Vortexgear POK3R User manual
!
http://amazon.com/Vortexgear or https://vortexgear.us
https://amazon.ca/Vortexgear or https://vortexgear.ca
POK3R User manual
The Vortexgear POK3R is the perfect solution for limited space in situations. It's
integrating 3 kind of layout. Also features 3 layers customization options individually
programmable key codes and LEDs, all easily set through what you want.
Main Features:
1. ANSI or ISO layout with 60% size
2. Cherry MX inside
3. Arbitrary programming key code and LED colors
4. ABS double shot Keycaps
5. 3 layers customization
6. Built-up 3 kind of layout (Qwerty, Dvorak, Colemak)
7. Metal bezel
Package Content:
1. Keyboard x 1
2. USB Cable x 1
!
http://amazon.com/Vortexgear or https://vortexgear.us
https://amazon.ca/Vortexgear or https://vortexgear.ca
Keycode Programming Instructions*1:
Step 1. Choose a layer (Fn+<,>or ?key) you want to edit the keycodes.
Step 2. Press Fn + Right CTRL to enter the programming mode (Spacebar right LED steadily lit)
Step 3. Select a desire key you want to program (Spacebar right LED flashing)
Step 4. Key in the programming contents and then press Pn(Spacebar right LED steadily lit again) Step
5. Repeat step 2 and step 3 to program other keys.
Step 6. Press Fn + Right CTRL to exit programming mode (Spacebar right LED off)
More:
· Support Fn layer programming, you can select the Fn combination key (e.g., Fn + A) to program it
· Support time delay, press 15ms key (Fn + T) each time to delay 15ms, press 0.1s key (Fn + G) each time
to delay 0.1s, press 0.5s key (Fn + B) each time to delay 0.5s. Consecutive delay will add up but will only
be counted as 1 key stroke.
· Every key can program up to 32 key strokes.
· If there is no key pressed for 15 sec in programming mode, it will back to normal mode.
Note: *1 Default layer, R_ctrl, M,<,> and ?keys are fixed can’t be
programmed.
Restore to factory
default:
Current layer: Press
and hold Fn + R All
layers:
Press and hold both Alt keys, it will clean all the layers’ program key codes.
Remark:
1. When you reset the current layer or all layers, the spacebar left LED will flash at the after 5 seconds
then it will return to default.
2. If you had changed the Fn position and forgot where it was. You still can press the original position of
Fn + R to restore it.
!
http://amazon.com/Vortexgear or https://vortexgear.us
https://amazon.ca/Vortexgear or https://vortexgear.ca
DIP Switch function descriptions:
SW 1
SW 2
Layout
Remark
ON
ON
=
Colemak
Default = OFF
ON
OFF
=
Dvorak
OFF
ON
=
Qwerty
OFF
OFF
=
Qwerty
ON
OFF
Remark
SW 3
CapsLock = Fn
CapsLock = CapsLock
Default = OFF
SW 4
Change
Fn & Pn at any position
Fn & Pn at original
position
R_CTRL Shall not be
changed to Fn or Pn
Others:
1. Fn + Shift + ESC = ~
2. L_Win + R_Alt + Spacebar:
The bottom right corner as arrow keys.
Table of contents
Other Vortexgear Keyboard manuals
