Renu Electronics FPEM-1210P-A0201L-V2 User manual

FPEM-1210P-A0201L-V2:12 Bi-directional type inputs, 10
PNP type transistor outputs. 2 Analog inputs (16-bit
resolution) & 1 Analog output (12-bit resolution)
For more information, please refer user manual which
will be available in FlexiSoft software help and/or you
can download from REPL website.
Dimension Details:
Power Supply
Voltage Rating
24VDC (±15%), 12V from base
Power Rating
Input/channel: 24VDC, 5mA typical
Output/Channel: 250mA @ 24VDC
Isolation
Optical Isolation for all I/O points. High
isolation voltage (BV= Greater than
1.5kV)
Local I/O Specification
Number of Inputs
12 Inputs Bi-directional Type
ON Voltage
Min.: 15VDC, Max.: 30VDC
OFF Voltage
Min.: -3VDC, Max.: 3VDC
Nominal Input Voltage
24VDC
Nominal Input Current
5mA typical
Input Response Time
ON: 10msec, OFF: 10msec
Input Impedance
Greater than 4.8kΩ
High Speed Inputs
2 pairs, X0-X1, X2-X3
Max. I/P frequency
200kHz
Max. Input count
42949672965
Number of Outputs
10 PNP type transistor outputs
Nominal Output Voltage
24VDC
Nominal Output Current
250mA type/channel
Output Response Time
ON/OFF: 20 to 30 µs
High Speed Outputs
2, Y0 and Y1
Max. O/P frequency
1kHz
Frequency step
1Hz
PWM duty cycle
0 to 100%
Duty cycle step
1%
Analog I/O Specification
Analog Input Total Channels
2 Input channels (16 bit resolution)
Input Type
0-20mA, 4-20mA & 0-10VDC, 0-5VDC
Analog Output Total Channels
1 Output channels (12 bit resolution)
Output type
0-20mA, 4-20mA and 0-10VDC, 0-5VDC
Accuracy
± 0.2% of full scale @ 25°C & ± 0.5% of
full scale over temperature range
Note:
In the Flexisoft select FPEM-1210P-A0201L or V2 for FPEM-1210P-
A0201L-V2 unit.
QUICK START GUIDE
FPEM-1210P-A0201L-V2
Environment & Approvals
Operating Temperature**
0 to 60°C
Storage Temperature
-20 to 85°C
Humidity
10 to 90% (Non-Condensing)
Product Dimensions
48mm x 108mm x 35.7mm (W x H x D)
Approvals
CE, UL
**Operating temperature: For UL 0 to 50°C
Mounting with base models:
With the expansions, while unpacking the unit, user will
find two screws already attached with base bottom case.
Fix the expansion with the HMI as shown below with
these screws. Fix the Expansion connector with the
expansion female connector given on base HMI.
Apply torque 0.1Nm while fixing with base unit.
Mounting with 4.3” base model:
Mounting with 7” and 10.1” base model:
For 7” and 10.1” HMI models, the procedure of mounting
expansions is same. Only instead of horizontal mounting,
expansions will mount in vertical directions.
Hence, accordingly these bases are having facility to add
3 and 5 expansions at a time respectively.
Mounting with 7” base model:
Mounting with 10.1” base model:
[Note: All Pictures shown are for illustration purpose
only. Actual product size may vary.]
SPECIFICATIONS
SPECIFICATIONS

Digital Inputs
Digital Output
HSC-Single Phase
Counter*
HSC-Quadrature
Note: *[X1 & X3 are direction pins
X1 & X3 ON means UP Count Mode
X1 & X3 OFF means Down Count Mode]
Analog Input Voltage
Analog Output Voltage
WIRING DIGRAM
Analog Input Current
Analog Output Current
DATA FORMAT
Channel Type Selection Values Table
Use the following values in the Input and output channel type. Select
register to configure the corresponding channel to particular type.
Input Channel Type
Value
Voltage: 0 to 10V
1
Voltage: 0 to 5V
6
Current: 4 to 20mA
2
Current: 0 to 20mA
3
Output Channel Type
Value
Voltage: 0 to 5V
1
Voltage: 0 to 10V
2
Current: 4 to 20mA
5
Current: 0 to 20mA
6
Configuration Registers for Analog Input
CH No.
Configuration
Register
Input
Register
Input Error
Register
Temp /
Linear
CH-0
MW0160
XW0111
MW0169
Linear
CH-1
MW0161
XW0113
MW0169
Linear
Configuration Registers for Analog Output
CH No.
Configuration
Register
Current
Register
Voltage
Register
CH-0
MW0168
YW0102
YW0101
Data Output Format for Analog Input
For, Voltage Input (0 to 10V) Voltage Input (0 to 5V)
Voltage input
Count
Voltage input
Count
0
0
0
0
5V
32767
2.5V
32767
10V
65535
5V
65535
For, Current Input (0 to 20mA) Current Input (4 to 20mA)
Current input
Count
Current input
Count
0
0
4mA
0
10mA
32767
12mA
32767
20mA
65535
20mA
65535
Data Output Format for Analog Output
V(0 to 10V) V(0 to 5V)
Voltage Output
Count
Voltage Output
Count
0
0
0
0
5V
2048
2.5V
2048
10V
4095
5V
4095
I(4 to 20mA) I(0 to 20mA)
Current Output
Count
Current Output
Count
4mA
0
0
0
12mA
2057
10mA
2048
20mA
4095
20mA
4095
Technical Support:
For Technical support, please contact factory along with the
unit serial number and revision number written on the unit
label.
Also, provide information of the application used. If possible,
e-mail the application to factory.
Rev.
Description
Date
1.0
Initial Release
18/10/2022
1.1
HSC-PTO Details added
03/01/2024
RENU Electronics Pvt. Ltd®reserves the right to change or
discontinue specifications and features without prior notice.
To view the latest and updated datasheets/manuals please visit
www.renuelectronics.com.
REVISION HISTORY