RESORT EXTRUSIONS BIG SKY TOWER 60D User manual

PRODUCT DESCRIPTION
The Big Sky Tower is part of the Resort Extrusion family—aluminum
frames for Silicone-Edge Graphics (SEG). Custom-made on the
premises, Big Sky Tower comes in varied sizes. Big Sky Tower
accepts four individual custom fabric graphics, excluding top and
bottom. Insert graphics after frame is constructed by tilting it on its
side. Transversely, push corners of graphic into the frame’s recessed
groove. Then, starting midway on the frame going toward the corners,
continue pushing in the straight edges of the graphic. Repeat three
times. Backlit option is available.
DISPLAY DIMENSION 6 L x 6 W x 16 H
GRAPHIC DIMENSIONS 72 W x 192 H
GRAPHIC MATERIAL
UV Backlit Fabric
GRAPHIC FINISHING
Silicone beading is sewn around the perimeter of the fabric
graphic. Silicone beading is hidden from view once installed.
DISPLAY CONSTRUCTION
Aluminum Extrusion Frame
LADDER LIGHTS SPECIFICATION
EACH LIGHT BEAD .068-.43W
ANGLE 120°
OPERATING VOLTAGE 12V
TOTAL WATTAGE 350-600W MAX
TOTAL AMPERAGE 29A MAX
TRANSFORMER SPECIFICATION
OUTPUT 12V/29A
INPUT 100-120VAC/7.0A
200-240VAC/4.0A
50/60Hz
SHIPPING WEIGHTS & DIMENSIONS
Shipping Weight 124 lbs (frame only)
132 lbs (with graphics)
Shipping Dimensions 48 H x 18 W x 11.5 D
GRAPHIC TURN AROUND TIME
2 business days after proof approval
AVAILABILITY CA
BIG SKY TOWER 60D  6FT X 16FT BACKLIT
PRODUCT CODE: BIGSKYT60D6X16-LLFRM
RESORT EXTRUSIONS
On frame On graphic
Top View

PARTS LIST
Qty 23 - Split Connectors
Qty 10 - Support Struts
Qty 16 - 40CG Horizontal Extrusions
Qty 1 - Power Cord
Qty 1 - La Caja Hard Case
With Wheels
Qty 1 - Torx Key Qty 4 - Eye Hooks
Qty 2 - Ladder Lights Qty 1 - Ladder Light Wires
Qty 1 - Transformer
Qty 16 - 60D Vertical Extrusions
BIG SKY TOWER 60D  6FT X 16FT BACKLIT
PRODUCT CODE: BIGSKYT60D6X16-LLFRM
RESORT EXTRUSIONS

3. Locate the Bottom and Side Extrusions:
4. Locate the Top and Side Extrusions:
1. Attach Split Connectors to Side Extrusions:
a. Remove the screw and insert split connector
into one end of the extrusion. Match like colored
numbers together. (e.g. 3-3, 4-4).
b. Tighten screw to lock it into place. Remove
the remaining screw from the connector.
c. Then slide the other extrusion onto split
connector. Make sure extrusions are ush
and tighten the screw to secure connection.
c. Connect horizontal extrusion to
the bottom of a vertical extrusion,
screw facing inward.
d. Connect bottom extrusions to-
gether and use torx key to tighten.
a. See colored numbers on each
extrusion piece. Match like colored
numbers together. (e.g. 3-3, 4-4).
a. See colored numbers on each
extrusion piece. Match like colored
numbers together. (e.g. 3-3, 4-4).
b. End Lock is already attached to
opposite ends of extrusion.
c. Connect horizontal extrusion
to the top of a vertical extrusion,
screw facing inward.
d. Connect the top extrusions to-
gether and use torx key to tighten.
b. End Lock is already attached to
opposite ends of extrusion.
SET UP INSTRUCTIONS 1/2
2. Attach Split Connectors to Bottom & Top Horizontal Extrusions:
a. Split Connector: Remove the screw
and insert split connector into one end
of the extrusion.
b. Tighten screw to lock it into place. Remove
the remaining screw from the connector.
c. Then slide the other extrusion onto split
connector. Make sure extrusions are ush
and tighten the screw to secure connection.
BIG SKY TOWER 60D  6FT X 16FT BACKLIT
PRODUCT CODE: BIGSKYT60D6X16-LLFRM
RESORT EXTRUSIONS

8. Hook Ladder Lights:
a. Place extrusion with the light hooks on
top of the extrusion and connect together.
c. The transformer comes pre-wired. Connect
the wiring from transformer to the 2 plugs at
the bottom of the ladder lights.
b. Hang ladder LED lights on hooks and
drape them down inside the wire.
7. Attach Light Hooks:
a. Eye Hooks: Insert light hooks into the
groove in one end of the extrusion.
b. Slide the light hooks into the groove and
place them in the center. Tighten Hook.
c. Make sure light hooks are place far
apart for hooking the LED Ladder Lights.
SET UP INSTRUCTIONS 2/2
a. End Lock is already attached to opposite
ends of Support Strut.
b. Align Support Struts within marked
lines, and insert End Lock into top and
bottom grooves of frame.
c. Add a second support strut to align
marked lines and tighten screws with torx
key to secure connection.
6. Attach Support Strut to Frame:
b. Insert Center Connector and align holes
with holes on extrusion.
a. Remove screws from Center Connector. c. Repeat to connect other extrusion to make
one long piece.
5. Build Support Struts:
BIG SKY TOWER 60D  6FT X 16FT BACKLIT
PRODUCT CODE: BIGSKYT60D6X16-LLFRM
RESORT EXTRUSIONS