome camera to the desired position and adjust the camera
lens.
b. Enter “1”
c. Press the “PRESET” key
◆Manual focus approach can be adopted to setup preset positions for distant objects, that
is, setup optimal focal image storage through the keys “FOCUS+”and “FOCUS-”on
the controlling keyboard to avoid fuzzy images resulting from the interference of other
distant objects.
6.1.2 Preview Preset Positions
Alarm input
Alarm output

The function enables the dome camera to quickly return to the preset position.
Enter the number(1～128) key for preset position number which you need preview, and
LED displays the preset position number. Then, press the “PREVIEW” key. The dome camera
will return to the preset position.
e.g. Preview the No.1 preset position
a. Enter “1”
b. Press “PREVIEW” key
6.2 Automatic Tour of high Speed Dome Camera
Remarks: “PELCO-D” protocol has no corresponding orders for part of the special
functions, so we converted functions of some of the commonly-used orders, generally converting
in the way of “preview preset position/ setup preset position”. Order conversion correspondence
is shown in the following table:
Preview
preset
position No.
Keyboard operation meaning
Preview
preset
position No.
Keyboard operation meaning
130
Setup left position
138
Stop dome auto-scanning
131
Setup right position
140
Start tour setup
132
Start linear scanning (low
speed)
141
Exit tour setup
133
Start linear scanning (high
speed)
142
Running a tour
134
Start linear scanning (high
speed)
145
Enter menu
135
Start dome 360º scanning
（low speed）
146
Exit menu
136
Start dome 360º scanning (high
speed)
162
Enter default position
137
Start dome 360º scanning (high
speed)
163
Exit default position
147
Open alarm function
148
Close alarm function
150
High speed dome camera
position restoration
164
Setup default position
Automatic tour is the important function of the dome camera, and the user can operate to
setup any tour route. With only one external order, the dome camera will automatically run a tour
following the designated route.
6.2.1 Setup of Tours
a. In the keyboard initialization, enter number “140” and press the “PREVIEW” key to enter the
tour setup.
b. After entering the setup, add preset position number to the tour. Enter the first desired preset
position number and press the “PREVIEW” key, and the first preset position is