Recordex 500SCT User manual

Installation Guide
ENGLISH
Lightweight Suspended Ceiling Projector Mount Kit
KIT INCLUDES: 500SCT, 500UCM
500PLB (optional)
Set Screw
A7
A6
A6
A6
A6

2
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Copyright
Copyright ©2008 Recordex USA, Inc. All rights reserved. No part of this user’s guide may be reproduced in any
form without the express written permission of Recordex USA, Inc. Note: User’s are permitted to print copies of
this guide for personal use.
Trademarks
Recordex and all Recordex product name are the registered trademarks of Recordex USA, Inc. All other trademarks
acknowledged.
Disclaimer
The information in this document is subject to change without notice.
RECORDEX USA, INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL., EITHER EXPRESS OR
LIMITED, EXCEPT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO MARKET-
ABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR AGAINST INFRINGEMENT OF ANY PAT-
ENT. RECORDEX USA, INC. SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.
Information & Support
Before calling for support please read the user’s guide. Should service be necessary please contact the Recordex Resell-
er who sold you the Infinix SCM, or contact us using the contact information below.
Recordex USA, Inc.
PO Box 848
105 North Anderson Drive
Swainsboro, GA 30401
1-478-237-5501

3
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Warranty
Limited 10-year Warranty on Infinix SCM™ Lightweight Suspended Ceiling Projector Mount Kit
WRecordex warrants to the original purchaser only that the Mounting Kit will be free from defects in material
and workmanship under normal use for a period of ten (10) years from the date of original purchase. However, Recordex does
not warrant against failures related to improper installation or improper use. Recordex's warranty shall not apply: (i) to any auto-
printer subjected to accident, misuse, neglect, alteration, acts of God, improper handling, improper transport, improper storage,
improper use or application, improper installation, improper testing or unauthorized repair; or (ii) to cosmetic problems or de-
fects that result from normal wear and tear under ordinary use, and do not affect the performance or use of the product. If the
Mounting Kit develops a covered defect within the first year, Recordex will, at its option, either repair or replace the Mounting Kit
at no charge, provided that the original Mounting Kit is returned during the warranty period.
Ten (10) years from the date of the original purchase.
You are responsible for shipping the defective Mounting Kit to our Service Depot. Recordex
will pay for return shipment of repaired Mounting Kit or replacement Mounting Kit under warranty. Return shipment will be by
ground service to the 48 contiguous US states. You are responsible for shipping to Alaska, Hawaii and any address outside of
the United States. If the Mounting Kit is repaired out of warranty then you are responsible for shipping both ways.
To obtain warranty service please contact Recordex's Customer Service Center at
1-478-237-5501 or contact your authorized Recordex Dealer for assistance in filing a warranty claim. You will receive instruc-
tions on how to properly return your product for authorized warranty repair. In order to receive warranty service you must be able
to provide an original receipt for the purchase of your Ceiling Mount (or other proof that you are the original owner).
THE ABOVE STATED WARRANTY IS EXCLUSIVE AND REPLACES ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. RECORDEX WILL NOT BE HELD LIABLE FOR ANY
OTHER DAMAGES OR LOSS INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES AND LOSS OF PROFITS OR REVENUES
FROM WHATEVER CAUSE, INCLUDING BREACH OF WARRANTY OR NEGLIGENCE.
The following type conventions, terms, symbols, and abbreviations are used to make it easier for you to navigate the infor-
mation contained in this Users’s Guide.
Symbols
CAUTION: Indicates a caution warning regarding operation of the system that may lead to personal injury or dam-
age to the autoprinter. Be sure to take careful note of any instruction flagged with a caution symbol.

4
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Customer Support
Your Infinix SCM Mounting Kit was subjected to rigorous quality control testing and inspection, however, if you encounter a
problem during installation please contact our support department so we quickly resolve the issue. We strive to build the
best product possible and we desire that every customer feel confident recommending Recordex products. If you are not
fully satisfied please call our Customer Service Center today and we will do our best to make things right.
Customer Service Center
Recordex USA, Inc.
PO BOX 848
105 North Anderson Drive
Swainsboro, GA 30401
P. 1-478-237-5501
F. 1-478-237-5504
Safety Precautions
Please read through these important safety precautions and recommendations before setting up your Infinix SCM.
This installation guide includes important information and a thorough understanding of the guide is necessary to
ensure proper installation. Failure to read, fully understand, and follow the instructions found in this guide can re-
sult in serious personal injury, damage to the product and related equipment, and may render your product war-
ranty void. The installer of this product is responsible for making sure that the Mounting Kit is properly assembled
and installed.
This mount requires adequate structural support and the installer is responsible to make sure that the supporting
structure can support up to 5 times the weight of all equipment attached to the Mounting Kit. Proper reinforcement
of the structure may be required before installation. Inadequate structural support can result in serious personal
injury, and damage to equipment.
This Mounting Kit is rated to support up to 50 pounds. Exceeding the weight capacity can result in serious personal
injury or damage to equipment. The installer is responsible for making sure that the total combined weight of all
product attached to this Mounting Kit does NOT exceed 50 pounds.
!
!
!

5
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Unpacking Your Infinix SCM™
Take a moment to make verify the contents:
#
QTY
DESCRIPTION #
QTY
DESCRIPTION
A1 1 Ceiling Mounting Plate C1 1 Adjustable Ceiling Mount
A2 4 5 mm Wing Nuts C2 1 Universal Projector Sled
A3 4 1.6 mm x 7.6m (25 ft) Safety Wire C3 4 Adjustable Spider Mounting Arms
A4 4 Fastlok Wire Locks C4 4 Thumb Nuts
A5 4 Eye Lag Wood Screw (6.7 mm x 33 mm) C5 1 1/2” Set Screw
A6 4 #10 x 5/8” Screw (4.8 mm x 16 mm) C6 12 #10-24 x ½ Pan Head Screw w/Nylon washer
A7 1 1/4” Set Screw C7 4 Pan Head Screw
A8 1 Finishing Ring C8 4 Square Nut
C9 4 Pan Screw w/Locking washer and flat washer
B1 1 3” or 6” Extension Pipe C10 4 M3 Standoff with Screw & Washers
C11 4 M4 Standoff with Screw & Washers
C12 4 M5 Standoff with Screw & Washers
C13 4 M6 Standoff with Screw & Washers
A1 (1)
A2 (4)
A3 (4) A4 (4) A5 (4)
A6 (4) A7 (1) A8 (1)
B1 (1) C1 (1) C2 (1) C3 (4)
C4 (4) C5 (1) C6 (12) C7 (4) C8 (4) C9 (4) C10 (4) C11 (4) C12 (4) C13 (4)
Figure 1: Parts Listing
or

6
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Ceiling Mounting Plate–A1 (SKU:500SCT)
Extension Column – B1 (3” or 6”)(SKU:500006)
23.38 [594]
23.38 [594]
1.125 [28.6]
1.125 [28.6]
8.0 [203]
3.0 [76]
6.0 [152]
1.5 [38] 1.5 [38]

7
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Adjustable Ceiling Mount–C1 (SKU:500UCM)
Universal Projector Sled with Adjustable Spider Mounting Arms – C2 & C3 (SKU:500UCM)
5.43 [138]
4.77 [121]
2.87 [73]
2.36 [60]
3.89 [99]
5.43 [138]
2.72 [69]
2.68 [68]
2.36 [60]
2.36 [60]
5.43 [138]
5.43 [138]
5.47 [139]
5.47 [139]
1.38 [35]
2.13 [54]
5.47 [139]
5.47 [139]
5.47 [139] 3.94 [100]
3.50 [89]
4.72 [120]

8
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Optional Plenum Box(SKU:500PLB)
14.0 [356]
5.0 (127)
7.67 (195)

9
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Tools Required For Installation
ŸMarking Pen or Pencil
ŸHole Saw (2” diameter)
ŸPhilips Head Screw Driver (#2)
ŸRuler/Tape Measure
ŸAllen Wrench (included)
Preparing Ceiling for Installation
Select the appropriate ceiling grid cell for installation of mount. This will be based on the recommended installation instruc-
tions for your projector. Refer to projector installation instructions to determine distance from projector to target surface.
Identify the grid cell that meets your distance from target requirements then follow these steps:
1. Determine precise placement for the extension column and mark the center on the finished (down) side of the tile.
TIP: Make sure that the Infinix SCM will fit in the desired location (consider orientation and placement of Infinix SCM).
2. Remove the tile from the grid.
TIP: It may be helpful to remove adjacent tiles to improve access to the workspace above the ceiling.
TIP: If you remove extra tiles place a mark the ceiling grid supports where the mount will be installed.
3. Use hole saw to cut 2” diameter hold in tile.
4. Replace tile into ceiling grid.
TIP: Be sure to place the cut tile back into the proper ceiling grid cell.
5. Install the ceiling mounting plate (A1) on top of the ceiling tile
you just replaced. Be sure that the short end (8”) of
the mounting plate (A1) straddles the taller 1½”
primary ceiling grid rail to ensure adequate structural
support (See Figure 2)
6. Loosen the four wing nuts (A2) and by moving the mounting plate along
the ceiling rails and adjusting the position of the pipe coupling ensure
that the pipe coupling for the extension column is positioned directly
over the 2” hole cut from the tile.
7. Tighten the wing nuts.
8. OPTIONAL: The ceiling plate is designed to accept standard electrical gang boxes. If these are to be used then mark
the position of the gang box knockouts.
9. Identify the optimal location to secure the four safety wires (A3) using these guidelines:
- do not anchor wires directly above the support holes rather anchor wires approximately 10 to 15 degrees away
from the support holes, but not more than 20 degrees (See Figure 3).
10. Mark where the safety wire anchors should be installed.
11. Remove the Ceiling Mounting Plate and the ceiling tile.
12. OPTIONAL: Cut out gang box opening where marked in step 8 above.
Figure 2
Figure 3

10
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Safety Wire Installation
This mount requires adequate structural support and the installer is responsible to make sure that the supporting
structure can support up to 5 times the weight of all equipment attached to the Mounting Kit. Proper reinforcement
of the structure may be required before installation. Inadequate structural support can result in serious personal
injury, and damage to equipment.
This Mounting Kit is rated to support up to 50 pounds. Exceeding the weight capacity can result in serious personal
injury or damage to equipment. The installer is responsible for making sure that the total combined weight of all
product attached to this Mounting Kit does NOT exceed 50 pounds.
Failure to properly install safety wires may result in serious personal injury and damage to equipment. Installer is
responsible for inspecting the wood, concrete and steel structure to ensure that it is sound and capable of providing
adequate structural support.
Concrete anchors must be installed into solid concrete, hollow concrete block will not provide adequate structural
support. Concrete anchors should not be installed within 2½” of concrete edge.
!
!
!
!
If installing into wood follow these directions:
1. Drill a 0.113” (#33 bit) pilot hole into the four locations where
previously marked.
2. Twist the four wood eye lag screws (A5) into the pilot holes.
3. Use the loop end of the safety wire to easily secure the wire to
the eye lag. (See Fig 4)
4. Do not secure wires to tray. Proceed to next page.
If installing over steel trusses follow these directions:
5. Use the loop end of the safety wire to easily secure the wire to
the truss (See Fig 5) where previously marked.
6. Secure all four safety wires.
7. Do not secure wires to tray. Proceed to next page.
If installing into concrete follow these directions:
8. Select proper concrete anchors (capable of bearing a minimum
load of 250 pounds of tension).
9. Install concrete anchors according to the manufacturers recom-
mended installation method.
10. Install a concrete anchor at four locations where previously
marked.
11. Use the loop end of the safety wire to easily secure the wire to
the concrete anchor. (See Fig 6)
12. Do not secure wires to tray. Proceed to next page
Figure 4. Wood Structure
Figure 5. Steel Truss
Figure 6. Concrete Structure

11
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Ceiling Mounting Plate
Installation
1. Replace the ceiling tile, with the hole cut
for the extension column into in the ceiling
grid. Make sure you have the tile oriented
correctly.
2. Install ceiling mounting plate (A1) on ceil-
ing grid above the tile.
3. Position the plate (A1) on the grid, and
position the pipe coupling to make sure
that it lines up with the hole cut from the
tile.
4. Secure plate to ceiling grid using the #10
x 5/8” screws (A6).
5. Thread the safety wires (that should be
hanging from the anchors that were in-
stalled in the last section) through the fast-
lok wire locks, through holes in the end of
the ceiling mounting plate, and then back
through the fastlok wirelock (See Figure 7).
6. Tighten the wires so that the full weight of
the ceiling mounting plate is supported by
the safety wires. The ceiling grid should
not be supporting the weight of the mount-
ing plate. DO NOTE OVER TIGHTEN the
safety wires, doing so could cause dam-
age to the ceiling grid.
Extension Column Installation
1. Thread the extension column through the hole in the ceil-
ing tile and into the pipe coupling of the ceiling mount
plate.
2. Thread the pipe as far as desired and then secure the
pipe with the 1/4” set screw (A7).
NOTE: You will need to loosen the set screw to adjust
column height if adjustment is necessary.
3. Install the finishing ring around the extension column to
cover the edges of tile where the hole was cut.
Set Screw
A7
Figure 8. Extension Column
Set Screw
A7
A6
A6
A6
A6
Figure 7. Install Plate & Tighten Safety Wires

12
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
OPTIONAL: Plenum Box Installation
The plenum box is designed to help reduce fire hazard by containing heat and flame to the plenum box if an electrical
fire were to begin inside the plenum box. The plenum box (ITEM: 500PLB) is available from any Authorized Recordex
Reseller.
1. Place plenum box on over the area of the ceiling mount plate where the extension column attaches.
2. Line the plenum box up with the mounting holes on the side of the ceiling mounting plate.
3. Securely attach the plenum box using the included hardware (4 self-tapping pan head screws)
4. Remove knock-outs as needed to facilitate cabling and wiring to the plenum box.
Figure 9. Optional Plenum Box

13
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Projector Mount Installation
The projector mount will attach to the Ceiling Kit using the extension column.
1. Separate the top portion of the projector mount (C1) from the bottom
portion (C2, universal projector sled) by loosening the thumb nuts and
removing the sled.
2. Thread the Adjustable Ceiling Mount (C1) onto the extension column
(B1) at least ½ inch (see Figure 10).
3. Tighten the set screw (C5) to temporarily set the mount position. To
make a final yaw adjustment you will need to loosen the set screw,
adjust the mount, and then re-tighten the set screw.
4. Determine the proper standoffs to use with your projector. M3, M4,
M5 and M6 standoffs are provided with the mount and one of these
sizes should fit any standard projector.
5. Thread the appropriate standoff into the mounting holes on the bottom
of the projector.
6. Align the universal mounting arms (spider arms) so that they line up
with the projector’s mounting holes.
NOTE: If the projector only has three mounting holes then you can re-
move one of the spider arms or you can leave it attached to the mount
for possible future use. Position the unused arm out of the way and
tighten the thumb screw.
7. When the universal mounting arms (C3) are lined up with the standoffs
then use the screw and washer provided with the standoff to attach
the mounting arm’s adjustable mounting foot with to the standoff (see
Figure 11). Repeat for all three or four mounting points.
8. After the project is secured to the mounting arms securely tighten the
screws (C7) to ensure that the mounting arms will not move out of their
current position (Figure 12)
C6 Roll/Pitch
Adj. Screws
C5
Set Screw
B1
C1
C10-13
Standoffs
C3
Mounting Hole (bottom of projector)
C7 Screws
Figure 10. Thread Mount
Figure 11. Attach Sled to Projector
Bottom of Projector
Figure 12. Secure Mounting Arms

14
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
1. Attach the universal projector sled (C2) to the Ad-
justable Ceiling Mount (C1) and secure in place by
tightening the four thumb nuts (C4) (See Figure 13).
2. The Adjustable Ceiling Mount (C1) can be adjusted
for roll, pitch and yaw.
3. The yaw adjustment is made by loosening the set
screw and threading the mount (C1) clockwise or
counter clockwise on the extension column. Be sure
to re-tighten the set screw after making the final
yaw adjustment.
4. The pitch adjustment is made by loosening the four
adjustment screws (C6), two on the front and two on
the back, making the pitch adjustment, and then
tightening all four screws to set the position.
5. The roll adjustment is made by loosening the four
adjustment screws (C6), two on either side, making
the roll adjustment, and then tightening all four
screws to set the position.
Figure 13. Attach Projector & Sled to Ceiling Mount
B1
C1
C2
C10-13
C4
C6

15
©2008 Recordex USA, Inc. All rights reserved.
Version: 1.1
Installation Guide Recordex Infinix SCM
®
TM
Every Infinix SCM™ is rigorously tested before it is shipped to ensure trouble free operation. However, if you find you
need assistance or need to report a problem with your mount don’t hesitate to give us a call.
Contact Technical Support
Recordex Technical Support
PO BOX 848
Swainsboro, GA 30401
1-478-237-5501
1-478-237-5504
[email protected]
CHECKLIST
1. Make sure you’ve read this manual thoroughly before calling.
2. Write down the model number & serial number
of your duplicator.
Model#: _____________________
Date of Purchase: _____________________
Place of Purchase: _____________________
4. Call 478-237-5501 ask for technical support.