Radiant TS8100-TH-H User manual

The buttons are locked
Turning on/off the thermostat
Heating is turned on
Automatic mode, executes the programmed schedules
The sensor is not being read by the thermostat
Err
Temporary temperature override
Frost protection activated
Room temperature
RT
AUTO
Floor temperature
FT
O / RIDE
Symbols
The program number
Day of the week. Day 1= Monday, Day 2= Tuesday... etc.
Reminding the user to connect the floor sensor (AF and F model only)
Touch to view floor temperature for 5 seconds (AF model only)
Touch to switch among Auto
Touch to start programming of your thermostat
Comfort temperature mode
Economy temperature mode
Day
Program 1,2,3,4
Vacation temperature mode
Symbols Description
Description
Set
Schedule
Heating
Mode
TS8100-TH-H Thermostat Instructions
ver 1.2
LCD symbols
Configuration Menu
To enter into the setting menu please follow the steps below:
Step 1, Turn the thermostat off by pressing ;
Step 2, Press , you will then see menu 01.
Step 3, Use the up and down arrows to adjust the “sensor selection” which is Menu 01(Air sensing, Air and Floor, or Floor only)
Step 4, Press
to move to the next Menu and once you have all the menu options set,
Setp 5, Press to accept and store.
Menu # Feature Explanation Adjustment（press up & down buttons to adjust）
01 Mode/Sensor selection
This thermostat is a combination model which allows you to
choose 3 different modes.
A mode=Air Sensing Only(Has built in sensor)
AF mode=Air & Floor sensing(Floor probe must be installed)
F mode=Floor Sensing(Floor probe must be installed)
A, AF, F
02
03
Maximum Floor Temp
( AF mode only) This is to protect the floor surface. 20 °C~ 40 °C (40 °C by default)
5+2 / 7 Day Mode This allows you to program either 5 days at once, then the 2
days of the weekend separately, or a full 7 days at the same
time or 7 days separately
01 = 5+2 day programmable
02 = 7 day programmable
Setting the clock and day of the week
NEXT
MENU
POWER
DONE
Select the required operating mode
This thermostat is fitted with a real time clock. It is essential that the clock time and day are set accurately if you require your programmed events to start on time. Follow below steps,
1) Touch time display.
Auto - Automatic mode, the thermostat executes the preprogrammed schedules. To adjust these schedules, see page 2 the program section.
In addition to Automatic mode, this thermostat has 3 extra manual modes, i.e , each of these manual modes maintains a constant set temperature set by the user.
- Comfort temperature mode, the highest temperature you want to achieve, this is the temperature that will be required when the room is in use. Default is 22 °C.
- Economy temperature mode, the lowest temperature, the temperature you want to go no lower than when the room is not in use. Default is 16 °C.
- Vacation temperature mode, this is set to stop your floor from going below the set temperature. Default is 10 °C.
To change the set temperatures, touch temperature display. Use or to adjust to the required temperature. Touch to store and exit.
2) Touch day display .
Use or to change the time. Press and hold
Use or to change the day. Touch to store and exit. (or touch Day display to cancel and exit).
or to change the time faster. Touch to store and exit( or touch time display to cancel and exit).
Done
Done
Done
The buttons are locked
Turning on/off the thermostat
Heating is turned on
Automatic mode, executes the programmed schedules
The sensor is not being read by the thermostat
Err
Temporary temperature override
Frost protection activated
Room temperature
RT
AUTO
Floor temperature
FT
O / RIDE
Symbols
The program number
Day of the week. Day 1= Monday, Day 2= Tuesday... etc.
Reminding the user to connect the floor sensor (AF and F model only)
Touch to view floor temperature for 5 seconds (AF model only)
Touch to switch among Auto
Touch to start programming of your thermostat
Comfort temperature mode
Economy temperature mode
Day
Program 1,2,3,4
Vacation temperature mode
Symbols Description
Description
Set
Schedule
Heating
Mode
LCD SYMBOLS
CONFIGURATION MENU
SELECT THE REQUIRED OPERATING MODE
TS8100-TH-H THERMOSTAT INSTRUCTIONS
See overleaf for further instructions >>>
SETTING THE CLOCK AND DAY OF THE WEEK
Radiant Australia Pty Ltd Unit 1 / 18 Profit Pass, Wangara, WA 6065
Telephone: [phone] Fax: [phone] Email: [e-mail]

Setting the Program Schedules
Lock the Keypad
To lock the keypad, press and hold the top left corner of display for 5 seconds, you will see
a lock symbol . To unlock, repeat the steps above and the lock symbol will disappear.
Reset to Factory Setting
With thermostat turned off, press and hold OFF for 5 seconds until you can see -- : -- on LCD.
Temporary Temperature Override
Touch the temperature display, and it will start to flash. Use up or down buttons to adjust.
Press to accept, and you will see“Override”above the temperature display.Thermostat
will maintain the new set temperature until the next programmed event(comfort level).
To cancel the override setting, press
RUN
SCHEDULE
Installation and Wiring
Carefully separate the front half of the thermostat from the back plate by placing a
small flat head terminal driver into the slots on the bottom face of the thermostat.
Carefully unplug the ribbon connector which is plugged into the front half of the
thermostat. Place the thermostat front half somewhere safe. Terminate the thermostat
as shown in the diagrams below.
Screw the thermostat back plate on to the flush box.
Re-connect the thermostat ribbon cable and clip the two halves together.
This product should be installed by
a qualified electrician.
TS8100-TH-H Thermostat Instructions
ver 1.2
DONE
This thermostat can be individual 7-day programmable. For each day of the week you are able to have 4 timed set temperature schedules.
Above are default program schedules, to make changes, follow easy steps as below.
Set to the time you would like to wake to and the temperature you want during the morning, until you left for the day.
Set to the time you leave home and the temperature you wish your home to maintain while you are away at work perhaps.
Set to the time you return home at end of the day and the temperature you want during evening until bed time.
Set to the time you sleep and the temperature you want overnight (usually a comfortable and energy saving temperature).
07:001
2
3
4
22 °C
16:30 22 °C
09:30 16 °C
22:30 16 °C
WAKE
Program Start Time Setpoint Explanation
LEAVE
RETURN
SLEEP
Press , you will see day display flashing.
Use or adjust the day to the day you wish to start programming
Press , the LCD will show program 1 with the time display flashing.
Use or adjust the time you wish the program 1 event to
commence for the currently selected day or days.
Press , the LCD will show a temperature value flashing.
Use or set the desired heating temperature to be maintained
Press , now the LCD will show program 2 with the time display
Repeat step 4,5,6 to set remaining programs. Press to store and exit.
During setting programs, press (if visible) will clear a program entry
1.
2.
3.
4.
5.
5.
6.
6.
7.
8.
(Press to select all days of the week, to cancel selecting all days of
DONE
DONE
All Days
All Days
Set
Schedule
Next
Next
Next
Next
Next
Next
Delete
program until the beginning of the next program.
Note: It is faster to program the same schedule for the entire week
and then to adjust the exceptional days.
Set time and temperature for the next time period(Leave). Repeat steps
2 and 3 for each time period of the weekday.
In 7 day program mode In 5+2 day program mode
NOTE:
flashing, signifying the second daily event is now being programmed.
for the program 1 event.
the week, press again.)
or to the day you wish to edit an existin
g event or program.
Press , you will see the time flashing.
Press to move to the weekend(sat-sun) time periods settings.
Use or to set your weekday Wake time(Mon-Fri), then press
1.
2.
3.
4.
Use or to set the temperature for this time period, then press
Set
Schedule
Press to save and exit.
Day 1 - 5, refers to the weekday( Monday to Friday)
Day 6 - 7, refers to the weekend( Saturday and Sunday)
and thermostat will maintain the temperature setpoint of the last executed
SETTING THE PROGRAM SCHEDULES
Radiant Australia Pty Ltd Unit 1 / 18 Profit Pass, Wangara, WA 6065
Telephone: [phone] Fax: [phone] Email: [email protected]
LOCK THE KEYPAD
RESET TO FACTORY SETTING
TEMPORARY TEMPERATURE OVERDRIVE
INSTALLATION AND WIRING