Recoil SWS10 User manual

SWS10/SWS12
RECOIL 10" /12" Shallow Active Subwoofer
User Manual
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12

Owner's Manual
Installation Wiring Kits
Remote Control
Bracket
Screws
Brackets Screws
Description
Woofer size:
Woofer Diaphragm
Power Rating (RMS/PEAK)
Crossover Slope
Crossover Frequency:
Punch Bass
Frequency Response
Input Sensitivity
Fuse Rate
Dimensions (HxWxD)
10"
Injection
200W/ 600W@2Ohm
12dB/Oct
30Hz-150Hz
Variable 0-9dB/50Hz
20Hz-150Hz
150mv @ MAX Gain
20A X 1
(12+21) X 38 X 52cm
(4.7+8.2) X 14.9 X 20.4in
12"
Injection
200W/ 600W@2Ohm
12dB/Oct
30Hz-150Hz
Variable 0-9dB/50Hz
20Hz-150Hz
150mv @ MAX Gain
20A X 1
(14+23) X 39 X 53cm
(5.5+9.0) X 15.3 X 20.8in
1 piece
1 Set
1 piece
4 pieces
8 pieces
8 pieces
10/12" Subwoofer Box with Built-in Amplifier
Thank you for your purchase and welcome to RCEOIL ! In order to enjoy the
better service from us, please keep your original invoice well and complete the
warranty card. You'd better post the copy of the warranty card back to the
appointed service agent of RCEOIL, So that you may get more technical
support.
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12
SPECIFICATIONS
ACCESSORY LIST
Do not operate any function that takes your attention away from safely driving
your vehicle. Any function that requires your prolonged attention should only be
performed after coming to a complete stop. Always stop the vehicle in a safe
location before performing these functions. Failure to do so may result in an
accident.
Keep the volume at a level where you can still hear outside noises while driving.
Excessive volume levels that obscure sounds such as emergency vehicle sirens or
road waming signals (train crossings etc.) can be dangerous and may result in
an accident. Listening at loud volume levels in a car may also cause hearing
damage.
WARNING

Do not disassemble or alter. Doing so may result in an accident, fire or electric
shock.
Use this product for mobile 12V applications.
Use the correct ampere rating when replacing fuses. Failure to do so may result
in fire or electric shock.
Do not block vents or radiator panels. Doing so may cause heat to build up
inside and may result in fire.
Make the correct connections. Failure to make the proper connections may
result in fire or product damage.
Use only in vehicles with a 12 volt negative ground. Failure to do so may result
in fire, etc. (Check with your dealer if you are not sure.)
Before wiring, disconnect the cable from the negative battery terminal.
Do not allow cables to become entangled in surrounding objects. Arrange
wiring and cables in compliance with the manual to prevent obstructions when
driving. Cables or wiring that obstruct or hang up on places such as the steer-
ing wheel.
Do not splice into electrical cables. Never cut away cable insulation to supply
power to other equipment. Doing so will exceed the curent carrying capacity
of the wire and result in fire or electric shock,
Do not damage pipe or wiring when drilling holes. When drilling holes in the
chassis for installation, take precautions so as not to contact, damage or
obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precau-
tions may result ín fire.
Do not use bolts or nuts in the brake or steering systems to make ground con-
nections.
Keep small objects such as bolts or screws out of the reach of chlldren. Swal-
lowing them may result in serious injury. If swallowed, consult a physician imme-
diately.
WARNING
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12

Halt use immediately if a problem appears. Failure to do so may cause personal
injury or damage to the product. Return it to your authorized dealer or the
nearest Service Center for repairing,
Have the wiring and installation done by experts.The wiring and installation of this
unit requires special technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to have the work done.
Use specified accessory parts and install them securely. Be sure to use only the
specifed accessory parts. Use of other than designated parts may damage this
unit internally or may not securely install the unit in place.
Arrange the wiring so it Is not crlmped or pInched by a sharp metal edge. Route
the cables and wiring passes (like the seat rails) or sharp or pointed edges. This
will prevent crimping and damage to the wiring. If wiring passes through a hole
in metal, use a rubber grommet to prevent the wire's insulation from being cut by
the metal edge of the hole.
Do not install in locations with high moisture or dust. Avoid installing the unit in
locations with high incidence of moisture or dust, Moisture or dust that pene-
trates into this unit may result in product failure.
CAUTION
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12

1.Attach the inclucled mounting plates with the supplied screws.
2.Once the mounting plates are attached, position the SWS10/SWS12 in the
desired location within the vehicie. Before securing, check to make sure all the
screw locations can affix to a structurally solid surface, while avoiding vehicle
wiring, components, etc.
MOUNTING
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12

WIRING DIAGRAM
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12
Power connector
+12V Power
+12V Remote
(-)12V Ground
Remote Level
Controller Jack
LED indicator
Blue:Power ON
Red: Protection/Fault
Speaker Input connector (High Level)
Boost (0db-9db)
Phase (00-1800)
Low Pass Filter
30Hz-150Hz
LEVEL
RCA Input (Low level)
FUSE (20A)

1. Low-pass Filter
A built-in 12dB/octave flter with a crossover point variable from 30Hz to 150Hz.
This setting allows you to adjust your subwoofer system's crossover frequency. The
most common setting is between 70Hz and 90Hz depending on the bass output
of satellite speakers.
2. Remote Level Control
In systems where separate subwoofer level control is unavailable, the included
remote bass control may be used to adjust the bass level remotely. If set to
maximum as recommended during initial setup, it will function as an attenuator.
6. Phase Select Switch
With this switch at 00, the SWS10/SWS12 output will be in phase with full-range
speakers in the system. At 1800, it will be out of phase. It may be advantageous
to try both positions, depending on the particular vehicle or subwoofer location.
10. LEVEL
Using a dynamic music CD as a source, and with GAIN set to MIN (minimum),
increase the headunit volume until the output becomes noticeably distorted.
Then reduce the headunit volume to just below the point of distortion onset.
Adjust the GAIN as necessary to achieve maximum system volume at minimum
amplifier gain while avoiding output clipping. IMPORTANT NOTES: For initial GAIN
adjustment with Remote Bass Control, if used, set to maximum.
7. Power-Protect LED
lluminates Blue when the unit is turned on. lluminates Red if a short circuit or other
fault is detected. The amplifier will automatically shut down if this occurs.
9. Power Connections
Use the included installation wiring kits for the amplifier's power connections:
+12V Power, -12V Ground, & +12V Remote.
8. Fuse
Use 20 Amp fuse. Replace ONLY with the same value fuse.
4. RCA Inputs
Connect to Left and Right RCA inputs.
5. Speaker Input Connection
Connect to Left and Right Speaker (+/-) high level inputs.
3. BOOST: 0db - 9db
WIRING DIAGRAM
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12

WIRING DIAGRAM
Power Connector
REM
BATT
+12V
FUSE(20A)
Bass Remote Level Control
Boost 0db-9db
Phase Select Switch 00-1800
Low Pass Filter 30Hz -150Hz
RCA Input(Low level)
Speaker Input connector( High Level )
LED indicator
Blue: Power ON
Red: Protection/Fault
SHALLOW ACTIVE SUBWOOFER MANUAL SWS10/SWS12