RACK IT UP MPW-09 User manual

IMPORTANT!
Enclume Design Products is committed to the highest quality in the manufacture of this RACK IT UP! pot rack.
The components of each rack are carefully inspected before shipment.
However, in case there is a problem, PLEASE LET US HELP YOU FIRST. Do not return the item to where you
purchased it. First, call us and explain what is missing or wrong. We will do our best to help with any question or
problem you have—and as fast as possible.
Call us TOLL FREE 1 [phone] and ask for customer service. Thank you!
Wall Bar & Wood Shelf
MPW-09
RACK IT UP! 5-Year Limited Warranty
This product is warranted to be free of material defects for a period of five years from the date of purchase. Your exclusive
remedy is the repair or replacement of the defective product, and shall be subject to the following conditions: (1) You send
a notice of any defect to Enclume within the warranty period, and (2) You return the defective product, to Enclume
Design Products, 24 Colwell Street, Port Hadlock, WA 98339, postage prepaid, within 20 days following receiving a
return authorization number. (A return authorization number may be obtained from Enclume by calling the number at the
bottom of this booklet.) There are no other warranties expressed or implied. There are no warranties of merchantability or
fitness for a particular purpose. Enclume specifically disclaims any and all incidental or consequential damages arising out
of purchase, installation or use of this product.
RACK IT UP! ™ is a trademark of Enclume Design Products
All rights reserved. Made in China. Packed in the U.S.A.
TOOLS NEEDED -
We provide all tools required for assembly (except drill for predrilling wood shelf), hex wrench, and fastener
hardware (nuts, bolts). Note under attaching instructions on page 3 of this booklet, the list of tools you will need
to provide (plus 1/8"drill bit for wood shelf).

TIP! SAVE TIME AND HASSLE. PLEASE READ ENTIRE INSTRUCTIONS BEFORE BEGINNING ASSEMBLY.
PAINTABLE - Want a different color? The finish on this pot rack can be spray painted any color. We
recommend Rustoleum “Hammered” colors for their metal-like finishes, however any quality spray-can paint may be
used. See a paint retailer for guidance.
WOOD SHELF is coated with wood oil to enhance the grain and minimize warping due to humidity fluctuations. We
recommend that it remain “natural.”
TOOLS NEEDED - Hex wrench, fastener hardware (nuts, bolts) are provided.
STEP 1: LAYOUT PARTS
On a table lay out all parts as shown in the exploded view above.
STEP 2: LOCATE BRACKET ON BAR & SECURE
Note the small hole near the end of the side bar (3C) Place a bracket (12) over the hole to cover it, then slide the brack-
et back and forth (an inch or so either direction, keeping the hole covered) until you have determined for yourself the
most pleasing distance from the end of the bar. Mark that distance, then with button head bolts (18A) secure the other
bracket at the same point from its end.
How To Assemble Your Pot Rack
TIP! FIRST, CLEAR PAINT FROM SCREW HOLES. Because the powder coat finish applied at the
factory also adheres to the inside of screw holes, turning a screw through it during assembly may be difficult.
Therefore, before connecting parts, we recommend that you clean out screw holes in brackets (12). Using a
button head screw and hex wrench provided, rotate the bolt through each screw hole, then withdraw it. That
will push paint out and make securing parts easier.
Item No. Description Qty. Item No Description (Hardware bag contents) Qty.
3C Wall/Ceiling bar 1 18A Button head screw - 1/4” 2
12 Wall bracket 2 19C Button head bolt - 2” 2
29 Wood 22” x 3.5” 1 18E 1/2” wood screw #8 2
25A Pot hook straight 4 26A Hex wrench 1
25B Pot hook angled 4 30A Wall Screw 2
27A Toggle 2
MISSING A PART?
Please call our TOLL
FREE SERVICE CENTER
1 [phone]

STEP 3: SQUARE POT RACK ON TABLE
Place assembled rack squarely on table and adjust all parts to be certain they are level and straight. Then tighten all bolts
firmly.
Now measure the distance between holes center to center at tops of brackets and note for later use when you install (see instal-
lation instructions below).
STEP 4: POSITION WOOD SHELF
Note the small holes located in the center of the flat section of each bracket. Two set screws (18E) will be driven through them
to secure the Wood shelf to the brackets.
Center the Wood shelf on top of the brackets (now fixed in position) then with a pencil mark the two set screw points on the un-
der side of the bracket. Pre-drill the marks with a 1/8"drill bit (or tap a starter hole with a hammer and a small nail) then drive
set screws (18E) into Wood to secure shelf.
You’re now finished and ready to attach to the wall!
TOOLS NEEDED FOR INSTALLATION:
Provided: Installation hardware (anchors, bolts, and wall screws)
You will need: level, tape measure, pencil, electric drill, ½"drill bit, hammer and nail.
STEP 1: LOCATION
Decide where you want to place your pot rack. Consider the height of the wall where the pot rack will hang, keep-
ing in mind how far below the rack your pots and utensils will hang.
On the wall, mark the two points where you would like to hang the rack, then tap a small nail through each mark to
be certain a joist is not in the way. NOTE: because your pot rack includes toggle anchors, you DO NOT need to
locate and bolt to studs. See more information under STEP 2 below.
STEP 2: INSTALL TOGGLER® DRYWALL ANCHORS
The included drywall Toggles eliminate the need to bolt your pot rack to a stud. The steel anchors are very strong
and when installed in drywall each drywall anchor holds about 100 lbs. Two anchors hold about 200 lbs. Install the
two Toggle drywall anchors (27A) where the two holes in the tops of the two bookshelf arms are located. Carefully
follow Steps 1 through 4 of the Toggle Drywall Anchor instructions found on the back of this booklet.
INSTALL IN WOOD?
If you need to install one or both sides of your rack in wood, use as many of the two wall screws (18E) included to
meet your needs.
How to Attach Your Pot Rack to the Wall

Wall Bar & Wood Shelf
Installation of Drywall Anchors
TOGGLER® brand SNAPTOGGLE® Toggle Bolt Installation Instructions
DO NOT attempt to test the snaptoggle as you will be unable to use them. Should
you need additional snaptoggles, you may purchase them at Lowes or find a local
resource on toggler.com.
IMPORTANT! If your house is older (maybe a Victorian?) with lath board plaster ceilings and walls, DO NOT use the new
drywall anchor system. Old lath board plaster walls are not strong enough to hold drywall anchors. In this case, you must
attach the wall rack to wood studs with wood lag screws (included with your
rack).
1) Using an electric drill, drill a ½” hole at each of your mounting points.
Hold metal channel flat alongside plastic straps and slide channel
through hold. Minimum clearance behind wall should be 1 ⅞”.
NOTE: If a wood stud happens to be located at one of those points, use
The included wood lag screw (18E) and screw it into the stud.
(Pre-drill a 3/16” hole in the stud so the screws are easier to screw
into the hole).
2) Firmly push plastic cap up along guide straps with other hand.
Press cap inside the hole, so flange is flush with drywall surface.
3) Bend straps at wall by pushing side to side, snapping off straps level with
flange of cap.
4) Align mounting holes and insert screw (30A) through each hole and
tighten.
That’s It! You are now ready to hang your pots & utensils!
U.S. Patent no. 6, 161,999 and foreign counterparts thereof and of 4, 650, 386.Other patents pending. TOGGLER and SNAPTOOGLE are worldwide registered trademarks of Mechanical plastics Corp
MISSING A PART?
Please call our TOLL FREE
SERVICE CENTER
1 [phone]
Toggler ® Independent Lab Results
(Anchor load before failure per attachment point)
TENSILE SHEAR
½” drywall – 265 lbs. ½” drywall – 241 lbs
5/8” drywall – 356 lbs. 5/8” drywall – 324 lbs.
Industry safety standards recommend ¼ of ultimate
test load.