Rentokil Vertex GeyserJet Series User manual

GeyserJet™ Series
2100 NW 33rd St • Pompano Beach, FL 33069 • 844.432.4303 • vertexaquaticsolutions.com
Drawings are for illustration only and not to scale. Installation of fountain equipment shall be in accordance with manufacturers specifications.
Fountain Only
With LED Lights
Motor HP 2 2 2 3 3 3 5 5 5 7.5 7.5 7.5 10 10 10 15 15 15 20 20
Volts 230 230 208 230 230 208 230 230 208 230 230 208 230 230 208 230 230 208 230 208
Phase 13313313313313313333
AMP 14 8 9 17 10 13 28 17 21 42 25 28 51 32 37 72 47 54 61 70
HT. A 8' 8' 8' 12' 12' 12' 18' 18' 18' 22' 22' 22' 25' 25' 25' 28' 28' 28' 30' 30'
Dia. B 4' 4' 4' 4' 4' 4' 5' 5' 5' 6' 6' 6' 6' 6' 6' 8' 8' 8' 8' 8'
43W LED Lights 22222233344444455566
Total Watts 86 86 86 86 86 86 129 129 129 172 172 172 172 172 172 215 215 215 258 258
AMP Draw 0.8 0.8 0.8 0.8 0.8 0.8 1.1 1.1 1.1 1.5 1.5 1.5 1.5 1.5 1.5 1.8 1.8 1.8 2.2 2.2
CHECK EITHER WITH OR WITHOUT LIGHTS

2100 NW 33rd St • Pompano Beach, FL 33069 • 844.432.4303 • vertexaquaticsolutions.com
*Vertex reserves the right to improve and change designs and/or specifications without notice or obligation.
GeyserJet™ Specs
FLOTATION SYSTEM
Rotocast polypropylene with ultraviolet inhibitors added for extended protection against warping/cracking. Each seamless,
watertight section is equipped with threaded brass insert and expanding type fill-plug to add water ballast and leveling control.
PUMP/MOTOR
____HP, ____Volt, ____ Phase stainless steel, sealed UL listed submersible motor. Submersible turbine pump shall be of
100% 304 stainless steel construction, with driveshaft of 416 stainless steel and equipped with sand collars for maximum
protection against abrasives. Pump and motor are water cooled and lubricated. Use of oil-filled motors/pumping systems are
not acceptable due to need for regular replacement of oil, O-rings, and seals.
INTAKE SCREEN
Type 304, 18ga stainless steel, protects against foreign material entering pumping system.
FRAMEWORK
Type 304 stainless steel with welded joints and stainless steel fastenings.
LIGHTING FIXTURES
___ 43Watt, 120V clear, stainless steel LED light
fixtures with tempered lens and neoprene gaskets,
mounting brackets and fastenings of stainless steel.
See specification chart for suggested lighting package.
ETL listed.
DISPLAY HEAD
Head are water-level sensitive Geyser nozzle of 100%
brass construction, producing a heavy, active, and
highly aerated display. Display heads of plastics, PVC
and/or “thermoplastics” are unacceptable.
UNDERWATER ELECTRICAL CABLES
STW-A rated, stamped “water resistant”. ______' of
______ga-pump, ______' of _____ga-lights
FOUNTAIN CONTROL PANEL
Steel NEMA 3R enclosure
Surge/Lightning Protection
Capacitive motor starter (single phase units)
2 – 24 hour time clocks
Phase loss protection (3-phase units)
Circuit breaker – pump
Circuit breaker – lights (if equipped)
GFI protection – pump
GFI protection – lights (if equipped)
WARRANTY (PARTS)
Fountain - 4 years
Light Fixtures (excludes bulbs) - 2 years
Controls - 1 year

Fountain Install
2100 NW 33rd St • Pompano Beach, FL 33069 • 844.432.4303 • vertexaquaticsolutions.com
Drawings are for illustration only and not to scale. Installation of fountain equipment shall be in accordance with manufacturers specifications.
FOUNTAIN CONTROL PANEL
Warning - The fountain control panel must be installed by licensed electrician in accordance with article
682 of national electrical code.
Panel location is above any and all possible high water levels. Submergence of panel poses serious risk of electrical shock and
damage of fountain system. Failure may result in potentially hazardous conditions and/or failure of electrical inspection.
Consult authorities having jurisdiction (ahj) for specific local codes/restrictions. Vertex Aquatic Solutions accepts/assumes no
responsibility for installations not in accordance with local and/or national electrical codes.
SCOPE OF WORK - ELECTRICIAN
1.Mount NEMA 3R panel enclosure in
accordance with NEC 682 following
any additional local codes and/or
restrictions that exist.
2.Trench and bury sufficiently sized
conduit(s) from fountain panel to
water’s edge, extending conduit(s)
far enough into water to ensure no
submersible cable is exposed should
low water conditions arise.
3.Bring incoming power from power
source into the fountain panel.
Incoming voltage must match with
specifications of fountain panel
or failure will result, damaging the
system and voiding the warranty.
4.Pull submersible cable(s) from
fountain through conduit to control
panel and perform final connections
See Fountain Owner’s Manual for
details on installing the fountain
in your lake.
IMPORTANT NOTES
Do not operate fountain and lights until
fountain installation has been completed
and lights are fully submerged.
Operating light(s) out of water will result
in damage to bulb(s) and lens(es),
voiding manufacturer’s warranty.
Connect only 120V to light(s)
Higher voltage will result in immediate
damage or failure of bulb(s).