Extron electronics SMK 2 User manual

1
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
www.extron.com
SMK 2 • Installation Guide
Overview
ATTENTION:
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
This guide provides instructions for professional installers to mount and
install the TLP Pro 725M to a wall or glass surface using the SMK 2
mounting kit. The kit consists of:
A(1) SMK 2 plastic enclosure (see gure 1) with an adhesive patch on
the back.
BThe SMK 2 Alignment Guide, which should be downloaded from
www.extron.com.
C(1) Cover Overlay.
The kit also includes the following optional items:
• (1) LED Overlay (see figure 5, 5, on the next page).
• (4) M3 Screws (see figure 5, 6).
Cover
Overlay
SMK 2
A
lignment
Guide
y
Outer edge of
TLP Pro 725M
Bottom, inner
edge of SMK 2
(the side with the
adhesive patch)
Alignment Guide for the Extron
SMK 2
Page size: 8.5" x 11"
Print scale 1:1
Do not shrink.
1. Confirm the product to
be installed.
2. Double-check the print
settings, before printing.
Make sure the scale
settings are 1:1.
3. Decide where to mount
the SMK 2. Use this guide
to ensure there is enough
clearance at the sides
to mount the touchpanel.
4. Stick this guide to the
glass on the opposite
side from where the
SMK 2 is being mounted.
Use a level to make sure
the guide is horizontal.
5. Align the bottom edge of
the SMK 2 (on the side
with the adhesive patch)
with the red line on the
guide.
P/N 68-3236-01 Rev. A
S
MK
2
ick thi
ass on
the op
de from where the
MK 2 is being mounted.
se a level to make sure
e guide is horizontal.
ign the bottom edge of
e SMK 2 (on the side
th the adhesive patch)
th the red line on the
uide.
P/N 68-32
36-01 Rev. A
C
A
B
Figure 1. SMK 2 Kit
Before Starting
Remove one or more knockouts from the SMK 2 enclosure to run
cables to the back of the TLP Pro 725M. The SMK has four knockouts
(see gure 2, A), one in the middle of each side.
You may need to use a sharp knife to cut the plastic holding the
knockout in place.
Option 1: Mounting the SMK 2 to a Wall
with Fasteners
To mount the SMK 2 to a wall or furniture, drill holes through the four
dimples in the plastic (see gure 2, B) and attach to the mounting
surface.
The installer must use screws that are appropriate for the mounting
surface.
B
A
B
A
B
B
A
A
Figure 2. SMK 2 Knockouts and Mounting Holes
1
Outside Glass Surface
Inside Glass
Surface
2
Outeredge of
TLP Pro725M
Bottom, inner
edge of SMK 2
(the sidewith the
adhesive patch)
Alignment Guide for the Extron
SMK 2
Page size: 8.5" x 11"
Print scale 1:1
Do not shrink.
1. Confirm the product to
be installed.
2. Double-check the print
settings, before printing.
Make sure the scale
settings are 1:1.
3. Decide where to mount
the SMK 2. Use this guide
to ensure there is enough
clearance at the sides
to mount the touchpanel.
4. Stick this guide to the
glass on the opposite
side from where the
SMK 2 is being mounted.
Use a level to make sure
the guide is horizontal.
5. Align the bottom edge of
the SMK 2 (on the side
with the adhesive patch)
with the red line on the
guide.
P/N 68-3236-01 Rev.A
Outside Glass Surfac
e
e size: 8.5
"
x11
"
Print scale 1:1
Do not shr
ink.
firm t
he product t
o
nstalle
a
d.
ble
e-
e-c
e-c
-c
-c
ing
g
gs
s
s
s,
e s
s
su
u
u
ur
ing
g
g
s
s
gs
ide
e
e
e
w
SM
M
M
MK
K
K
ns
su
u
u
u
re
ra
an
n
n
nc
c
mou
u
u
un
n
nt
k t
th
h
h
h
hi
s
ss o
o
o
o
on
n
e fr
ro
o
o
o
om
K2
2
2
i
i
is
a
l
le
e
e
ev
gu
ui
i
id
d
de
n t
t
th
h
h
he
SM
M
M
MK
K
K
th
h
he
e
e
e
th
h
he
e
e
e
de.
.
P/N
check the print
,
r
a
w
K 2
e
ce
t
s
n
m
s
v
e
e
K
a
r
6
heck the print
b
e
ar
wh
2.
e t
ea
t
s g
th
m w
b
ve
e i
b
2
ad
re
68
eck the print
b
efore printing.
t
he scale
r
e 1:1.
here to mou
nt
t
.
Use this gu
gui
de
t
here is eno
nou
gh
a
t the side
des
h
e touch
hpanel
.
guide to
o t
he
h
e oppo
posite
w
here
e the
be
ing m
mounted.
l
to m
make sur
e
i
s hor
rizontal
.
bottom
m edge
of
(
on t
the side
d
hesi
ive patch
)
e
d line
e on th
e
8-323
36-
01 Rev.A
4
4
3
Figure 3. Place the Template
Option 2: Mounting the SMK 2 to
a Glass Surface
1. Clean both sides of the glass with a lint-free cloth and a 50:50
mixture of isopropyl alcohol and water.
2. Place the SMK 2 Alignment Guide on the inside glass surface
(see gure 3, 1), so that it does not get wet when you apply the
soap solution.
Use tape (2) to attach the alignment guide to the glass, and use
a level (3) to ensure it is at the correct angle.
3. Remove the plastic backing from the adhesive patch.
TIP: Wet your ngers to prevent them from sticking to the
adhesive patch.
4. Spray the adhesive patch and the outside glass surface with
soap solution (two drops of detergent in a quart of water) (4).
gure 1

2
© 2018 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
SMK 2 • Installation Guide (Continued)
5. Carefully align the bottom inner edge of the SMK 2 with the red line on the
alignment guide marked “Bottom, inner edge of SMK 2” (see gure 4, 4).
You can slide the adhesive patch quite easily while it is still wet.
6. Allow the adhesive to cure at least 24 hours before attaching the touchpanel.
7. Remove the paper alignment guide.
Mounting the Cover Overlay (Optional)
The cover overlay is not required for mounting the touchpanel, but can improve
the aesthetics of the SMK 2 when it is viewed through the window from inside
the conference room.
1. Spray the inside surface of the glass with the soap solution.
2. Remove the paper backing from the cover overlay (see figure 1, C, on the
previous page).
TIP: Wet your ngers to prevent them from sticking to the adhesive
patch.
3. Center the cover overlay behind the SMK 2 enclosure.
4. Use a credit card or similar at edge to remove any air bubbles and a cloth
to absorb excess liquid.
TOP
Mounting Plate
LED Overlay
TLP Pr
o 725M
TLP Pro 7
2
TL
6
5
10
Back View
8
8
7
9
Figure 5. Mounting the TLP Pro 725M
Mounting the TLP Pro 725M
NOTE: Make sure the adhesive securing the SMK 2
to the glass has dried. Extron recommends waiting at
least 24 hours before attaching the touchpanel.
1. Remove the paper backing, and attach the LED
overlay to the back of the TLP Pro 725M (see
gure 5, 5). This overlay covers the rear panel LEDs
so that they do not cause a distraction inside the
conference room.
2. Run an Ethernet cable to the SMK 2 and pass the
cable through the mounting plate.
3. Fasten the mounting plate to the SMK 2 using the
four M3 screws provided (6). Use the holes marked
EU on the mounting plate.
4. Attach the Ethernet cable to the LAN/PoE input on
the TLP Pro 725M rear panel (see the TLP Pro 725
and 1025 Series User Guide).
Pass the cable through the gap left by removing the
knockout (see Before Starting on the previous page).
5. The mounting plate has four hooks (7), one on
each corner. Position the TLP Pro 725M so that
these hooks t into the four slots on the rear panel
of the touchpanel (see the TLP Pro 725 Series and
TLP Pro 1025 Series User Guide).
6. Slide the TLP Pro 725M down slightly so that the
hooks are seated securely in the slots.
7. The tongue at the bottom of the mounting plate (8)
sits in the groove in the bottom of the touchpanel
(see inset, 9). Fasten the touchpanel to the
mounting plate by tightening the lock screw (¢).
Outeredge of
TLP Pro725M
Page size: 8.5" x 11"
Print scale 1:1
Do not shrink.
1. Confirm the product to
2. Double-check the print
settings, before printing.
Make sure the scale
3. Decide where to mount
the SMK 2. Use this guide
to ensure there is enough
clearance at the sides
to mount the touchpanel.
4. Stick this guide to the
glass on the opposite
side from where the
SMK 2 is being mounted.
Use a level to make sure
the guide is horizontal.
5. Align the bottom edge of
the SMK 2 (on the side
with the adhesive patch)
with the red line on the
P/N 68-3236-01 Rev.A
Outeredge of
TLP Pro725M
Page size: 8.5
"
x11
"
Print scale 1:1
Do not shrink.
1. Con
onfirm t
he product to
2. D
Double-ch
eck the print
settings, b
efore printing.
Make sure t
he scale
3. Decide
where to mount
the SMK 2. Use this guide
to ensure there is enough
clearance at the sides
to mount the touchpanel.
his guide to the
opposite
he
4
to m
4. Stick this g
glass on th
e opp
side from w
here the
SMK 2 is be
ing mounted.
Use a level
Use a level
Use a level
Use a level
Use a level
Use a level
Use a level
e a level
a leve
to make sur
to make sur
to make sur
to make sur
to make sur
to make sur
to make sur
to make sur
r
to make sur
o make sur
r
make sur
ur
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
the
the gu
the guide i
the guide i
the guide i
the guide i
s ho
s horizonta
s horizontal
s horizontal
al
.
5. Align the
bottom edg
edge
of
the SMK 2 (
on the
e side
with the ad
hesive
sive patch
)
with the re
d lin
line on th
e
P/N
P/N 68-3236-
01 Rev.A
Figure 4. Attach Adhesive Patch and
SMK 2 to the Glass
gure 5
68-3233-01 Rev. B
04 18