RACK IT UP Riddick MPO SS User manual

THANK YOU VERY MUCH!
We sincerely appreciate your purchase of this exclusive kitchen/cookware storage product made by
RACK IT UP!
This pot rack is strong and easy to assemble. It is also the easiest ever to install with new-technology
DRYWALL anchors! We want you to enjoy it for many years to come. Please don’t hesitate to contact
us if you have questions or need assistance.
IMPORTANT!
We are committed to the highest quality in the manufacture of this pot rack. Each product has been care-
fully inspected before shipment.
However, in case there is a problem, PLEASE LET US HELP YOU FIRST. Do not return the item to the
location where you purchased it. Call us and explain what is missing or wrong. We will do our best to help
with any question or problem you have—and as fast as possible.
1 Year Limited Warranty
Call us TOLL FREE 1 [phone] and ask for customer service. Thank you!
Riddick Ceiling Rack
Ov P Rack—MPO SS

TIP! SAVE TIME AND HASSLE. PLEASE READ ENTIRE INSTRUCTIONS BEFORE BEGINNING ASSEMBLY.
ALL TOOLS NEEDED FOR
ASSEMBLY ARE PROVIDED-
Hex wrenches and
Fastener hardware (nuts, bolts)
STEP 1: LAYOUT PARTS
On a table lay out all parts as shown in the exploded view above.
STEP 2: CONNECT MAIN BODY PARTS
Temporarily connect two oval ends (4A) and two side bars (3A) by inserting a barrel nut and bolt (28A, 28B) through the
top hole at each of four corners. This will cause body of pot rack to stand on edge. Be certain side bars (3A) are on the
INSIDE when connected.
TIP! It is easiest to attach the pot rack parts when you insert the barrel nut (28B) from the INSIDE of the pot rack body,
then screw the barrel bolt (28A) into barrel nut (28B) from the OUTSIDE.
How to Assemble Your Pot Rack
MISSING A PART?
Please call our TOLL FREE
SERVICE CENTER
1 [phone]
TIP! FIRST, REMOVE PAINT FROM BARREL BOLT HOLES. Because the powder coat finish applied at
the factory also adheres to the inside of bolt holes, pushing a bolt through it during assembly may be diffi-
cult. Therefore, before connecting parts, we recommend that you check to see that bolts slip easily through
all holes. If they do not, carefully clear paint from holes in side bars, ends and arms using a small knife.
SECOND, be certain that barrel nuts and bolts screw together easily BEFORE beginning assembly. Resi-
due from the black finish may cause some bolts to stick a bit, therefore use the two hex wrenches enclosed
(one for each end of the barrel) and screw them together to clear away extra paint.
Item No. Description Qty. Item No Description Qty.
3A Side bar 22” 4 thru holes 2 25B Pot hook angled 6
4A Oval end 2
Installation Hardware
5 Hang tab 2 15 1" S-hook 2
6 Curved arm 4 17 Trim Ceiling Cover 2
7D Grid Bracket 4 31X Flange Nut for Trim Cover 2
8E Oval Grid 12" x 32" 1 19A 1/4" x 4" Bolt Hook 2
28A Barrel Bolt 11 20 Wood Screw Hook - 4" 2
28B Barrel Nut 11 26A 1/4" Hex Wrench 2
25A Pot hook straight 6 27A 1/4" Toggle 2
31X

STEP 3: ATTACH FIRST ARM
TIP! It is easiest to attach arms when the corner of the pot rack to which you are connecting the arm hangs slightly past the
edge of the table. That provides clearance for the flared end that extends below the body of the rack.
Now remove the barrel bolt (28A) from one of the corners, keeping barrel nut (28B) in position. Place a curve arm (6--two-hole
end) on the OUTSIDE of the oval ends. Align the three pieces over the barrel nut [side bar (3A) on inside, oval end (6) in mid-
dle, arm (4A) on outside] then screw the barrel bolt (28A) into nut and loosely tighten.
Repeat for lower hole. Do not tighten barrel bolts firmly until all bolts are in place.
STEP 4: ATTACH OTHER THREE ARMS
Repeat STEP THREE for remaining arms.
STEP 5: HANG TABS
Position two hang tabs (5) at tops of each arm pair, insert barrel nuts/bolts and loosely tighten.
STEP 6: LEVEL POT RACK ON TABLE
Place assembled rack squarely on table and adjust all parts to be certain they are level and straight. Then tighten all bolts firm-
ly.
STEP 7: PLACE BRACKETS AND GRID
Evenly space the four grid brackets along the rim of the rack inside the arms as per illustration on page 2 of these instructions
and lay the grid across the brackets.
MISSING A PART?
Please call our TOLL FREE
SERVICE CENTER
1 [phone]
How to Attach Your Pot Rack to the Ceiling
TOOLS NEEDED:
Provided: Installation hardware (anchors, bolt hooks, screw hooks, S-hooks)
You will need: tape measure, pencil, drill and ½” drill bit, hammer and nail
STEP 1: LOCATION
Decide where you want to place your pot rack. We suggest placement over an island or near your stove and food preparation
area. Also consider the height of the ceiling where the pot rack will hang. (See STEP 2 below.)
On the ceiling, mark two points 20-3/4” apart where the top of rack arms (at hang tabs) will attach to ceiling bolt hooks. Then
tap a small nail through each mark to be certain a joist is not in the way. (NOTE: because your pot rack includes super-strong
new-technology anchors, you DO NOT need to locate and bolt to ceiling joists. See more info under STEP 3 below.)
STEP 2: HEIGHT
What is the ideal height for your pot rack? Decide who will be the primary cook using the pot rack. The bottom of your longest
pan (usually a 10” or 12” skillet) should be easily reachable, about 6 inches above the cook’s head. Make sure the cook can
also reach the shortest pots.
This pot rack is designed for a 9-foot ceiling, a common height in many kitchens. If your ceiling is HIGHER than 9 feet, you
may want to consider adding chain to lower the rack to the ideal height. (Buy chain at a hardware store or contact our Custom-
er Service department.)
STEP 3: INSTALL DRYWALL ANCHORS
These new-technology DRYWALL anchors eliminate the need to bolt your pot rack to a ceiling joist. The steel anchors are very
strong and when installed in 5/8” drywall (standard ceiling code in modern houses) each drywall anchor holds about 200 lbs.
Two anchors hold about 400 lbs., many times the weight you will likely hang from your pot rack. Since you no longer have to
consider the location of a joist which usually determines where your rack has to be installed, you can position it in drywall any-
where you want!
Note: If you need to install your rack into wood ceiling joints, use the two wood
screw hooks provided instead of the drywall anchors and bolt hooks.

TOGGLER® brand SNAPTOGGLE® Toggle Bolt Installation Instructions
DO NOT attempt to test the snaptoggle as you will be unable to use it. Should
you need additional snaptoggles, you may purchase them at Lowes or find a lo-
cal resource on toggler.com
IMPORTANT! If your house is older (maybe a Victorian?) with lath board plaster ceilings and walls, DO NOT use the
new drywall anchor system. Old lath board plaster walls are not strong enough to hold drywall anchors. You must at-
tach the pot rack to wood joists with 4” wood hook/screws (included with your pot rack).
1) Using an electric drill with ½” bit, drill a hole at each of your marked
points. Hold metal channel flat alongside plastic straps
and slide channel through hole. Minimum clearance behind ceiling
should be 1 ⅞”.
NOTE: If a wood joist happens to be located at one of those points, use one of
the
4” wood screw hooks provided and screw it into the joist. (Pre-drill a hole in the
joist so the hook is easier to screw into the hole.)
We also understand--if you prefer, you can use the two wood screw hooks pro-
vided and drive them into the joists so you’re confident with the strength of the
attachment. However, to do so will likely require placing a cross bar (not includ-
ed)
above the ceiling which will often necessitate a carpenter’s services.
2) Hold ends of straps between thumb and forefinger and pull toward you until
channel rests flush behind drywall. Slide plastic cap along straps with other
hand until flange of cap is flush with the ceiling.
3)Bend straps at ceiling by pushing side to side, snapping
off straps level with flange of cap.
4) Insert screw hook and tighten until flush, then stop.
NOTE: If you are also installing Trim Ceiling Covers (a RACK IT UP accessory), see pack-
age instructions before inserting and tightening bolt/hook.
Toggler ® Independent Lab Results
(anchor load before failure per attachment point)
TENSILE SHEAR
½” drywall - 265 lbs. ½” drywall - 241 lbs.
⅝“ drywall - 356 lbs. ⅝” drywall - 324 lbs.
Industry safety standards recommend ¼ of ultimate test load
That’s’ it – You are now ready to hang your new pot rack!
Ceiling
Installation of Drywall Anchors
U.S. Patent no. 6, 161,999 and foreign counterparts thereof and of 4, 650, 386. Other patents pending. TOGGLER and SNAPTOOGLE are worldwide registered trademarks of Mechanical plastics Corp