Redgum Super VHD 32000 User manual

RGVLS-0522 Rev 0
Australia's No.1 Selling Honda-Powered Log Splitters
LOGSPLITTERS
Super VHD
3200032000

HAZARD SIGNAL DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in serious injury or death.
WARNING indicates a potentially hazardous situation which, if not
avoided, will result in serious injury or death.
CAUTION indicates a potentially hazardous situation which, if not
avoided, could result in minor or moderate injury.
DANGER
WARNING
CAUTION
WARNING
Read and thoroughly understand all instructions contained in
this operation manual before operating this RedGum Splitter.
Serious injury or death can result if safety instructions are not
understood or followed. If you wish to discuss this log
splitter’s operational procedures after reading this manual,
please call our Customer Service on 1300 039 251, available
Monday to Friday, from 9AM to 5PM AEDT.
2

Table of Contents
Important Safety Rules
Check Prior to Operation
Operation Instructions
Towing the Log Splitter ..................
Log Splitter Troubleshooting
Maintenance, Storage & Essential Checks
Log Splitter Components
Log Splitter Specifications ..................
Warranty & Service Information
Accessories
......................................... 4-6
......................................... 7
............................................. 8
.......................... 9
....................................... 10
.................................. 14
................... 11
........... 12
....................... 15-17
........................................................... 18
Risk Register ......................................................... 13
3

Important Safety Rules
WARNING
1.) Read this manual completely.
-Serious injury or death can result if safety instructions are not fol-
lowed.
-Everyone who operates this log splitter must read and completely
understand all safety rules, operating instructions, and maintenance
instructions.
-You must be 18 or older to operate this machine and in sound
mind, free of the influence of medication, drugs or alcohol. Keep
untrained people away.
2.) Crush hazard.
The Crush Hazard Zone is between the Splitting Wedge (8) and the
Splitting Table (22). The Splitting Wedge (8) can cut through skin
and break bones. Make sure hands are clear of crush hazard zone
when log splitter is in operation.
3.) Flying objects.
-Pieces of wood may fly out while splitting. Wear safety glasses.
Serious eye injury can occur if safety glasses are not worn.
-Serious accidents can happen when other people are allowed
inside the safety and operator zone. Keep everyone else out of the
safety and operator zone while operating log splitter. See page 7 for
operator zone.
4.) Skin injection hazard.
-High pressure fluid can inject under skin resulting in serious injury
including amputation.
-If skin injection happens, seek immediate “Surgical Treatment”.
Call 000
-Make sure all fittings are tight before starting the log splitter.
Relieve system pressure before servicing by turning off the log
splitter and moving Control Valve Lever (7) back to the neutral
position.
-Do not check for leaks with hand. Instead, use a cloth or place a
piece of card-board under the unit to check for leaks.
Safety Rules Continued...
4

Important Safety Rules
WARNING
-Position muffler at least 7 feet from combustible objects.
-Before adding fuel, stop the engine and keep heat, sparks, and
flame away. Do not add fuel when engine is running or still hot. No
smoking near engine.
-Do not pump fuel directly into engine at gas station. Static charge
can build and ignite fuel. Use an approved fuel container to transfer
petrol to the engine. Wipe up fuel spills immediately.
-Store and handle fuel outdoors. Gasoline vapors can ignite if they
collect inside an enclosure. Explosion can result.
-Do not change or add to exhaust system. Fire can result.
-Do not change or add fuel tanks or fuel lines. Fire can result.
-Before each use, check fuel tank and fuel lines for leaks. Any fuel
leak is a fire hazard. Fix any fuel leaks before starting engine.
-During transportation take precautions to make sure machine will
not tip over and cause a fuel leak and fire hazard. Engine fuel lever
should be turned to off while transporting this log splitter.
5.) Risk of fire and explosion.
Hot exhaust fumes from the engine can cause a fire. Gasoline is
highly flammable and explosive. You can be burned or seriously
injured when handling fuel.
6.) Breathing hazard.
Poisonous fumes from the engine can kill you. Do not operate
indoors even if ventilated. This product is intended for outdoor
use only.
7.) Hot muffler.
You can be burned by the muffler. Do not touch muffler during
or immeiately after use.
5

WARNING
Read & thoroughly understand the following Operational Warnings
before operating this RedGum Log Splitter.
OPERATIONAL WARNINGS
·Intended purpose: This product is designed as an outdoor product to split wood
logs to use as fuel in a fireplace or a woodstove. Never use the log splitter for any
other purpose than splitting wood.
·Always place logs so the axehead/Splitting wedge splits with the wood grain and
not across the wood grain.
·ALWAYS inspect log splitter before using to ensure it is in good working
condition.
·Replace or repair damaged or worn parts immediately.
·ALWAYS check and tighten fasteners, hardware and assembled parts before
operation.
·ALWAYS operate log splitter on firm, clear and level ground
·ALWAYS set up a SAFETY ZONE restricting onlookers to at least 3m away from
the log splitter when in use.
·ALWAYS remove split wood from around the log splitter immediately after it’s
spilt into smaller pieces so that you don’t stumble over it.
·Do NOT exceed equipment maximum splitting capacity by altering component
settings.
·Do NOT operate the log splitter at night, only during daylight hours.
·Shut engine off before leaving log splitter unattended.
Keep this operations manual handy for future reference
and re-read this Owner's Manual periodically.
•Check Hydraulic Oil levels with a Dipstick
•Check engine oil level by sighting engine dip stick.
•Closely inspect all log splitter components. If you sight damaged components then contact
your RedGum dealer before use.
•Always wear safety glasses while operating this log splitter. It’s also recommended to
wear Ear Muffs, Steel capped boots, Tight fitting gloves and Suitable clothing - A free from
hanging strings, jewelery or other items that could get caught up in moving parts. If you have
long hair make sure it is tied back and kept out of the way of moving parts.
RedGum Splitters are assembled and ready for use however:
6

Serious accidents can happen when other people are allowed inside the OPERATOR ZONE
(see following diagram). Keep everyone out of the operator zone while operating the log
splitter. ALWAYS set up a SAFETY ZONE restricting onlookers to at least 3 meters away
from the log splitter when in use.
PRE-OPERATION CHECKS
Essential checks to be carried out before each use:
What When How
Hoses Each Use
Nuts & Bolts Check for loose bolts. Tighten before operating.
Beam
4V]PUN7HY[Z Clear debris
Hydraulic Fittings Inspect for cracks & leaks. Replace all damaged
fittings before starting the engine.
Each Use
Each Use
Each Use
Each Use
Inspect for exposed wire mesh & leaks. Replace
all worn/damaged hoses before starting engine.
Apply grease to beam surface (if required).
It is important to follow the below check-list before operating the machine:
Read the Operations Manual carefully to understand the risks associated with using
the logsplitter.
Ensure that the machine is operated in a well-ventilated environment.
Wear appropriate protective gear to protect your hands, eyes, feet and body.
7

OPERATION INSTRUCTIONS
Proper Operation of the Log Splitter
Always follow Operational warnings & check-list before operating!
1.) Carefully place a log on the Splitting Table (10). Maximum length of the log
suitable for the logsplitter is 60cm.
2.) Start Engine by using the following instructions:
a.) Turn the engine switch to 'ON' position.
b.) Slide the choke lever away from the fuel tank to activate the choke.
c.) Turn the fuel tap on.
d.) Raise the engine revs by sliding the throttle lever away from the fuel tank.
Always use full throttle when using the machine.
e.) Pull the starter cord handle lightly until resistance is felt, then pull briskly.
f.) When the engine starts to run, deactivate the choke by sliding the lever
towards the fuel tank.
4.) Start the splitting procedure by pushing and holding the Control Valve Lever
(7) forward. Please note the Splitter Wedge (8) only moves downward when you
are holding the lever forward. When you let go of the Control Valve Lever (7) the
Splitting Wedge (8) stops immediately for safety reasons.
5.) To return the Splitting Wedge (8) to its starting position, simply pull the Control
Valve Lever (7) backwards. Please note the Splitting Wedge (8) returns back to
the original starting position automatically after the Control Valve Lever (7) is
returned to its neutral position. Also, please note that for safety reasons, the
Splitting Wedge (8) stops approx. 3-4cm from the Splitting Plate.
6.) Always make sure that the operator zone is clean and free from split wood
and debris.
7.) Repeat the above steps as required.
PREPARING THE LOGSPLITTER FOR USE
Before operating the logsplitter, make sure that both the supports legs are firmly set on
the ground and that both the tired have been blocked.
This is necessary to prevent unnecessary movement of the log on the Logsplitter
Splitting Table (10).
8

Towing incorrectly is a serious risk and can result in injury or death.
Please read the following Towing Warnings:
Remember to turn the engine and fuel tap to the off position prior to towing. This is to
prevent flooding of the engine.
•IMPORTANT: Log Splitter is not approved or designed to be towed on Public Roads.
•Serious injury or death can occur if Towing Safety Rules are not followed.
•Review Towing Safety Warnings as mentioned in your Owner's Manual.
•Drive safely. Be aware of the added length that the lifter splitter adds to your vehicle.
•Never ride on or transport cargo on the lifter splitter.
•Always secure and lock the lifter splitter to the vehicle hitch before towing.
•Drive the vehicle only after the lifter splitter is securely attached.
•Turn off the vehicle if leaving the lifter splitter unattended.
•Choose a leveled surface to operate the lifter splitter.
•Block the lifter splitter's wheels to prevent any unattended movement.
•Never tow or operate this splitter while under the influence of alcohol, drugs or
medication.
•Avoid large holes and ditches when towing the lifter splitter in a vehicle.
•Always tow at a reduced speed on rough or uneven terrains, along the side of creeks,
ditches and hillsides.
•Do not exceed a speed of 45KM/H when towing the lifter splitter.
•Read the below details to know further instructions regarding the logsplitter.
WARNING
TOWING THE LOGSPLITTER
The RedGum Super VHD 32000 Logsplitter has a 50mm Ball Coupler with a tow bar (3)
which can be attached to the back of your ATV or Ride On Mower to tow
the machine around your property. This tow bar is attached to an efficient Jockey Wheel,
which allows you to easily move the machine without any problems! The RedGum Super
VHD 32000 Logsplitter is not suitable for towing on the road. The logsplitter is only
suitable for low-speed towing around your property. The maximum rated
towing speed for the RedGum Super VHD 32000 Logsplitter is 45km/h.
9

LOGSPLITTER COMPONENTS
1) Coupler: Attaches the log splitter to the ball.
2) Jockey Wheel
3) Tow Bar
4) Engine: The air-cooled Honda GX200 powers the hydraulic pump
5) Wood Tray: Can hold a maximum of 75kgs
6) Hydraulic Cylinder: Internal diameter of 4.5 Inch
7) Control Valve Lever: Controls the forward and backward movement of splitting
wedge.
8) Splitting Wedge: Features wedge wings and tapered ends making splitting
easier.
9) Counterweight Wire
10)Splitting Table
11)Hydraulic Lifting Plate
12)Tires: 16" heavy-duty wheels capable of maximum speed of 45km/h (note this
logsplitter is not suitable for road towing)
13)Oil Tank: 20L
14)Tool Box
15)Gear Pump: Pumps the hydraulic oil through the system.
10

1.) Fuel Cap
2.) Fuel Tank
3.) Oil Drain Plug
4.) Oil Filler Cap/Dipstick
5.) P.T.O Shaft
6.) Muffler
7.) Spark Plug
8.) Choke Lever
9.) Fuel Valve Lever
10.) Starter Grip
11.) Recoil Starter
12.) Air Cleaner
ENGINE COMPONENTS
2
1
34
5
7
6
12 11
10
8
9
For more information on Engine Operation & Engine Maintenance,
please refer to engine manual supplied with the log splitter.
LOGSPLITTER SPECIFICATIONS
Splitting Force................................................................. 32000 kgs
Cycle Time..................................................................... 14 seconds
Hydraulic Tank capacity.......................................................... 20L
Max. Log Length.............................................................. 60cm (24")
Maximum Pressure............................................................ 3000PSI
Gear Pump............................................................ 11GPM, 2-Stage
Wheel Size................................................................................ 16"
Tow Bar Hitch Type........................................... 50mm Ball Coupler
Jockey Wheel.............................................................................. 6"
Lifting Capacity............................................................ Up to 100kgs
Max. Towing Speed............................................................ 45km/h
Hydraulic Filtration Capacity............................................ 25 microns
11

Oil Filter
Your machine is fitted with an Oil Filter. After the first 25 hours of operation, change the oil filter.
Thereafter, change oil filter after every 100 hours of use (or change it seasonally).
MAINTENANCE, STORAGE & ESSENTIAL
CHECKS
Before performing maintenance, the log splitter must be placed in maintenance mode. To
do so, follow the below steps:
1.) Turn off engine
2.) Move the Control Valve Lever forward and backward to relieve Hydraulic Pressure and
leave in neutral position.
3. After performing maintenance, make sure all guards, shields and safety features are put
back in place. Failure to follow this warning can result in serious injury.
Storage
•Before storing, make sure the log splitter is clean and dry.
•Lightly lubricate all log splitter surfaces and moving parts to prevent rust.
•Store indoors or protected area and preferably under the RedGum Cover when the log splitter is
not being used.
•It is essential to fully retract the splitting wedge, ensuring no silver part of piston rod is exposed
to the elements.
COMPONENT L/S C/S Interval
1 2 3 4
Complete Unit
On Off Switch
Choke/Primer
Engine Oil
Throttle Lever
Cables and
Connections
Fuel Filter
Carburettor
Air Filter
Clutch
Spark Plug
Cooling Fins
Starter Cord
Starter Housing
Vents
Spark Arrestor
All Screws, Nuts &
Linkage
I I I/C I
I I I I
I/A I I/A I
I R R I
I I I I
I/A I I/A I
I I R
T T T
I I C/R I/C
I I I
I I/C R I
I I/C C C
I I I I
I I/C C C
I I I/R I
I I I I
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
MAINTENANCE SCHEDULE
COMPONENT L/S C/S Interval
1 2 3 4
Anti Vibration
Mounts
Hydraulic Oil
Hydraulic Oil Pump
Hoses
Hydraulic Fittings
Beam
Control Valve
Belts
Blades
Flails/Hammers
I I I
I I I/R I
I I I I/A
I I I I
I I I/C I/C
I I I I
I I I I
I I I/A
I I I/R
I I I/R
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
Yes
No
No
No
No
No
No
Yes
Yes
Yes
LEGEND: L/S = Log Splitter, C/S = Chipper Shredder
I = Inspect, T = Tune, R = Replace, C = Clean, S = Sharpen, A = Adjust, L
= Lubricate
INTERVAL:
1 = Pre Delivery, 2 = First Service, 3 = Dealer Service, 4 = Every time the
machine is used
DEALER SERVICE:
WARNING
Skin Injection Hazard - Refer to your Engine Manual for further instructions
High pressure fluid can inject under the skin and can result in serious injuries!
−Make sure all hose and control fittings are tight before applying pressure. Relieve
system pressure before servicing, as explained in point 2 at the top of the page.
−Do not check for leaks with your hand. Instead, place a piece of cardboard under the unit
to check for leaks.
−If skin injection occurs, seek immediate 'Surgical Treatment'. Call 000.
12

RISK REGISTER
Level of Risk Hazard Dangers
associated
with the Risk
Measures to avoid/control this hazard
LOW While assembling the
Logsplitter, there is a risk
of injury to the body due to
lifting and installing of
heavy components
Injury to back,
Sore arms
Use the correct tools to assemble the
logsplitter.
Wear appropriate gloves while
assembling the logsplitter.
LOW While operating the
logsplitter, there is a risk of
fingers being jammed
against the Splitting Table
and the block of wood.
Injury to fingers
and hand
Wear appropriate Safety Gear while
operating the logsplitter.
Only operate the machine within the
defined Logsplitter Operating Zone.
LOW While operating the
logsplitter, there is a risk of
falling over blocks of wood
present in the Operating
Zone
Injury due to
fall, bruises
and sprains
Make sure that only the operator of the
machine is present in the defined
Logsplitter Operating Zone.
Wear appropriate Safety Gear while
operating the logsplitter.
LOW While operating the
logsplitter, there is a risk of
inhaling the exhaust fumes
of the engine
Nausea Make sure to only operate the machine in
an outdoor environment, and within the
defined Logsplitter Operating Zone.
LOW While operating the
logsplitter, there is a risk of
getting burned by hot oil
from the engine
Burns on the
operator’s skin
Wear appropriate Safety Gear while
operating the logsplitter.
The Oil Hoses on the logsplitter have
Burst Protection for added safety
LOW Maintenance and
Troubleshooting of the
Logsplitter
Read the Engine Manual and Operations
Manual carefully before Maintenance and
Troubleshooting of the machine.
LOW Preparing the logsplitter
for towing
To prevent fatigue or body strains, the
RedGum Super VHD 32000 Logsplitter
is equipped with a Tow bar and Coupler
for easily attaching it to the back of your
ATV or Ride On Mower. This machine is
not suitable for road-towing and should
only be towed around your property. The
maximum rated towing speed for this
machine is 45km/h
RedGum Logsplitters are safe and efficient machines, and are the best at getting the
job done. Our machines utilize the latest innovations in technology to give you a safe
yet comfortable wood-splitting experience. The above Risk Register provides you with
a list of some risks associated with operating this logsplitter. Make sure to read the
Operations Manual and Engine Manual carefully before operating this logsplitter, and
wear appropriate Safety Gear at all times.
13

LOG SPLITTER TROUBLESHOOTING
Problem
Cylinder rod & splitting wedge will not
move
Solution: A, D, E, H, J
Slow cylinder shaft speed when
extending or retracting
Solution: A, B, C, H, I, K, L
Wood will not split or splits extremely
slowly
Solution: A, B, C, F, I, K
Engine bogs down during splitting Solution: G, L
Engine stalls under low load condition Solution: D, E, L, M
Cause Solution
A - Insucient oil to pump Check oil level in reservoir
B - Air in oil Check oil level in reservoir
C - Excessive pump inlet vacuum Check pump inlet hose for blockage or
kinks
D - Blocked hydraulic lines Flush & clean the splitter hydraulic
system
E - Blocked control valve Flush & clean the splitter hydraulic
system
F - Low control valve setting Adjust control valve with a pressue
gauge
G - High control valve setting Adjust control valve with a pressue
gauge
H - Damaged control valve Return control valve for authorised
repair
I - Internal control valve leak Return control valve for authorised
repair
J - Internal cylinder leak Return cylinder for authorised repair
K - Internally damaged cylinder Return cylinder for authorised repair
L - Engine control out of adjustment Return for authorised repair
M - Engine is loaded during idle down
mode
Use shorter log length (24” or less) to
allow engine to speed up before contact
Solution
14

WARRANTY AND SERVICE INFORMATION
Congratulations on the purchase of your new RedGum product. RedGum
Products will assist you to complete the “job at hand” in an economical, safe
and efficient manner.
This brochure explains the Warranty and Maintenance information for your
product. This combined with your Owner’s Manual and the knowledge and
expertise offered to you by your respective RedGum Dealer should provide you
with the confidence that your decision to purchase a RedGum product was a
good one.
STATEMENT OF WARRANTY
This statement of warranty applies to all RedGum products (offered by the
manufacturer, RedGum Products). The manufacturer provides this warranty to
the initial purchaser of this product (who has purchased it from an authorised
RedGum Products dealer) for a period commencing from the date of purchase.
If the product is found to be defective, in RedGum Products'
opinion (due to a fault of the manufacturer) within the Warranty
Period, RedGum Products will carry out the repair or
replacement to the customer Free of Charge, provided:
•The fault is reported directly to the place of purchase.
•Sufficient proof of purchase is provided.
•The fault is not caused by misuse, neglect or incorrect adjustment by the
user.
•The failure has not occurred through normal wear and tear.
•The product has not been serviced, repaired or alterations made by any
one not authorised by RedGum Products to do so.
The Warranty Periods
The warranty periods mentioned below commence on your date of purchase:
Customer Type RedGum
Splitter
RedGum
Chipper
Private/Domestic 12 Months
Commercial 3 months 3 Months
NOTE:
-Engines are covered by the respective original
equipment manufacturers warranty and claims are made
direct to the manufacturer agent.
-Replacement parts and accessories fitted during a
repair under terms of warranty will enjoy cover for the
remainder of the warranty period of the finished product.
24 months
Please note that Warranty Claims for your RedGum product can
only be made through an Authorised RedGum Dealer
15

WHAT IS NOT COVERED BY WARRANTY
The following items are not covered by
this warranty:
•Normal maintenance items which become worn
through use, including, but not limited to, belts,
blades, oil, blade adapters, filters, rewind springs,
spark plugs, starter ropes, clutches and sprockets.
•Natural discoloration of material due to sunlight.
•Engines not manufactured by RedGum Products,
these items are covered by the respective original
equipment manufacturers’ warranty, all claims must
be sent to the appropriate manufacturer’s agents.
•Using stale or contaminated fuel in the product.
•Damage or failure caused by accident, misuse
and/or neglect, including, ingress of dirt, abrasives,
moisture, rust & corrosion, and damage due as a
result of inadequate maintenance.
•Failure to operate or maintain the unit in
accordance with the Owners/Operators manual, this
handbook or instruction given by a RedGum dealer.
•Alterations or modifications that change the
intended use of the product or affect the product's
performance, operation, safety or durability, or
causes the product to fail to comply with any
applicable laws.
•Damage due to incorrect usage such as incorrect
log placement (as shown in the product's respective
Owner's Manual)
•Additional damage to parts or components due to
continued use occurring after any of the above.
Spark Plugs: Periodic replacement is required to
ensure maximum engine performance and best
fuel economy.
Induction/Combustion System: The removal of
deposits and cleaning may be required from time
to time and should be performed as necessary.
Tyres: Tyres are subject to wear and if they come
in contact with external objects, they can deflate.
A flat tyre is not a warrantable item.
External Surfaces, Paint, Trim and other
Appearance items: Are affected by normal wear
and tear and exposure to environmental
conditions. A charge will be made for paint and
trim items that require attention due to causes
outside the manufacturer’s control.
Hydraulics: Changing hydraulic fluids
The frequency of replacement, repair or
adjustment will depend mainly on where and how
you use your product, weather, atmospheric and
environmental conditions and frequency of use.
CUSTOMER RESPONSIBILITIES
The customer must provide to an authorised
RedGum Dealer their proof of purchase
information such as a receipt.
The product must exhibit reasonable care in the
maintenance, operation, storage and general
upkeep practices as explained in the maintenance
section of the Owners/Operators Manual or this
handbook. This includes the whole product or any
general wear item or component on the product.
Any costs incurred to obtain warranty
consideration or services is the customer’s
responsibility, including shipping and handling,
travel expenses, lost time, lost production or
pickup and delivery.
YOUR RIGHTS AS A CUSTOMER
The New Product Warranty that is provided by
RedGum Products is in addition to the rights and
remedies conferred on consumers by the relevant
authorities and/or legislation. The warranty does
not affect those rights or remedies, except to the
extent that their application may lawfully be
excluded. Any consequential, direct or incidental
loss or damage is not covered by the warranty.
Any statutory or other rights or remedies available
in connection with a claim for such loss or damage
should be pursued separately.
ITEMS FOR WHICH A CHARGE WILL BE
MADE
The following list is a guide to the types of items for
which a charge will be made (unless failure is
caused by a defect in the manufacturer's materials
or workmanship).
Service: Maintenance servicing and all parts and
fluid replaced in line with the maintenance schedule
shown in this handbook.
Mechanical Adjustments: Including engine tuning,
adjusting brakes, belts & clutches etc.
Drive System: Sprockets, belts, clutches, pulleys
and bearings all wear and will require replacement.
Cutting Equipment: Blades, cutting discs and
hammers wear during use and sharpening/
replacement is required as a matter of normal
maintenance.
16

WHERE TO GO FOR WARRANTY REPAIRS
Take your product to any authorised RedGum Dealer if it needs
warranty repairs. All authorised RedGum Dealers will honour the New
Product Warranty, and will repair, replace or adjust free of charge any
part of your product that is defective in factory materials or
workmanship. Please note that RedGum is unable to reimburse the cost
of repairs carried out during the warranty period by a repairer who is not
an Authorised Servicing Dealer.
To find your nearest Authorised RedGum Products dealer, visit:
www.RedGumProducts.com.au or Call Toll Free 1300 039 251
Date of Purchase:..............................................................................................
Serial Number:...................................................................................................
Purchased from:................................................................................................
The manufacturer reserves the right to make improvements in design
and/or changes in specifications at any time without incurring any
obligation to install them on units previously sold.
Engine Number:.................................................................................................
Visit www.RedGumProducts.com.au • Call 1300 039 251
WARRANTY INFORMATION
Please note down for future reference:
RedGum Splitter Model: RedGum SUPER VHD 32000 Logsplitter
17
NOTES
...........................................................................................................................................
...........................................................................................................................................
...........................................................................................................................................
...........................................................................................................................................
...........................................................................................................................................

High quality hydraulic oil fluid - ideal for topping up your
RedGum logsplitter’s hydraulic reserve, when required.
3.) RedGum Logsplitter Dust Cover - RRP $99
Heavy-duty 200D logsplitter cover for superior protection
against dust, dirt and heavy rain!
6.) RedGum Vertical Splitting Plate - RRP $179
A new innovation by RedGum, this accessory is
compatible with most non-lifter RedGum
logsplitters. As an alternative to the Log Turn
Table, this stationary plate makes vertical splitting
of logs super simple and pain-free!
5.) Dual Purpose Log Lifter & Roller - RRP $189
This dual purpose log lifter & roller allows you to
effortlessly roll large logs and keep them off the mud!
Sturdy dual-foot design prevents the handle from digging
into the ground.
Improves productivity by preventing split logs from falling to the
ground. It also helps reduce the effort of picking up split logs that
require further splitting. Compatible with most RedGum splitters.