TOPMAQ LOHA2110 User manual

I
INSTRUCTIONS FOR
150kg Log Stand
IMPORTANT:PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF
THIS PRODUCT
GENERAL INFORMATION
These instructions accompanying the product are the original instructions.This
document is part of the product,keep it for the life of the product passing it on to any
subsequent holder of the product. Read all these instructions before operating or
maintaining this product.
This manual contains all the necessary information to ensure it correct and safe use.
By following all the general safety instructions contained in this manual,it will ensure
both product and operator safety,together with longer life of the product itself.

1
1. INSTRUCTION
1.1 SCOPE
This log stand is manually operated saw horse,designed to enable the efficient and
safe sawing of logs and branches.
Its powder coated steel construction means it is suitable for home/DIY use by
professional aborists for the sole purpose of sawing logs upto 150kg in weight.
1.2 SPECIFICATION
Max. Log length …………………………………………………………………… 4M
Min.log diameter ………………………………………………………………… 50mm
Max.log diameter …………………………………………………………… 250mm
Max.log.log weight …………………………………………………………… 150kg
Dimensions(L x W x H) …………………………………………… 1100x380x900mm
Weight ………………………………………………………………………… 10.8kg
…………………………………………………………………… 12kg(gross)
1.3 HANDING&STRORGE
Although this machine is strong and durable,care must still be taken when handing
and lifting.Dropping this machine will have an effect on the fixing used in it’s
construction and may also result in personal injury. This machine is not a toy and
must be respected.
This product is likely to be used outside and be subjected to all number of weather
variables.
Care should be taken to avoid leaving if exposed to the elements as this could cause
rusting which will weaken the product. Best policy is to store in a dry location when
not in use.

2
2.TECHNICAL DESCRIPTION
2.1 INDENTIFICATION
○
1Log support frame
○
2Cross bar
○
3Teeth
○
4Base
○
5Diagonal brace
○
6Brace pin

3
3. OPERATING THE LOG STAND
3.1. OPERATING THE LOG STAND
Ensure that the ground on which you are placing the log stand is firm and level.
With the log stand lying on the ground, lift the log support frame into the vertical
position.
Rotate the diagonal braces from their stored position and fit the holes in the ends of
the braces over the pins on the inside of the forward part of the base.

4
4. OPERATING THE LOG STAND
4.1 OPERATING THE LOG STAND
Insert the log through the teeth in the direction shown,until approximately 1/3 of the
log length is forward of the log support frame. The log should be angled so that the
short end of the log is slightly lower than the rear.
Rest the log on the lower teeth on the cross bar and slowly release the weight so that
the upper teeth engage with the log.
The log should be approximately horizontal with 1/3 of its length forward of the log
support frame.
WARNING: With heavy and long logs,the weight of the log is sufficient to engage the
teeth. Do not press down on the long overhanging end of the log as this may result in
damage to the log stand.
Begin by cutting the initial few logs from the long over hanging end of the log and cut
successive logs so as to maintain length forward to the log support frame and 2/3

5
behind.
WARNING:Always cut in a downward direction as shown.
WARNING: Check that the log is secure and the log stand is stable before beginning
to cut.
IMPORTANT: Please read these instructions carefully. Note the safe operational
requirements,warnings and cautions. Use the product correctly and with care for the
purpose for which it is intended. Failure to do so may cause damage and/or personal
injury and will invalidate the warranty. Please keep these instructions safe for future
use.
4.2 MAINTENANCE
This log stand is load bearing, therefore it is essential to routinely check the fixings
and overall condition of the steel work. Do not use the log stand if it exhibits andy
signs of fatigue or wear. Apply common sense and if in doubt, do not use it, contact
retailer for further advice.
4.3 DISPOSAL
At the end of the log stand’s working life,or when it can no longer be repaired,ensure
that it is disposed of according to national regulations.
Contact your local authority for details of collection schemes in your area.
In all circumstances:
Do not dispose of in domestic waste.
Do not incinerate.
Do ot abandon in the environment.