Renu Electronics FPEM-1614RP-V2 User manual

FPEM-1614RP-V2:16 Bi-directional type inputs, 14
Digital outputs - 2 PNP type transistor outputs and
12 Relay type outputs.
For more information, please refer user manual
which will be available in FlexiSoft software help
and/or you can download from REPL website.
Power Supply
Voltage Rating
24VDC (±15%), 12V from base
Power Rating
Input/channel: 24 VDC, 5mA typical
2A @24VDC for Relay
Output/Channel: 250mA @ 24VDC
for PNP, 2A @ 230VAC & 24VDC for
Relay
Isolation
Optical Isolation for all I/O points.
High isolation voltage (BV=
Greater than 1.5kV)
Local I/O Specification
Number of Inputs
16 Inputs Bi-directional Type
ON Voltage
Min.: 15VDC, Max.: 30VDC
OFF Voltage
Min.: -3VDC, Max.: 3VDC
Nominal Input Voltage
24VDC
Nominal Input Current
5mA typical
Input Response Time
ON: 10msec, OFF: 10msec
Input Impedance
4.8kΩ
Number of Outputs
2 PNP type transistor outputs
and 12 Relay type outputs
Nominal Output Voltage
30VDC
Nominal Output Current
250mA @ 24VDC for PNP, 2A @
230VAC & 24VDC for Relay
Output Response Time
ON: 10msec, OFF: 10msec
Note:
1. FPEM-V2 Series only compatible with FP2xxxTx-E/ FP4xxxTx-E
Series]
2. FPEM-V2 series do not support HSC-PWM output (for now).
3. Firmware is upgradable for the FPEM-V2 series. Moreover, after the
Firmware update, HSC-PWM output will support this series.
Please contact our Customer Support team for more details.
QUICK START GUIDE
FPEM-1614RP-V2
Environment & Approvals
Operating
Temperature**
0 to 60°C
Storage
Temperature
-20 to 85°C
Humidity
10 to 90% (Non-Condensing)
Product
Dimensions
48mm x 108mm x 35.7mm
(W x H x D)
Approvals
CE, UL
** Operating temperature: For UL 0 to 50°C
SPECIFICATIONS
SPECIFICATIONS
Dimension Details

Mounting with base models:
With the expansions, while unpacking the unit,
user will find two screws already attached with
base bottom case. Fix the expansion with the HMI
as shown below with these screws. Fix the
Expansion connector with the expansion female
connector given on base HMI.
Apply torque 0.1Nm while fixing with base unit.
Mounting with 4.3” base model:
Rev.
Description
Date
1.0
First Draft
18/10/2022
RENU Electronics Pvt. Ltd®reserves the right to
change or discontinue specifications and features
without prior notice.
To view the latest and updated datasheets/manuals
please visit www.renuelectronics.com.
Technical Support:
For Technical support, please contact
factory along with the unit serial number
and revision number written on the
address sticker of the unit.
Also, provide information of the
application used. Usually, including your
application also provides a lot of help. If
possible, e-mail the application to
factory.
Digital Inputs
Digital Output
WARNING
This equipment is suitable for use in Class I,
Division 2, Groups A, B, C and D or non-
hazardous locations only.
WARNING –EXPLOSION HAZARD –Do
not disconnect equipment unless power has
been removed or the area is known to be
non- hazardous.
WARNING –EXPLOSION HAZARD -
Substitution of components may impair
suitability for Class I, Division 2.
The list of materials used in the construction
of these devices with name of sealed
device - generic name of the material and
the supplier's name and type designation.
It is recommended that the user periodically
inspect the sealed devices used, for any
degradation of properties and Replace the
device ifany degradation is found.
WIRING DIGRAM
REVISION HISTORY
Mounting with 7” and 10.1” base model:
For 7” and 10.1” HMI models, the procedure of
mounting expansions is same. Only instead of
horizontal mounting, expansions will mount in
vertical directions.
Hence, accordingly these bases are having
facility to add 3 and 5 expansions at a time
respectively.
Examples are shown here.
Mounting with 7” base model:
Mounting with 10.1” base model:
[Note: All Pictures shown are for illustration purpose only.
Actual product size may vary.