Rantopad MXX User manual

Backlight Function Instructions
Rantopad MXX RGB Mechanical Gaming Keyboard has made it possible for users to set and
combine lighting effects more conveniently. The Rantopad MXX RGB Mechanical Gaming Keyboard
backlight and key light can be adjusted separately as well as be activated simultaneously.
Backlight : Activation of all keys without operation, e.g. wave, breath etc.
Key Light: Only shown when any key is pressed, e.g. lights up, ripple. Key light will be on while backlight is on
when any key is pressed.
Without a driver the Rantopad MXX RGB will have 136 kinds of lighting effects by different
combinations of the preset, 9 kinds of RGB backlight modes (including off), 9 kinds of single color
backlight modes (including off), and 8 kinds of key light modes (including off). In single color
backlight mode, 729 colors are available to be adjusted. Brightness and speed of backlight and key
light can be adjusted separately.
With the driver installed each key can be set to 16.8 million colors on both backlight and key light
modes. EQ mode is also available once installed where the keyboard backlight can shine like an
equalizer, together with the rhythm of the music or movie being played. With the driver the
following driver-free light will be inactive and can only be set with the driver. You can save a
manifest file to the memory of the MXX RGB so that the functions set in the driver can be activated
driver-free the next time the MXX is activated. (Note: Only light settings and customized key
settings can be saved; micro saving is not available and EQ mode is only available with the driver is
activated.

Driver-free light effect operation manual
Press and hold FN, all keys with FN functions will light up in white.
FN+PRINT SCREEN, closes all backlight or opens all backlight and sets back to previous mode, speed
and brightness.
Key light:
FN+F12 switches light mode for key lights
FN+PAGE UP Adjusts the lighting speed of the key light. With 5 levels in total, each press will add
one level and will reset to minimum when activated again after the maximum setting. Factory
setting is set to maximum level.
FN+HOME/END Adjusts key light brightness. Press and hold to increase or decrease brightness with
21 levels in total (including off). Factory setting is set to maximum with minimum level being no
light/off
Light effect modes for key lights
No.
Name
Description
1
Changover
Press any key, then its color will change to a random color and
change to the backlight color gradually when you release (if
backlight is black, the light will turn off gradually).
2
Grid
Press any key, then the key pressed and the surrounding keys will
turn off. When you release, they will change to their backlight colors
gradually.
3
Ripple
Press any key, a random color will turn on and spread around from
the pressed key.
4
Expansion
Press any key, a random color will be on and spread in same row.
5
Tri-Expansion
Press any key, a random color will be on and spread out in the 3
surrounding rows.
6
Contraction
Press any key, a random color will be on and shrink from outer keys
to the center in the same row.
7
Tri-Contraction
Press any key, a random color will be on and shrink from outer to
center in the 3 rows around.
8
Off
Turn off key light.

Backlight:
FN+F10 choose an RGB backlight/single color backlight as backlight
FN+F11 switch light effect mode of backlight
FN+PAUSE stop/start dynamic light effect of backlight (to set current backlight color)
FN+PAGE DN Adjusts the lighting speed of the backlight. With 5 levels in total, each press will add
one level and will reset to minimum when activated again after the maximum setting. Factory
setting is set to maximum level.
FN+INSERT/DELETE, adjust backlight brightness. Press and hold will increase or decrease brightness.
There are 21 levels in total (including off). Factory setting is set to maximum with minimum level
being off.
Light effect mode details of RGB backlight
No.
Name
Description
1
RGB H
Wave
RGB color wave from left to right
2
RGB V
Wave
RGB color wave from top to bottom
3
RGB
Breath
Random RGB color breath
4
Spectrum
Random RGB color turn on and cycle like spectrum
5
RGB
Starlight
Random RGB color, random time and random effect turn on
6
RGB Scan
Random RGB color scan from left to right, then from right to left and
cycle
7
Bubble
Random RGB color spread out from two points
8
Mixture
Two random colors moves from two sides to the other and two colors
will fade and mix when met. After 3-4 routines, colors vanish from
middle to side and cycle like this.
9
off
Turn off RGB backlight

Light Effect Mode details for Single Color RGB
No.
Name
Description
1
Single Color
H Wave
Single color wave from left to right
2
Single Color
V Wave
Single color wave from top to bottom
3
Single Color
Breath
Single color breath
4
Single Color
On
Single color on
5
Starlight
Random light time and random single starlight effect on
6
Scan
Single color scan from left to right, then from right to left and cycle
7
Fireworks
3 single color light circles spread like fireworks
8
Explosion
A single color horizontal laser and a vertical one, explode when met
9
off
Turn off single color backlight
Single color backlight color setting method
In single color backlight, press FN+↑to enter single color backlight setting, keyboard light off and
all instruction lights（C, S,G) will shine continually.
Press and hold FN, ↑will be white, ←will be red, ↓will be green and →will be blue. Only these
four keys are the only ones able to function in single color backlight. Other keys will be able to
function when exiting single color backlight setting mode.
Press FN+←to adjust red brightness of backlight “R”. 9 levels in total (including no light), each
press will add one level and minimum level will be activated after maximum level.
Press FN+↓to adjust green brightness of backlight “G”. 9 levels in total (including no light), each
press will add one level and minimum level will be activated after maximum level.
Press FN+→to adjust blue brightness of backlight “B”. 9 levels in total (including no light), each
press will add one level and minimum level will be activated after maximum level.
While adjusting brightness of R, G, B, (the three original colors), the color shown is the combined
color of the three original color brightness. E.g. the color will be white when three colors are
adjusted to maximum level. When finished with the adjustment, press FN+↑to exit single color
backlight setting mode and all instruction lights (R, G, B) will turn back to normal.