TO FRIENDS AND CUSTOMERS: As the owners of Real Avid, authenticity
isn’t just a strategy here. It’s a guiding philosophy. It arises out of
our faith and personal relationships with Jesus Christ. We know
that our creativity and success ultimately comes from Him. He cares
about each of us and about our customers. We’re not perfect, but we
are committed to following Him in our personal and business lives.
We look forward to growing our relationship with you and continuing
to earn our place.
©2023 New Revo Brand Group, LLC.
5480 Nathan Lane North, Suite 120
Minneapolis, MN 55442 USA
RealAvid.com • 800-286-0567
WARRANTY
LIMITED – 3 YEAR WARRANTY: Master Gun Workstation is guaranteed
free of defects in materials and workmanship for three years
from date of original purchase. Real Avid will replace or repair
any product that proves defective upon our inspection. Use of
the Master Gun Workstation for anything other than its intended
purpose is considered misuse and voids this warranty. For
warranty service, contact us at RealAvid.com. This warranty
excludes damage resulting from deliberate or accidental misuse.
Warranty does not cover rust, stains or corrosion, or normal wear
and tear. Repair or replacement is the exclusive remedy under
this warranty. Real Avid, its partners and afliates are not liable
for incidental or consequential damage resulting from use.
Some states do not allow exclusion or limitation of incidental or
consequential damages; therefore, the above exclusions may not
apply to you. This warranty gives you specic legal rights, and
you may have other rights, which vary from state to state.
CARE & MAINTENANCE: You already take good care of your guns - you should
treat your tools the same way. The high-quality coatings on the Master
Gun Workstation™provide enhanced corrosion resistance, but that does
not mean that it is corrosion proof. Perform general maintenance by wiping
up corrosive solvents and occasionally inspect for scratches or exposed
metal.Applying a very minimal coating of lightweight oil onto metal
surfaces after use will keep them looking good for the life of the product.
WARNING: If you suspect that your Master Gun Workstation has become
damaged, do not continue to use the product. Continuing to use damaged
equipment may increase the potential for slipping and potentially
damaging gun components which could lead to personal injury.
WARNING: To maximize the life of the foam pads and Gun Gripper™
technology, remove rearm after use and do not use Workstation for long-
term rearm storage.
THE MASTER GUN WORKSTATION IS INTENDED FOR
CLEANING, MODIFYING AND MOUNTING OPTICS. DO NOT
SHOOT A FIREARM WHILE MOUNTED IN WORKSTATION.
HOW TO USE YOUR MASTER GUN
WORKSTATION SAFELY AND EFFECTIVELY
SETUP AND USE:
1. Choose a suitable location for your Workstation, preferably on
a level, stable table or workbench.
2. Adjust the feet height of the Workstation to level it and correct
for any uneven surfaces.
3. To change the conguration of the Workstation, lay the Workstation
on its side and pinch the snaps together that are located below
the tower. Remove the Trigger Clamp, rotate 180° and reinsert.
MOUNTING A FIREARM INTO
THE WORKSTATION:
1. To mount a rearm into the
Workstation, start by pulling
the Trigger Clamp release
lever to open the clamp pads.
2. Squeeze the brake release
button on the Quick-Adjust
Shuttle and move the Shuttle
to an estimated location for
the length of the rearm
you want to place into the
Workstation.
3. Release the brake to secure
the Shuttle in place.
4. Adjust the height of the Gun-
Yoke by squeezing the height
adjust button.
5. Place your rearm into the Master Gun Workstation in your
desired orientation.
6. Squeeze the Trigger Clamp lever to apply pressure onto your
rearm.
7. Fine-tune the location of the Shuttle and the height of the Yoke.
Then press down on your rearm to rmly secure it into the Gun
Gripper of the Yoke.
LEVELING KNOB FOR OPTIC MOUNTING:
1. To level your rearm for scope mounting or adjusting, securely
install your rearm into the Workstation.
2. Next, unlock the Leveling Knob by pulling out on the knob and
rotating it from the 6 o’clock position to the 12 o’clock position.
Once the Leveling Knob is in the 12 o’clock position you can
now rotate the knob 90° right or left for ne adjustments.
3. Using the Real Avid Level-Right®Pro, you can now mount and
level your optic.
MOUNT SMART-ASSIST™ACCESSORIES:
1. Slide the Smart-Dock accessory mount to the desired position.
2. Insert Smart-Assist components (sold separately).
1
2
HEIGHT-ADJUSTABLE, NON-
SLIP FEET ARE CAPABLE
OF BEING CLAMPED TO
A BENCH OR BOLTED
DOWN FOR A LONG-TERM
SOLUTION.
UP TO 1"
WHEN INSTALLING OPTICS,
THE ACCU-LEVEL™
KNOB LOCATED ON THE
TRIGGER CLAMP OFFERS
6 DEGREES OF TILTING
MICRO-ADJUSTMENTS FOR
LEVELING FIREARMS.
+/-3°
TRIGGER CLAMP QUICKLY
ENGAGES AND DISENGAGES
FORM-FITTING FOAM PADS
WITH EASE, TO SECURE
YOUR FIREARM FOR THE
UTMOST PROTECTION.
