Vivo MOUNT-KB03B User manual

Under Desk Keyboard Tray
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-kb03b
SKU: MOUNT-KB03B/W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x1)
Mount
B(x1)
Wrist Pad
C (x1)
Tray
S-A (x6)
M5x15mm Screw
S-E (x2)
Bumper
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualied technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specied in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
STEP 1
Place Mount (A) upside down and loosen
the lever on the side. Raise and slide Arm
(A1) out from Track (A2).
4.4 lbs
(2 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-D (x2)
M4x12mm Screw
S-B (x6)
Washer
S-C (x8)
M5x12mm Screw
A
D (x1)
Connecting Plate
S-F (x4)
M5x16mm Screw
A1
A2

3
STEP 2
Hold Track (A2) against the underside of the desk with the open end of the track facing forward and
mark drilling locations with a pencil. Drill 3/8” (10mm) deep pilot holes using a 1/8” (or 3mm) drill bit,
then mount Track (A2) to the desk using M5x15mm Screws (S-A) and Washers (S-B) with a Phillips
screwdriver.
STEP 3
Assemble Tray (C) using Connecting Plate (D) and M5x12mm Screws (S-C) with a Phillips screwdriver.
Connect Arm (A2) to the tray assembly using M5x16mm Screws (S-F) and a Phillips screwdriver. Slide
Arm (A1) into Track (A2).
STEP 4
Swivel Mount (A) sideways, then install M4x12mm Screws (S-D) and Bumpers (S-E) into the front
corners of the Track using a Phillips screwdriver. Swivel the Arm (A) forward, remove paper backing
from the Wrist Pad (B), then place Wrist Pad (B) on top of Tray (C) near the front edge. S-D
A2
S-A
S-B
C
D
S-C
A1
S-F
A2
A
S-D
S-E
C
B

LAST UPDATED: 11/07/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303