Ransomes Matador Guide

®
RJL 100 September 2014
GB
United
Kingdom
Safety, Operation & Maintenance Manual
Ransomes MATADOR 71 - Engine HONDA GX160-K1
Series: EH4
Product code: LDDD704
WARNING
WARNING: If incorrectly used this machine can
cause severe injury. Those who use and maintain
this machine must be trained in its proper use,
warned of its dangers and must read the entire
manual before attempting to set up, operate, adjust
or service the machine.
25068G-GB (R1)

1 CONTENTS
© Ransomes Jacobsen Limited. All Rights Reserved
INTRODUCTION
IMPORTANT ........................................................................................... 3
PRODUCT IDENTIFICATION ...................................................................... 4
GUIDELINES FOR THE DISPOSAL OFSCRAP PRODUCTS ......................... 6
DURING SERVICE LIFE ........................................................................... 6
END OFSERVICE LIFE ........................................................................... 6
PARTS MANUAL ..................................................................................... 7
KEY NUMBERS ...................................................................................... 7
SAFETY HOW TOOPERATE SAFELY..................................................................... 9
SAFE OPERATION .................................................................................. 9
PREPARATION ...................................................................................... 10
OPERATION .......................................................................................... 11
MAINTENANCE AND STORAGE ............................................................... 12
IMPORTANT SAFETY NOTES .................................................................. 12
SPECIFICATION
ENGINE SPECIFICATION ........................................................................ 17
DIMENSIONS & WEIGHTS ...................................................................... 18
MACHINE SPECIFICATION ...................................................................... 18
VIBRATION LEVEL ................................................................................. 20
NOISE LEVEL......................................................................................... 20
SLOPES ............................................................................................... 20
CUTTING UNIT SPECIFICATION .............................................................. 21
CUTTING PERFORMANCE ...................................................................... 21
RECOMMENDED LUBRICANTS ................................................................ 21
ACCESSORIES ...................................................................................... 21
AIR SUSPENSION SEAT KIT ................................................................... 21
CERTIFICATES OFCONFORMITY............................................................. 22
DECALS SAFETY DECALS EC ............................................................................. 27
INSTRUCTION DECALS EC .................................................................... 28
CONTROLS
OPC .................................................................................................... 29
LANDROLL CLUTCH................................................................................ 29
THROTTLE CONTROL LEVER ................................................................. 30
PARKING BRAKES ................................................................................. 30
CYLINDER CLUTCH................................................................................ 30
CUT OUT SWITCH ................................................................................ 31
OPERATION
DAILY INSPECTION ................................................................................ 33
OPERATOR PRESENCE AND SAFETY INTERLOCK SYSTEM ...................... 33
PROCEDURE FOR OPERATION .............................................................. 33
OPERATION OFTHE MACHINE .............................................................. 34
BEFORE YOU OPERATE, FOR THE FIRST TIME ...................................... 35
HOW TOSTART THE ENGINE ................................................................ 36
TOSTOP THE ENGINE .......................................................................... 37
GOOD OPERATION ................................................................................ 38
ADJUSTMENTS
HEIGHT OF CUT SETTING ...................................................................... 39
HEIGHT OF CUT ADJUSTMENT ............................................................... 39
FRONT ROLL ALIGN .............................................................................. 40
BLADE ADJUSTMENT ............................................................................. 40
CLUTCH ADJUSTMENT .......................................................................... 40
LANDROLL CLUTCH ADJUST .................................................................. 41
LANDROLL SCRAPER.............................................................................. 42
CHAIN ADJUSTMENT.............................................................................. 43
BACKLAPPING........................................................................................ 43
HANDLE ADJUSTMENT ........................................................................... 44
PARKING BRAKE.................................................................................... 45
ACCESSORIES
TRAILING SEAT...................................................................................... 45
MAINTENANCE
DAILY.................................................................................................... 47
WEEKLY................................................................................................ 48
CLUTCH AND LANDROLL ........................................................................ 49
LUBRICATION
DAILY.................................................................................................... 51
BEFORE FIRST USE .............................................................................. 52
QUALITY OF CUT PROBLEM SOLVING
WASHBOARDING.................................................................................... 53
MARCELLING ......................................................................................... 54
STEP CUTTING...................................................................................... 55
SCALPING ............................................................................................. 55
STRAGGLERS ........................................................................................ 56
STREAKS .............................................................................................. 57
WINDROWING........................................................................................ 57
RIFLING ORTRAM-LINING ...................................................................... 58
MISMATCHED CUTTING UNITS................................................................ 60
GUARANTEE
GUARANTEE ......................................................................................... 61
SECTION...................................................................................................PAGE SECTION....................................................................................................PAGE

en-3
INTRODUCTION 2
2.1 IMPORTANT__________________________________________________________
The Ransomes MATADOR is a Petrol engined Pedestrian REEL mower. The traction drive and the cutting unit
are Chain Driven.
IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high
level.
This SAFETY AND OPERATORS MANUAL is part of the machine and must stay with the machine always.
Suppliers of both original and used machines need to keep the documentation that comes with the machine.
You must use the machine to cut the grass only and not for any other purpose. Compliance with the conditions of
operation, service and repair specified by the manufacturer, are understood to be part of the correct use.
ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and
maintenance procedures.
Make sure that you obey all safety and road traffic regulations.
You must not make any changes to the machine that the manufacturer does not approve. This type of change
can release the manufacturer from the liability for any damage or injury.
Discard worn parts, taking note of the environmental result, use the systems available in the country where the
machine is used. When the machine is at its end of life, there are guidelines in this manual for the removal of the
machine from use.
Use only Ransomes Jacobsen Genuine spare parts to make sure that European conformity is controlled.
2006/42/EC
These instructions are the Original instructions confirmed by Ransomes Jacobsen Limited

en-4
2 INTRODUCTION
2.2 PRODUCT IDENTIFICATION ___________________________________________
A Maximum front axle load in Kg (for machines being driven
on the highway)
B Gross weight (mass) in Kg
C Maximum rear axle load in Kg (for machines being driven on
the highway)
D Power in Kw
E Date code
F Machine type (Designation)
G Product code
H Product name
J Serial number
Location of Serial number plate
The serial number plate (A) is found on the chassis side plate.
Location of Engine Serial number plate
The engine serial number is found on the engine next to the Oil level dipstick.
Kg Kw Kg Kg
West Road
Ransomes Europark
Ipswich IP3 9TT
England
ABCD E
FG
HJ
Kg Kw Kg Kg
WestRoad
RansomesEuropark
IpswichIP39TT
England
AC
WA
100
dB
L
B
XXXX-XXXX_XXXX

en-5
INTRODUCTION 2
2.3UIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS ______________________
2.3.1 DURING SERVICE LIFE _______________________________________________
Used oil, oil filters and engine coolant are hazardous materials. Recommended procedures must be followed for their
safe removal.
If a fluid leaks, contain the spill to make sure that the leak does not flow into the ground or drainage system. Follow the
local laws to make sure that leaks are controlled safely.
The maintenance procedures in this manual make sure that the damage that the machine can cause in the local
environment is controlled safely.
When the machine completes its full service life, the following actions must be taken.
2.3.2 END OF SERVICE LIFE _______________________________________________
These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the approved local
waste disposal and agencies for recycled materials.
• Park the machine in a location to use all of the necessary lifting equipment.
• Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical
manuals applicable to the machine.
• Remove and store correctly
1. Batteries
2. Fuel
3. Engine coolant
4. Oils
• Disassemble the structure of the machine and refer to the technical manuals where applicable. Give
attention to parts that have mechanical pressure or tension applied to the part in the machine, including
springs.
• Items that continue to have a service life must be separated and returned to the local store.
• Items that are worn must be separated into the material groups and removed according to the agencies
for recycled materials that are available. Common types are as follows:
• Steel
• Non ferrous metals
• Aluminium
• Brass
• Copper
• Plastic materials
• Identified
• Can be recycled
• Can not be recycled
• Not identified
• Rubber
• Electrical and Electronic Components
• If an item is not easily separated into different material groups, the material must be added to the
“General discarded materials” area.
• Do not burn discarded materials.
Change the machinery records to show that the machine is not in service and is discarded. Supply this serial number to
Ransomes Jacobsen Warranty Department to close their records.

en-6
2 INTRODUCTION
2.4 PARTS MANUAL ______________________________________________________
In compliance with the ISO14001 standard, Ransomes Jacobsen Limited does not send a paper parts manual
with every product.
To refer to a parts list for this mower you have four options:
1. Website – www.ransomesRansomes Jacobsen.com. Select the “GENUINE PARTS” tab followed by
the “ONLINE PARTS LOOK-UP” tab. You now have access to Parts drawings and lists to help with the
identification of spare parts.
2. Website – www.ransomesRansomes Jacobsen.com. Select the “SUPPORT” tab. You now have access
to a PDF version of the parts manual.
3. Complete the form included in the technical manual pack supplied with the machine for one of the two
options below
a. A disc that contains an electronic copy of the Parts Book.
b. A paper copy of the parts manual.
2.5 KEY NUMBERS _______________________________________________________
Record the key numbers shown below:
Starter Switch:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Diesel tank:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Record the machine and engine numbers shown below:
The machine serial number is found on the registration plate and the engine serial number can be found on the
rocker cover.
Machine Number:-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Engine Number:-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

en-7
INTRODUCTION 2
B
A
C
FIG 2
FIG 1
2.6 ASSEMBLY __________________________________________________________
The Mower is fitted to a container at the factory and will need assembly before operation. Some tools will be
needed for assembly. Discard the container according to the applicable local environmental requirement.
Remove the mower from the container. The
handles are found around the chassis - Figure
1.
The handles engage on the lug shaft (A). A
range of height adjustment is available.
Tighten the hand wheel (C) The handles
adjust for reach with the bolts (B) - Figure 2.
The Grassbox (A) - Figure 3 engages on the
mower by two lugs bolted to the chassis lug
(B).
Refer to the OPERATION Chapter before you
start the mower for the first time. Operators
MUST read through this manual and
understand the Safety Instructions, controls,
lubrication and maintenance procedures
before any use the Mower.
FIG 3
B

en-8
2 INTRODUCTION
NOTES

en-9
SAFETY 3
3.1 HOW TO OPERATE SAFELY_____________________________________________
3.1.1 Safe Operation
a Read the Operator’s Manual and other training material. If the operator or technician can not read this
manual, the owner is responsible to describe this material to the operators and technicians. Manuals in
additional languages may be available on the Jacobsen or Ransomes Jacobsen website.
a Read all of the instructions for this mower carefully. Know the controls and the correct operation of the
equipment.
b Children or persons who do not understand these instructions must not use the mower. The local
regulations can limit the age of the operator.
c Never use a mower near persons, including children or animals.
d Remember that the operator or owner is responsible for accidents or hazards that occur to other persons or
their property.
e Never carry passengers.
f Never allow persons to operate or service the mower or its attachments without correct instructions.
g Do not operate equipment while tired, sick or after you use alcohol or drugs.
3.1.2 Preparation
a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard
hat, safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving
parts.
b Do not operate the equipment with the Interlock System disconnected or the system does not operate
correctly. Do not disconnect or prevent the operation of any switch.
c Never operate equipment that is not in correct order or without decals, guards, shields, deflectors or other
protective devices fastened. When you mow with a side discharge deck, DO NOT operate the cutting unit
without the discharge chute installed.
d Inspect the mower before you operate the mower. Check the tire pressure, engine oil level, the radiator
coolant level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the
mower.
e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during
bad weather. Never operate the mower with lightning in the area.
f Inspect the area to select the accessories and attachments that are needed to correctly and safely do the
job. Only use parts, accessories and attachments approved by Jacobsen.
g Be careful of holes in the terrain and other hazards that are not visible.
h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be
careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles
(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.
i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you
rotate one blade, other blades can rotate.
WARNING
EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.
Know the location and correct operation of controls. Operators without experience must receive instruction
from another person that knows the correct operation of the equipment before you operate the mower.
Only use parts, accessories and attachments approved by Jacobsen.
!

en-10
3 SAFETY
3.1.3 Operation
a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the
exhaust fumes can increase to dangerous levels.
b Never carry passengers. Keep other persons or animals away from the mower.
c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with
the operator in the seat. Never start the engine with persons near the mower.
d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep
your hands and feet away from the cutting units.
e Do not use on the slopes greater than the safe slope limit for the equipment.
f To guard against over turning or loss of control:
– Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).
– Do not start or stop suddenly on slopes.
– Decrease the speed when you operate on slopes or when you must turn. Use caution when you change
direction. Turf condition can change the mower stability.
– Use caution when you operate the mower near drop-offs, ditches or embankments.
– Be careful of holes in the terrain and other hazards that are not visible.
g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not
operate the cutting units when you drive in the reverse direction.
h Use caution when you go near corners, trees or other objects that can prevent a clear view.
i Equipment must meet the current regulations to be driven on the public roads.
j Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and
travel at decreased speed. Look for traffic.
k Stop the blades when the mower is on any surface that is not grass.
l Do not release the cut grass in the direction of persons or allow persons near the mower while in operation.
m Do not operate the mower with damaged guards or without safety devices in position.
n Do not change the engine governor setting or over-speed the engine. Never change or tamper with
adjusters that are closed with a seal for the engine speed control.
o Before you leave the operator compartment, for any reason:
– Disengage all the drives and lower attachments to the ground.
– Engage the parking brake.
– Stop the engine and remove the key.
p When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for
damage and make repairs.
q Decrease the throttle setting before you stop the engine.
r Do not use this equipment for uses that the mower was not made for.

en-11
SAFETY 3
3.1.4 ROPS
a The ROPS is a safety device. Keep the ROPS in the vertical and locked position. Always use the seat belt
when you operate the mower. Make sure the seat belt can be released quickly in an emergency.
b Only operate the mower with the ROPS in the folded position on flat and level surfaces when necessary.
Do not operate the mower with the ROPS in the folded position on slopes, near sharp edges or near water.
There is no roll over protection with the ROPS in the folded position.
c Check for clearance before you drive below objects. Do not contact tree branches, electrical wires or other
objects with the ROPS.
d Do not use the seat belt with the ROPS in the folded position.
e Inspect the ROPS for damage. Keep the ROPS hardware fastened.
f Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged
ROPS.
g Do not remove the ROPS from the mower.
h Jacobsen must approve any changes to the ROPS.
3.1.5 Safe Handling of Fuels
a The fuel and the fuel vapors are flammable. Use caution when you add the fuel to the mower. The fuel
vapors can cause an explosion.
b Never use the containers that are not approved to keep or transfer fuel.
c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of
fuel or fuel vapors.
d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel
container on the ground away from your vehicle before you fill the container.
e Refuel the mower before you start the engine. When the engine is in operation or while the engine is hot,
never remove the fuel cap or add fuel to the mower.
f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.
g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to
lock the fuel nozzle in the open position.
h Do not over fill the fuel tank. Leave at least 1 inch (25 mm) below the filler neck.
i Always tighten the fuel tank cap and container cap after you add fuel.
j If the fuel spills on your clothing, change your clothing immediately.
3.1.6 Maintenance and Storage
a Before you clean, adjust or repair this equipment, push PTO switch to the OFF position, lower the cutting
unit to the ground, engage the parking brake, stop the engine and remove the key.
b Make sure the mower is parked on a solid and level surface.
c Never work on a mower that is lifted only by the jack. Always use the jack stands.
d Never allow persons to service the mower or its attachments without correct instructions.
e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a
positive mechanical lock is used.
When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near
flames or drain the fuel inside a building.
f Disconnect the battery before you service the mower. Always disconnect the negative battery cable before
the positive battery cable. Always connect the positive battery cable before the negative battery cable.

en-12
3 SAFETY
g Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To
prevent an explosion, keep any device that can cause sparks or flames away from the battery.
h Disconnect the battery charger from the power supply before you connect or disconnect the battery charger
to the battery. Wear protective clothing and use insulated tools when you service the battery.
i Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged
blades, do not try to correct a damaged blade.
j Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in
operation, unless the adjustment needs the engine in operation.
k Carefully release the pressure from components with stored energy.
l To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the paper
or cardboard to find leaks.
m The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your
skin, a doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.
n When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to
the correct torque. Make sure the hydraulic system is in good condition before you start the engine.
o Keep the mower and the engine clean.
p Allow the engine to become cool before storage and always remove the ignition key.
q Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.
r Replace worn or damaged parts for safety. Replace damaged or worn decals. Only use parts, accessories
and attachments approved by Jacobsen.
s To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank
area.
t Disconnect the battery and controller connectors before you weld on this mower.
3.1.7 When you Put the mower on a trailer
a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can
carry the weight of the mower.
b Use a full-width ramp to load or unload the mower on a trailer.
c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be
sent down and toward sides of trailer.
Make sure that all latches are correctly fastened.

en-13
SAFETY 3
3.1.8 Important Safety Notes
This safety alert symbol is used to alert you to possible hazards.
DANGER:
Indicates a dangerous condition that WILL cause death or injury unless it is prevented.
WARNING:
Indicates a dangerous condition that CAN cause death or injury unless it is prevented.
CAUTION:
Indicates a dangerous condition that can cause injury and property damage unless it is prevented. Also, the label
can indicate work procedures that are not safe.
IMPORTANT:
Only drive the machine at road speed when you are on a highway. You must not select road speed on grass
areas or rough roads and gravel tracks.
Some illustrations in this manual can show shields, guards or plates removed for clearness. This equipment must
not be operated without these devices correctly fastened in position.
By following all instructions in this manual, you increase the life of your machine and keep its maximum
performance. Adjustments and maintenance must always be done by an approved technician.
If additional information or service is needed. Contact your Authorized Ransomes Jacobsen Dealer, who knows
the latest methods to service this equipment and can give that service.
WARNING
The Interlock System on this mower prevents the starting of the mower unless a.) The parking brake is
Engaged. b.) The mow switch is in the OFF position, c.) The traction pedal is in the Neutral position. d) The
operator is in the seat. The system stops the engine when the operator leaves the seat a.) without the parking
brake engaged or b.) the mow switch is not in the OFF position. NEVER operate the mower unless the
Interlock System is working.
WARNING
1. Before leaving the operator’s position for any reason:
a. Return traction pedal to the Neutral position.
b. Disengage all drives.
c. Lower all implements to the ground.
d. Engage parking brake.
e. Stop the engine and remove the ignition key.
2. Keep your hands, feet, and clothing away from moving parts. Wait for all movement to stop before you
clean, adjust, or service the machine.
3. Keep the area of operation clear of all persons and animals.
4. Never carry any passengers.
5. Never operate the equipment without a correctly fastened grass deflector in position.

en-14
3 SAFETY
WARNING
California Proposition 65
Engine Exhaust, Some Of Its Constituents, And Some Vehicle Components Contain Or Release Chemicals
Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.
WARNING
To Prevent Injury From The Hot Oil At High Pressure, Do Not Use Your Hands To Check For Oil Leaks. Make
Sure That You Use Paper Or Cardboard.
Release Of Hydraulic Fluid At High Pressure Has Enough Force To Enter Through The Skin. If The Fluid Enters
Through The Skin, The Fluid Must Be Surgically Removed Within Hours By A Specialist Doctor Or Gangrene
May Result.
WARNING
When The Machine Is Driven Off-Road, A Seat Belt Must Be Worn Only When A Rops Frame Is In Position.
This Warning Is Because A Seat Belt Must Be Worn With A Rops To Follow The Machinery Directive,
2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover. (ANSI B71.4-2012 section 20.7)
Ransomes Jacobsen Limited Recommends That The Owner/User Of The Machine Completes A Local Risk
Assessment Of The Machine To Find Any Conditions That Do Not Follow This Rule. E.g. When You Drive The
Machine Next To Water Or On The Highway.
WARNING
Explosive Gases Are Released By Batteries. The Battery Contains Corrosive Acid And Supply An Electrical
Current That Is High Enough To Cause Burn Injuries To The Body.
WARNING
You Must Not Use This Machine To Tow Other Vehicles.
WARNING
Ear Protection Must Be Worn When You Operate Machines With
An Operator Ear Noise Level Of More Than 85 db(A) Leq.

en-15
SAFETY 3
WARNING
Vibration Exposure Limits
Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the
Daily Exposure Time (Trigger Time). E.g. A product with 5m/s² vibration can be used up to 2 hours/day to
reach the EAV and up to 8 hours/day to reach the ELV.
Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²
Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no action need be
taken
Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²
If several tools are use the exposure values must be combined:
Total exposure is then the combined value of the activities
WARNING
Never Mow If There Is A Risk Of Lightning Or You Hear Thunder. If You Are In The Middle Of Mowing,
Stop In A Safe Place, Turn Off The Engine And Go Inside a Building.
CAUTION
When You Do Any Welding On The Machine, The Battery, Controller And Display Must Be Disconnected
Before You Start. You Must Not Open The Controller. If The Controller Is Opened, This Can Cancel All Of The
Warranties And Can Cause The Failure Of The Machine.
CAUTION
Personal Protective Equipment (PPE), For Example Safety Glasses, Leather Work Shoes Or Boots, A Hard
Hat, Leather Work Gloves And Ear Protection Must Be Used After The Owner/User Completes A Local Risk
Assessment Of The Mower, To Prevent Injury.
Training In All Manual Operations Must Be Given By An Approved Person Before The Machine Is Used The
First Time.

en-16
3 SAFETY
NOTES

en-17
SPECIFICATIONS 4
4.1 ENGINE SPECIFICATION ______________________________________________
4.2 DIMENSIONS & WEIGHTS ________________________________________________
Type: Honda 2.95kW (4HP)/ 2700 RPM, single cylinder, air cooled 4 stroke OHV petrol
engine 25° inclined cylinder, horizontal shaft.
Model: GX160 K1-QX4
Maximum Speed: 2700 ± 50 RPM (No load).
Idle Speed: 1400 + 200 -150 RPM
Oil Sump Capacity: 0.6 litres (1 Imp Pints) (0.63 US qts)
Fuel: Lead free petrol
Overall height A 102cm (40in)
Overall length B 134cm (53in)
Overall width C 87cm (34in)
Width of cut D 71cm (28in)
Gross Dry Weight (incl.grass box) 153kg (336Ib)
Fuel Tank Capacity 3.6 litres 7 Imperial Pints 4.22 US Quarts
Fuel Grade 87 Octane Lead Free
Weight of 3.6 litres (0.95 US Gal) of Petrol 3kg (6.75lb)
A
B
C
D

en-18
4 SPECIFICATIONS
4.3 MACHINE SPECIFICATION_____________________________________________
Frame construction: Pressed Steel welded fabrication.
Transmission: By heavy roller chains.
Clutches: Transmission clutch.
Separate cylinder clutch.
Separate landroll clutch.
Front roll: One piece steel roll running on ball bearings.
Landroll: Two piece smooth cast iron with bevel gear differential.
Cutting cylinder: All welded 5 knife cylinder running on ball bearings.
Drive Train:
Traction Heavy Roller Chain and Cylinder Clutch
Cutting Unit Drive:
Separate Cylinder Clutch and Landroll - Separate Cylinder Clutch
Brakes:
Service NONE
Parking/Landroll Cable operated
Handles: Tubular steel adjustable at bottom.
Grass box: Fibreglass.
Ground pressure 0.45 kg./ cm2 (6.6lb./in2)

en-19
SPECIFICATIONS 4
4.4 VIBRATION LEVEL ___________________________________________________
The machine was tested for hand/arm vibration levels. The operator was in the normal position to drive the
vehicle, with two hands on the steering mechanism. The engine was in operation and the cutting device was in
rotation, while the machine was not moving.
The Machinery Safety Directive 2006/42/EC
By compliance to:
The Lawnmower Standard BS EN ISO 5395
Referenced to Hand/Arm: BS EN ISO20643:2008
Information Supplied for Physical Agents Directive 2002/44/EC
By reference to:
Hand/Arm Standards: BS EN ISO 5349-1 (2001)
BS EN ISO 5349-2 (2002)
The machine was tested for Whole Body vibration levels. The operator was in the normal position to drive the
vehicle, with two hands on the steering mechanism. The cutting device was in rotation with the machine driven in
a straight line at 6 Km/hr on a level and cut lawn.
The Machinery Safety Directive 2006/42/EC
By compliance to:
Whole Body EN1032:2003
Information Supplied for Physical Agents Directive 2002/44/EC
By reference to:
Whole Body Standards BS EN ISO 2631-1 (1997)
Ransomes Matador 71
Series EH4
Hand / Arm Acceleration
Level
Max. LH or RH
Accelerations m/s²
Mean Value of X, Y, Z Aeq
0.00 ± 0.00
Ransomes Matador 71
Series EH4
Whole Body Acceleration
Level
Max. Seat
Accelerations m/s²
Mean Value of X, Y, Z Aeq
0.00 ± 0.00
Ransomes Matador 71
Series EH4
Whole Body Acceleration
Level
Max. LH or RH Foot
Accelerations m/s²
Mean Value of X, Y, Z Aeq
0.00 ± 0.00

en-20
4 SPECIFICATIONS
4.5 NOISE LEVEL________________________________________________________
When the machine was tested for sound pressure (Operator Ear).
The Machinery Safety Directive 2006/42/EC
And
Exposure Of Workers To The Risks Arising From Physical Agents (Noise) Directive 2003/10/EC
By compliance to:
The Lawnmower Standard BS EN ISO 5395:2013
And
Sound Pressure Standard EN ISO 3746: 2010
Measured Sound Pressure 87 dB(A) ± 0.86 LWA
When the machine was tested for sound power (Noise in the Environment).
The Machinery Safety Directive 2006/42/EC
And
Noise Emission In The Environment By Equipment For Use Outdoors
Directive 2000/14/EC
By compliance to:
Sound Power Standard EN ISO 3744:2010
Measured Sound Power 95 dB(A) ± 0.86 LWA
4.6 SLOPES ____________________________________________________________
DO NOT USE ON SLOPES GREATER THAN 18°. This slope was calculated using static stability measurements
according to the requirements of BS EN ISO 5395