Remington HyperFlex SHAVE & TRIM XR1390AU User manual

2 YEAR WARRANTY
To register your product go to
www.remington-products.com.au
XR139 0AU
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE

2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should
always be observed, including the following.
READ ALL INSTRUCTIONS BEFORE USING
For additional protection, the installation of a residual
current device (rcd) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
WARNING - TO REDUCE THE RISK OF BURNS,
ELECTROCUTION AND FIRE OR INJURY TO PERSONS
DANGER - As with most electrical appliances, electrical
parts are electrically live even when the switch is off.
• The appliance should never be left unattended when plugged
into a power outlet, except when charging the appliance.
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
• Never operate this appliance if it has a damaged cord or
plug, if it is not working correctly, if it has been dropped or
damaged, or dropped into water. If the supply cord or plug
of the appliance is damaged it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard. It cannot be repaired. Keep the
cord away from heated surfaces.
• Charge, use and store the product at a temperature between
0°C and 32°C.

3
• Do not use outdoors or where aerosol (spray) products are
being used, or where oxygen is being administered.
• Do not use this appliance with damaged or broken tracks or
cutters, as injury may occur.
• Do not plug or unplug the appliance with wet hands.
• For household use only.
• Do not place or store the appliance or charging adaptor
where it can fall or be knocked into a sink or bath.
• Do not place in or drop into water or any other liquid.
• If an appliance falls into water, “unplug it” immediately. Do
not reach into the water.
• Unplug the charging adaptor from the electrical outlet
immediately after fully charging.
• Do not use while bathing or in the shower.
• Unplug and switch off this appliance before cleaning it.
• Use this appliance only for its intended use as described in
this manual.
• Do not use attachments not recommended by Remington.
• Never drop or insert any object into any opening of this
appliance.
• Always store the charging adaptor in a moisture-free
location.
• Do not use on people who are asleep.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(Residual current device) be installed to protect all bathroom
power outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS

4
XR1390AU SHAVE & TRIM
USE & CARE INSTRUCTION MANUAL
Thank you for purchasing your new Remington® HyperFlex Shave & Trim.
Inside this manual you will find tips on using and caring for your shaver.
KEY PARTS
1. Pivoting head & cutter assembly
2. Individual flexing heads
3. Hairpocket
4. Pop-up trimmer (rear)
5. On/Off push button
6. LCD display
7. Charging pins
8. Beard trimmer attachment
9. Beard trimmer comb
Also Includes
• Storage pouch
• Power adaptor
• Charging stand
• Cleaning brush
7
5
6
1
2
3
4
8
9

5
FEATURE XR1390AU
Power System Cordless
Initial Charge Time 24 Hours
Full Charge Time 90 Minutes
Cordless Shave Time 60 Minutes
Quick Charge Yes
Indicators LCD
Voltage Type Worldwide
Charging Stand Yes
Travel Lock Yes
Shaver head Replacement Part No. SPR-XRAU
Trimmer head Replacement Part No. SPR-XTAU
Power System: Cordless – shaver can only be used without the power cord. The
shaver will not run while it is charging on its charging stand.
Quick Charge: Shaver will charge long enough for one shave in 5 minutes.
Indicator: LCD Panel – displays the number of minutes of remaining battery power.
Voltage Type: Worldwide Voltage – shaver automatically adapts to an outlet
voltage between 100V and 240V.
Note: Some countries will require the use of a plug adaptor that is not included with
your shaver.
Travel Lock: To engage travel lock, press and hold the On/Off button for 3
seconds. To disengage travel lock, press and hold the On/Off button for 3 seconds.

6
CHARGING
1. Plug power adaptor into the charging stand. (Diagram A)
2. Plug power adaptor into wall outlet. (Diagram B)
3. Charge shaver for 24 hours before its first use. This first charge is important
to the shaver’s battery life. Note: During initial charge ignore the electronic
indicators as they are in “start up cycle”. (Diagram C)
4. Use shaver until recharge is required.
CAUTION!
• Make sure the shaver and your hands are dry when charging the shaver.
• Always charge the shaver in a cool, dry place.
SHAVING
1. Press power button to turn on. (Diagram D)
2. Shave face and neck using short, circular strokes. (Diagram E)
3. After shaving, turn the shaver off. (Diagram D)
B
E
D
A B C

7
SHAVING TIPS
• Remington HyperFlex shavers are showerproof. You may use shaving foam or
cream with your shaver. You may also shave in the shower.
• Wait at least 15 minutes after getting up before shaving, to ensure your face
is free of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so that all three heads are
touching the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for
them to enter the cutting chamber.
• Use moderate to slow, circular stroking movement.
• The use of short, circular motions in stubborn areas may obtain a closer
shave, especially along the neck and chin line.
• Do not press hard against the skin to avoid skin irritation and/or damage to
the rotary heads.
TRIM
Beard Trimmer:
To remove the shaver head, simply pull upwards from the neck of the shaver for
easy release.
To attach the beard trimmer attachment, align it with the neck attachment cavity so
that it clips into position.
The beard trimmers micro setting zoom comb can be adjusted to suit your required
length setting type of between 2-6mm. The setting can be adjusted by turning the
wheel either left or right.
Without the beard comb attachment, the length of hair cut will be 0.4mm.
Pop-up Trimmer:
1. Push trimmer release button to engage trimmer. (Diagram F)
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down. (Diagram G)
F G

CLEANING & CARE
The shaver is a washable apliance. The head and body may be cleaned
under warm water.
NOTE: **When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.**
CAUTION!
• When cleaning the external surfaces of the shaver, do not use strong
detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
NOTE: **The shaver head and neck assembly is designed to be detachable
from the shaver body. Simply pull upwards from the neck of the shaver for
easy release. To reattach neck, align it with the neck attachment cavity so
that it clips back into position.**
Daily:
1. Locate the detachment grooves on the head & cutter assembly. Gently pull to
detach the hair pocket from the neck assembly. (Diagram L)
2. Tap out excess hair shavings.
3. Rinse the head of the shaver in running water.
4. Gently reattach the hair pocket to the neck assembly until it locks in place on
all three sides. The hair pocket may be reattached in any configuration.
8
1. Head & cutter (hair pocket) assembly
2. Detachment grooves
3. Neck assembly
4. Neck attachment cavity
5. Beard trimmer attachment
5
1234

Cleaning the Beard Trimmer Attachment
Clean the beard trimmer attachment with the cleaning brush provided, brush away
hair clippings from the blades, and top of trimmer handle.
NOTE: If you rinse these attachments with cool or warm water (never use hot
water) or use it in the shower then the blades will need to be lubricated with light-
grade oil or sewing machine oil (1-2 drops over the cutters) every month.
Weekly:
1. Perform the daily cleaning steps 1 and 2.
2. Remove the hair pocket from the head & cutter assembly. (Diagram L) Place
the body of the shaver aside.
3. Slide the blue cutter support frame upwards towards the direction of the two
cutters to release it from the assembly. (Diagram M)
4. Lift and remove the cutter support frame away from the cutters.
5. Remove the cutters. (Diagram N)
6. Thoroughly rinse away any debris from inner and outer cutters with warm
water.
7. Replace the inner cutters. (Diagram O) The inner and outer cutters are colour
coded (orange, blue and black) to ensure each cutter is returned to its original
and most effective position on the cutter assembly.
8. Hold the cutter support frame with the raised center section facing upwards.
Place it over the cutters so that the centre mouth opening is facing the blue
cutter. Slide the cutter carrier towards the blue cutter until the locking tab
locks under the centre triangle. (Diagram P)
9. Lubricate each cutter with Remington Shaver Saver (SP4).
10. Gently reattach the hair pocket to the neck assembly until it lock in place
on all three sides. The hair pocket may be reattached in any configuration.
(Diagram Q)
** Pop Up Trimmer: Lubricate teeth with oil every six months
9
LMNO
Q
P

REPLACING YOUR HEADS & CUTTERS
Please refer to the shaver grid on page 5 of this manual that lists the correct
replacement part number for your shaver.
It is very important to replace your head and cutters when necessary to ensure
a close, comfortable shave without irritation. We recommend they be replaced
every 12 months. Here are some signs of head and cutter wear, indicating that
replacement is needed:
• Irritation: As the heads get excessively worn you may experience some skin
irritation. This would be especially noticeable when you apply moisturizing
lotion.
• Pulling: When the cutters wear you may feel a sense of pulling and a loss of
closeness when you shave. This is an indication that it is time to replace your
heads and cutters.
Replacement heads & cutters may be obtained from your local retailer, or
directly from Remington®. Simply fill out the enclosed accessory order form or
alternatively your order can be processed over the phone via the Remington®
Service Hotline - refer to page 12.
This product is not suitable to use in a bath.
This product conforms to radio frequency interference requirements
Any product purchased and used commercially carries a limited 90 Day Warranty.
MONEY BACK OFFER – AUSTRALIA / NEW ZEALAND ONLY
If within 60 days you are not fully satisfied with your Remington® shaver, just return the shaver
with this completed coupon and a copy of your Australian/New Zealand purchase receipt to
Remington®. In return, we will send you a cheque for the full purchase price of the shaver.
Please allow 6-8 weeks for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
Contact No: Area Code: Ph:
Product Model number:
Is this the first Remington shaver you have owned/purchased? Yes No
What is the reason you are returning this product?
10