RGBlink VSP 168HD User manual

VSP 168HD Quick Start
VIEWSIZE THE WORLD
Support 10Gbps of transmission rate
Support HDBaseT protocols and standards
Support USB upgrade
Support custom output resolution
Max 2048×1152@60Hz/2560×816×60Hz
input/output resolution
Seamless switching between inputs
Multiple cascade for sync mapping
Support pixel to pixel synchronous mapping

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
1
CONTENT
Product Introduction...............................................................................................................................2
Packing Configuration............................................................................................................................3
Hardware Orientation..............................................................................................................................4
Front Panel.........................................................................................................................................4
Back Panel .........................................................................................................................................5
Operating Instruction..............................................................................................................................6
Content...............................................................................................................................................6
How to Do Customized Output Resolution.................................................................................7
How to Realize Single Image Switching.....................................................................................7
How to Set up the Size and Position of the Single Image..........................................................8
How to Set up the PIP.................................................................................................................8
How to Choose the Signal Source in PIP...................................................................................9
How to Set up the Size and Position of PIP...............................................................................9
How to Set up the Layout of PIP...............................................................................................10
How to Realize the Screen Size and Full Size Switching.........................................................10
How to Realize the Text Overlay setting...................................................................................11
How to Save the Parameter......................................................................................................12
How to Load the Saved Parameter...........................................................................................12
Product Application...............................................................................................................................13
Multiple mosaic and LED Display beyond normal control resolution mosaic..................................13
Contact Information...............................................................................................................................17

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
2
Product Introduction
VSP 168HD is a 4 inputs seamless switcher
and scaler. VSP 168HD supports all common
video and graphic inputs, including 1 CVBS, 1
VGA, 1 DVI, 1 SDI (Option). VSP 168HD
meets high end presentation requirement as
its qualified image quality and advanced video
processing ability, take multiple cascade
mapping for example.
VSP 168HD supports following main
functions: max output resolution up to
2048×1152 or 2560×816, quick user config
scale operation, seamless switching for the
inputs, auto input detect, multiple cascade
mapping.
In addition, VSP 168HD use fiber and
HDBaseT output interface, and connect to
LED Display via extender, which is especially
suitable for the applications that need high
quality, long distance transmission and high
resolution image. VSP 168HD supports
RS232 control and USB port upgrade. And
through embedded high quality image
processing functions, and format conversion
function, VSP 168HD provides the high
stability of working hours.
System Connection
RGBlink offers solutions to
demanding technical problems.
Any application questions, or
required further information,
please contact with our
customer Support Engineers.
VSP 168HD System Connection Diagram

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
3
Packing Configuration
Note: SDI cable is only for VSP 168SHD.
Chinese Standard,American Standard or European Standard power line is option.
Power Line
USB Cable
SDI Cable
DB9 to RJ11
Cable
RCA to BNC
Cable
DVI 转HDMI 线
SFP Module
DVD Disk
防静电袋
Certification
DVI to HDMI
Cable
Antistatic Bag
Quick Start

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
4
Hardware Orientation
Front Panel
Button Instruction
CV
CVBS signal source button
SPLIT
Split button
HDMI
HDMI signal source button
COM
Cascade button
SDI
SDI signal source button
SAVE
Save button
VGA
VGA signal source button
LOAD
Load button
YPbPr
YPbPr signal source button
0~9
Number button, use for scale and
custom setting
BLACK
Black button
LCD Panel
Show operation menu items
MENU
Menu button
Knob
Confirm and adjust LCD menu
SCALE
Scale button

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
5
Back Panel
Input Interface
3
3G SDI input BNC port
4
SDI Loop Out BNC port
8
CVBS Input BNC port
9
VGA Input DSUB15 port
10
HDMI Input HDMI-A port
11
HDMI Loop Out HDMI-Aport
Other Interface
1
RS232 Interface
2
USB Interface USB-B port
14
Power IEC-3
Output Interface
5
Fiber Output LC port
6
SDI Output BNC port
7
HDBaseT Output RJ45 port
12
DVI Output DVI-I port
13
DVI+VGADVI-I Output

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
6
Operating Instruction
Content
How to Do Customized Output Resolution
How to Realize Single Image Switching
How to Set up the Size and Position of Signal Image
How to Set up the PIP
How to Choose the Signal Source in PIP
How to Set up the Size and Position of PIP
How to Set up the Layout of PIP
How to Realize Screen Size and Full Size Switching
How to Realize the Text Overlay setting
How to Save the Parameter
How to Load the Saved Parameter

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
7
How to Do Customized Output Resolution
1. Push [MENU] button to enter the menu items, turn knob and go to [OUTPUT FORMAT], push knob
and confirm to go into the [OUTPUT FORMAT] menu.
2. Push knob and go into [CUSTOMIZED] menu.
3. Turn knob on each bit position, and change the value of the bit by the digital buttons on the front
panel.
4. After the digital push knob will add ×, means before ×is the horizontal size. Same operation for
vertical size.
5. After the digital push knob will add @, means before @ is the vertical size. Same operation by push
digital buttons to set the refresh rate.
6. After input all the values, push knob to enable VSP 168HD to output this resolution. VSP 168HD will
take 5 to 10 seconds to enable this output resolution.
How to Realize Single Image Switching
1. Boot the system default CV1 to the current input source (key lights and flashes), if need seamless
switching other source such as VGA, push VGA button.
2. Choose VGA buttons, button CV1 light is off, and VGA button lights and flashes, it can realize single
picture of input signal source switching (switch CV1 to VGA).The same method can switched HDMI
and SDI.
Note: Seamless switch: means signal switch will not appear any flash point, black, shaking or delay.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
8
How to Set up the Size and Position of the Single Image
1. Push MENU button to enter the menu items.
2. Rotate the knob, choose [OUTPUT].
3. Push the knob to confirm, rotate the knob again, choose [SCALE].
4. Push the knob to confirm, and enter [SCALE] option, rotate the knob to choose the corresponding
parameters and set to default values, (the default value can also be set via the number button), after
setting, push the knob to confirm.
5. If the operation is wrong, or need to factory resetting, user can enter the [SCALE] option and choose
“RESET” to recover factory reset.
How to Set up the PIP
1. Push MENU button to enter the menu items.
2. Rotate the knob and choose [OUTPUT].
3. Push the knob to confirm, rotate the knob again, choose [PIP].
4. Push the knob to confirm, rotate the knob, choose ON and confirm, then start PIP mode.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
9
How to Choose the Signal Source in PIP
1. Push MENU button to enter the menu items.
2. Rotate the knob, choose [OUTPUT].
3. Push the knob to confirm, rotate the knob again, choose [PIP].
4. Push the knob to confirm, rotate the knob again, choose [SELECT], choose IMAGE Aas main image.
5. Push CV, VGA, HDMI, SDI as the input signal of Image A.
6. The same steps, select the IMAGE B as sub-image, push CV, VGA, HDMI, SDI as the input signal
Image B.
7. With above steps, can complete the choice of signal source in PIP.
How to Set up the Size and Position of PIP
1. Push MENU button to enter the menu items. Rotate the knob, choose [OUTPUT].
2. Push the knob to confirm, rotate the knob again, choose [PIP].
3. Push the knob to confirm, rotate the knob again, choose [SELECT], choose IMAGEAas main image.
4. Push MENU button, rotate the knob, choose [OUTPUT], enter and choose [SCALE]. User can set the
size and position of IMAGEA according to actual need.
5. After setting, with the same steps, choose IMAGE B as the sub-image, and the setting is the same
with IMAGE A.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
10
How to Set up the Layout of PIP
1. In PIP mode, for details, please refer to: How to Set up the PIP.
2. Rotate the knob, choose [LAYOUT], push the knob to confirm.
3. Rotate the knob again, choose three PIP layout modes, shown as below:
PIP L+T PBP L+R PBP T+B
How to Realize the Screen Size and Full Size Switching
1. Push MENU button, rotate the knob, choose [OUTPUT], enter and choose [SCREEN].
2. Set the size and position of the screen according to actual need.
3. When screen setup is completed, choose SCREEN SIZE or FULL SIZE in [MODE] in [SCREEN]
option to realize the screen size and full size switching.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
11
How to Realize the Text Overlay setting
1. Push MENU button, rotate the knob, choose [OUTPUT].
2. Rotate the knob, choose [TEXT OVERLAY] and enter [TEXT OVERLAY], push the knob to confirm.
3. Rotate the knob, choose [TEXT OVERLAY] mode, choose ON to start TEXT OVERLAY function.
4. Push MENU, return to [TEXT OVERLAY], rotate the knob, LCD screen displays menu options, select
13 modes in PRESET, or select BLEND, which includes two modes:
Mode 1: Graphic content locate at the top and is non-transparent, background transparency is
controlled by double-picture transparency.
Mode 2: Graphic content is controlled by double-picture transparency, the background is completely
transparent.
Rotate the knob and choose the mode.
5. Push MENU, return to [TEXT OVERLAY], rotate the knob, chooseABOVE/BELOW to select the
layer position for IMAGE B.
6. Push MENU, return to [TEXT OVERLAY], rotate the knob, choose BLEND LEVEL, and set the image
display transparency, regulating range between 0~16.
7. Push MENU, return to [TEXT OVERLAY], rotate the knob, choose the color value:
RED: The value range of color RED that to be set, regulating range between 0~255.
GREEN: The value range of color GREEN that to be set, regulating range between 0~255.
BLUE: The value range of color BLUE that to be set, regulating range between 0~255.
8.At the same time, user can view the effect through the screen, to get a better setting.
Note: All the above settings are available only for IMAGE B.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
12
How to Save the Parameter
1. VSP 168HD provides 10 save modes.After setting, push SAVE button to start save function.
2. Rotate the knob, select the location that need to save, for example, save to SAVE2, choose SAVE2,
push the confirm, and save the parameter finished.
Note: The operation is same as MENU SAVE SETUP SAVE TO.
How to Load the Saved Parameter
1. VSP 168HD provides 10 load modes. Push LOAD button to start the LOAD function.
2. Rotate the knob, select the location that need to load, for example, load from SAVE1, choose SAVE1
and confirm, and load the parameter finished.
Note: The operation is same as MENU SAVE SETUP LOAD FROM.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
13
Product Application
Multiple mosaic and LED Display beyond normal
control resolution mosaic
Project 1: Set VSP 168HD/1# as PIP mode, and divides signal to VSP 168HD/2# to VSP 168HD/5# for
cascade by using DVI matrix (DXP D0404). The split modes, including “FIELD GLYPH”, “HORIZONTAL
1/4”, “VERTICAL 1/4” and “IRREGULAR” can be achieved.
Project 2: VSP 168HD/1# divides signal to VSP 168HD/2# to VSP 168HD/5# for cascade by using DVI
matrix (DXP D0404).

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
14
Project 1: Format conversion the front-end signal source with VSP 168HD/1# , connect DVI output
interface to the HDMI input interface of VSP 168HD/2#, and output to the next VSP 168HD by HDMI
loop. The same method, connect the other VSP 168HD for cascade. The quantity of VSP 168HD
depends on the size of LED display.
Project 2: Format conversion the front-end signal source with VSP 168HD/1# , and set PIP mode,
output to the HDMI input interface of VSP 168HD/2#, then output to the next VSP 168HD by HDMI loop.
The same method, connect the other VSP 168HD for PIP cascade. The quantity of VSP 168HD
depends on the size of LED display.
Here we use 4 sets of VSP 168HD for cascade, the split modes includes “FIELD GLYPH”,
“HORIZONTAL 1/4”, “VERTICAL 1/4” and “IRREGULAR”.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
15
Project Description: The project is divide VSP 168HD/1# signal to VSP 168HD/2# to VSP 168HD/17#
for cascade by using DVI matrix (DXP D1616), and then output to LED display. This project can achieve
super resolution cascade and custom resolution cascade, also can switch among different signals.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
16
VSP 168HD can also cascade through the upper computer.
Connect the USB interface of VSP 168HD to USB hub, then connect USB hub to the upper computer,
and open the split function for cascade through computer.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [email protected] http://www.rgblink.cn
17
Contact Information
Warranty:
All video products are designed and tested to the highest quality standard and backed by
a full 3-year parts and labor warranty. Warranties are effective upon delivery date to
customer and are non-transferable. RGBlink warranties are only valid to the original
purchase/owner. Warranty related repairs include parts and labor, but do not include
faults resulting from user negligence, special modification, lighting strikes,
abuse(drop/crush), and/or other unusual damages.
The customer shall pay shipping charges when unit is returned for repair.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone
Xiamen, Fujian Province, P.R.C
●Tel: [phone]
●Fax: [phone]
●Customer Hotline：[phone]
●Web:
~ http://www.rgblink.com
~ http://www.rgblink.cn
●E-mail: rgbl[email protected]