Rheem Classic Plus 05EAUER User manual

FORM NO. G11-491 REV. 1
Supersedes Form No. G11-491
GAS FURNACES
SUPER QUIET 80™
(A.F.U.E.✝)TWO STAGE
DOWNFLOW
GAS FURNACES
The Rheem Classic®Plus Super Quiet 80™2-Stage line of
downflow gas furnaces is designed for installation in clos-
ets, alcoves, utility rooms, or attics. The design is certified
by CSA International.
Features
■Patented heat exchanger, constructed of both stainless
and aluminized steel for the maximum in corrosion
resistance.
■Low profile “34 inch” [864 mm] design is lighter and easier
to handle, and leaves room for optional equipment.
■Left or right side gas and electric inlet connections with
quick, simple change.
■Direct spark ignition.
■Integrated control board with humidifier and electronic air
cleaner hookups.
■Insulated blower compartment, a two stage gas valve and
a specially designed two speed draft inducer motor make
it one of the quietest furnaces on the market today.
■Pre-paint galvanized steel cabinet.
■Grab-holes in doors to aid in easy door removal and
replacement.
■Compatible with single or two-stage thermostat. (For opti-
mal performance, two-stage thermostat recommended.)
A variety of cooling coils and plenums designed to use with
Rheem Classic®Plus Super Quiet 80™2-Stage gas fur-
naces are available as optional accessories.
✝A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with Department
of Energy test procedures.
RGLQ- SERIES
Models with Input Rates from
50,000 to 150,000 BTU/HR
[15 to 44 kW]
(U.S. & Canadian Models)
Annual Fuel Utilization Efficiency - AFUE
THIS MODEL
ENER UIDE
97%78%
HIGH
MID
82% 88%
80.0%

2 Rheem Heating, Cooling and Water Heating
STANDARD EQUIPMENT
Completely assembled and wired; 2 speed induced draft blower; high and low
pressure switches; 2 stage redundant main gas control; blower compartment
door safety switch; solid state time on/time off blower control; limit control;
transformer; direct drive multi-speed blower motor. Furnaces are equipped
with cooling/heating relay and transformer (40VA) ready for air conditioning
applications. (Please note: a thermostat is not included as standard equipment.)
Flame sensor diagnostics; fused-protection (secondary).
NOTE: Furnace is not listed for use with fuels other than natural or L.P.
(propane) gas.
The complete terms of limited and other warranties are available at our
sales office, or through local installer.
All models can be converted by a qualified Rheem professional or local service
dealer to use L.P. (propane) gas without changing burners. Factory approved
kits must be used to convert from natural to L.P. (propane) gas and may be
ordered as optional accessories.
For L.P. (propane) operation, refer to Conversion Kit Index Form.
NOTE: For natural and L.P. (propane) gas models, direct spark ignition is 100%
lockout type.
WARNING
THIS FURNACE IS NOT APPROVED
OR RECOMMENDED
FOR USE IN MOBILE HOMES
Integrated
Furnace Control
Heat Exchanger
In-Shot Burners
Direct Spark Ignitor
CLASSIC®PLUS SUPER QUIET 80 ™
TWO STAGE
DOWNFLOW GAS FURNACE
Remote Sensor
Two-Speed Draft
Inducer Motor

Rheem Heating, Cooling and Water Heating 3
BEFORE PURCHASING THIS APPLIANCE, READ IMPORTANT ENERGY COST AND EFFICIENCY INFORMATION AVAILABLE
FROM YOUR RETAILER.
PHYSICAL DATA AND SPECIFICATIONS
U.S. AND CANADA MODELS (DOWNFLOW)
MODEL IDENTIFICATION—DOWNFLOW MODELS
RG L Q
—07E A M E R
Rheem Gas Downflow Design Heating Input Designation Variations Blower Heating & Cooling Fuel Type
U= 11 x 6
[279 x 152 mm]
M= 11 x 7
[279 x 178 mm]
R= 11 x 10
[279 x 254 mm]
E= 1100-1330 CFM
[519-628 L/s]
J= 1800-2075 CFM
[850-979 L/s]
Furnace Series
Electric
Ignition
05E
07E
10E
12E
15E
A= Std.
Cabinet
B= Wide
Cabinet
Designation Designation R= Natural Gas,
U.S. and
Canadian
Standard
Furnace
Electric
Ignition–
NOxModels
05N
07N
10N
12N
15N
Input
BTU/HR
50,000 [15 kW]
75,000 [22 kW]
100,000 [29 kW]
125,000 [37 kW]
150,000 [44 kW]
[ ] Designates Metric Conversions
MODEL NUMBERS
RGLQ- SERIES
05EAUER
05NAUER
07EAMER
07NAMER
Standard Filter–In.
[mm]
(1) 14 x 20
[356 x 508]
(2) 12 x 20
[306 x 508]
High Input–BTU–BTU/Hr [kW] ➁50,000 [15] 75,000 [22]
Heating Capacity–BTU/Hr [kW] ➀40,360 [12] 61,020 [18]
Blower (D x W) [mm] 11 x 6
[279 x 152]
11 x 7
[279 x 178]
Motor H.P.–[W]
Speeds–Type
1/2[373]
4-PSC
1/2[373]
4-PSC
Motor Full Load Amps 6.8 7.1
Heating Speed–High Fire MED-LOW MED-HIGH
Cooling Speed HIGH HIGH
Cooling CFM @ .5" [kPa] E.S.P.
(Nominal) [L/s]
1200
[566]
1200
[566]
Max. E.S.P. (In. W.C.) [kPa] 0.5 [.12] 0.5 [.12]
Temperature Rise Range °F [°C]
High Input
25-55
[13.9-30.6]
35-65
[19.4-36.1]
Max. Outlet Air Temp. °F
[°C]
155
[68.3]
165
[78.3]
Approx. Shipping Weight (Lbs.)
[kg]
85
[39]
105
[48]
AFUE ➀80.0% 80.0%
Low Input–BTU/Hr [kW] 35,000 [10] 52,500 [15]
Heating Capacity–BTU/Hr [kW] 28,000 [8] 41,600 [12]
10EAMER
10NAMER
10EBRJR
10NBRJR
12EARJR
12NARJR
(2) 12 x 20
[306 x 508]
(2) 14 x 20
[356 x 508]
(2) 14 x 20
[356 x 508]
100,000 [29] 100,000 [29] 125,000 [37]
70,000 [20] 70,000 [20] 87,500 [25]
81,600 [24] 81,040 [24] 101,750 [29]
56,000 [16] 56,000 [16] 70,000 [20]
11 x 7
[279 x 178]
11 x 10
[279 x 254]
11 x 10
[279 x 254]
1/2[373]
4-PSC
3/4[559]
4-PSC
3/4[559]
4-PSC
7.1 9.5 9.5
MED-HIGH MED-HIGH MED-HIGH
HIGH HIGH HIGH
1200
[566]
2000
[944]
2000
[944]
0.5 [.12] 0.5 [.12] 0.5 [.12]
45-75
[25.0-41.7]
30-60
[16.7-33.3]
35-65
[19.4-36.1]
180
[82.2]
180
[82.2]
180
[82.2]
115
[52]
120
[54]
140
[63]
80.0% 80.0% 80.0%
15EARJR
15NARJR
(2) 14 x 20
[356 x 508]
150,000 [44]
105,000 [30]
121,550 [35]
84,000 [24]
11 x 10
[279 x 254]
3/4[559]
4-PSC
9.5
MED-HIGH
HIGH
2000
[944]
0.5 [.12]
50-80
[27.8-44.4]
190
[87.7]
150
[68]
80.0%
Heating–Ext. Static Pressure [kPa] .10 [.025] .12 [.029] .15 [.037] .15 [.037] .20 [.05] .20 [.05]
Heating Speed–Low Fire LOW MED-LOW LOW LOW LOW LOW
Temperature Rise Range °F [°C]
Low Input
20-50
[11.1-27.8]
30-60
[16.7-33.0]
20-50
[11.1-27.8]
35-65
[19.4-36.1]
25-55
[13.9-30.6]
30-60
[16.7-33.3]
NOTES: All models are 115V, 60HZ, 1
Ø . Gas connection size for all models is 1/2" [12.7 mm] N.P.T.
➀In accordance with D.O.E. test procedures.
➁ See Conversion Kit Index for high altitude derate in U.S. applications. For Canadian applications, reference the furnace installation instructions.

4 Rheem Heating, Cooling and Water Heating
NOTES: ➀May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.
➁ May be 0" [0 mm] with type B vent.
➂May be 1" [25 mm] with type B vent.
Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with
local codes.
[ ] Designates Metric Conversions
DOWNFLOW DIMENSIONS
DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]
MODEL
RGLQ- A B C D E
REDUCED CLEARANCES (IN.) [mm]
05 14 [356] 1227/32 [326] 103/8[264] ➀131/8[333] 04 [102] ➁01 [25] 3 [76] 6 [152] ➂
LEFT
SIDE
RIGHT
SIDE BACK TOP FRONT VENT SHIP. WGTS. (LBS.) [kg]
85 [38.6]
07 171/2[445] 1611/32 [415] 121/8[308] ➀165/8[422] 03 [76] ➁01 [25] 3 [76] 6 [152] ➂105 [47.6]
10 (A) 171/2[445] 1611/32 [415] 121/8[308] ➀165/8[422] 03 [76] ➁01 [25] 3 [76] 6 [152] ➂115 [52.2]
10 (B) 21 [533] 1927/32 [504] 137/8[352] ➀201/8[511] 0001 [25] 3 [76] 6 [152] ➂120 [54.4]
12 241/2[622] 2311/32 [593] 155/8[397] ➀235/8[600] 0 0 0 1 [25] 3 [76] 6 [152] ➂140 [63.5]
15 241/2[622] 2311/32 [593] 155/8[397] ➀235/8[600] 0 0 0 1 [25] 3 [76] 6 [152] ➂150 [68]

Rheem Heating, Cooling and Water Heating 5
MODEL
NUMBER
RGLQ-
SERIES
BLOWER
SIZE
[mm]
MOTOR
H.P.
[W]
BLOWER
SPEED
CFM [L/s] AIR DELIVERY
EXTERNAL STATIC PRESSURE INCHES [kPa] WATER COLUMN
.1 [.02] .2 [.05] .3 [.07] .4 [.10] .5 [.12] .6 [.15] .7 [.17]
05*AUER 11 x 6
[279 x 152]
1/2
[373]
LOW
MED-LO
MED-HI
HIGH
655 [309]
975 [460]
180 [557]
1335 [630]
630 [297]
943 [445]
1140 [538]
1290 [608]
600 [283]
915 [432]
1105 [521]
1250 [590]
565 [266]
886 [418]
1067 [503]
1202 [567]
532 [251]
852 [402]
1027 [484]
1157 [546]
500 [236]
813 [383]
980 [462]
1110 [524]
467 [220]
770 [363]
924 [436]
1060 [500]
07*AMER 11 x 7
[279 x 178]
1/2
[373]
LOW ➀
MED-LO
MED-HI
HIGH
910 [429]
1074 [507]
1229 [580]
1409 [665]
887 [418]
1054 [497]
1207 [569]
1385 [653]
863 [407]
1034 [488]
1184 [558]
1361 [642]
839 [396]
1007 [475]
1159 [547]
1329 [627]
814 [384]
979 [462]
1134 [535]
1297 [612]
776 [366]
944 [455]
1099 [518]
1260 [594]
738 [348]
908 [428]
1063 [501]
1223 [577]
10*BRJR 11 x 10
[279 x 254]
3/4
[559]
LOW
MED-LO
MED-HI
HIGH
1374 [648]
1709 [806]
2132 [1006]
2362 [1114]
1356 [640]
1686 [795]
2085 [984]
2300 [1085]
1339 [632]
1663 [784]
2038 [961]
2237 [1055]
1323 [624]
1635 [771]
1988 [938]
2173 [1025]
1286 [607]
1607 [758]
1937 [914]
2108 [994]
1249 [589]
1562 [737]
1882 [888]
2036 [960]
LOW 895 [422] 874 [412] 852 [402] 825 [389] 798 [376] 766 [362] 734 [346]
1212 [572]
1516 [715]
1827 [862]
1964 [926]
15*ARJR 11 x 10
[279 x 254]
3/4
[559]
LOW
MED-LO
MED-HI
HIGH
1300 [614]
1675 [791]
2105 [993]
—
1280 [604]
1650 [779]
2075 [979]
2340 [1104]
1230 [580]
1620 [765]
2035 [960]
2290 [1081]
1205 [569]
1570 [741]
1990 [939]
2215 [1045]
1170 [552]
1545 [729]
1955 [923]
2145 [1012]
1115 [526]
1485 [701]
1900 [897]
2080 [982]
12*ARJR 11 x 10
[279 x 254]
3/4
[559]
LOW
MED-LO
MED-HI
HIGH
1315 [620]
1618 [763]
2065 [974]
2275 [1074]
1292 [609]
1597 [753]
2025 [956]
2219 [1047]
1269 [599]
1576 [743]
1984 [936]
2163 [1021]
1250 [590]
1552 [732]
1938 [915]
2103 [992]
1231 [581]
1528 [721]
1891 [892]
2042 [964]
1194 [563]
1486 [701]
1824 [861]
1982 [935]
1157 [546]
1443 [681]
1756 [829]
1921 [907]
1030 [486]
1425 [673]
1815 [857]
1995 [942]
10*AMER 11 x 7
[279 x 178]
1/2
[373]
MED-LO
MED-HI
HIGH
1052 [496]
1238 [584]
1383 [652]
1033 [487]
1217 [574]
1366 [644]
1013 [478]
1196 [564]
1348 [636]
991 [467]
1169 [551]
1317 [621]
968 [457]
1143 [539]
1286 [607]
930 [439]
1094 [516]
1245 [587]
891 [420]
1044 [492]
1203 [567]
NOTES: ➀ Not to be used as a low stage heating speed.
Data compiled with factory filters installed.
See Form Number C11-211 for “N” Coil Data.
Factory rated to 0.5" W.C.
*E = Standard
*N = NOx Models
[ ] Designates Metric Conversions
GENERAL TERMS OF LIMITED WARRANTY
Rheem will furnish a replacement for any part of this product
which fails in normal use and service within the applicable
period stated, in accordance with the terms of the limited
warranty.
*For Complete Details of the Limited Warranty, Including Applicable
Terms and Conditions, See Your Local Installer or Contact the
Manufacturer for a Copy.
Gas Heat Exchanger Limited Warranty .........Limited Lifetime
Conditional Parts* (Registration Required) ......Ten (10) Years
BLOWER PERFORMANCE DATA—DOWNFLOW MODELS

6 Rheem Heating, Cooling and Water Heating
RXPF-F01 and F02
FOSSIL FUEL KIT—is for use with Rheem Heat Pumps and Classic
Series warm air furnaces. RXPF-F02 meets TVA requirements.
ACCESSORIES—DOWNFLOW
DOWNFLOW WARNING: Unit design is certified for installation on non-com-
bustible floor. A special factory supplied combustible floor sub-base is
required when installing on a combustible floor. Failure to install the sub-base
may result in fire, property damage and personal injury.
COMBUSTIBLE
FLOOR BASE
A
IN. [mm]
B
IN. [mm]
USE WITH
FURNACE SIZES
RXGC-B24 25 [635] 233/4[603] RGLQ-12, RGLQ-15
RXGC-B14 141/2[368] 131/4[337] RGLQ-05
RXGC-B17 18 [457] 163/4[425]RGLQ-07, RGLQ-10(-)A
RXGC-B21 211/2[546] 201/4[514]RGLQ-10(-)B
C
IN. [mm]
213/4[552]
111/4[286]
143/4[451]
181/4[464]
FOR HIGH ALTITUDES:
HIGH ALTITUDE CONVERSION:
See Installation Instructions for more high altitude information.
CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines
when converting furnaces for high altitudes.
COMBUSTIBLE FLOOR BASE DIMENSIONS
RXGF-CC*
FILTER RACK—Downflow top
return mount.
NOTE: Filter racks are shipped
without filters.
*Filters available through PROSTOCK®.
141/2[356] 45 [13.19] & 50 [14.65] 14 [356] x 20 [508] 1
171/2[445] 67 [19.64], 75 [21.98] & 100 [29.31] 12 [305] x 20 [508] 1
211/2[533] 100 [29.31] 12 [305] x 20 [508] 2
241/2[622] 125 [36.63] & 150 [44.0] 14 [356] x 20 [508] 2
DOWNFLOW FILTER SIZES
FURNACE
WIDTH
IN. [mm]
INPUT
BTUH [kW]
SIZE
IN. [mm] QUANTITY
[ ] Designates Metric Conversions

Rheem Heating, Cooling and Water Heating 7
NOTES

Before proceeding with installation, refer
to installation instructions packaged
with each model, as well as complying
with all Federal, State, Provincial, and
Local codes, regulations, and practices.
Rheem Heating,
Cooling and
Water Heating
P.O. Box 17010, Fort Smith, AR 72917
“In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.”
PRINTED IN U.S.A. 10-09 DC FORM NO. G11-491 REV. 1
Supersedes Form No. G11-491