Rheem RGPR 05EBMKR User manual

FORM NO. G11-489 REV. 1
Supersedes Form No. G11-489
GAS FURNACES
Annual Fuel Utilization Efficiency - AFUE
THIS MODEL
ENER UIDE
97%78%
HIGH
MID
82% 88%
80.0%
SUPER QUIET 80
TWO STAGE
UPFLOW/HORIZONTAL
GAS FURNACES
The Rheem Prestige Series®Super Quiet 80 Two Stage
line of upflow/horizontal gas furnaces are designed for util-
ity rooms, closets, alcoves, or attics. Because of the Pres-
tige’s low-profile 34 inch [864 mm] height, the upflow
model installed vertically can also be used to satisfy
most applications that traditionally call for a horizontal
furnace.
The design is certified by CSA International.
Features
■Patented Heat Exchanger, constructed of both stainless
and aluminized steel for the maximum in corrosion resis-
tance.
■Low profile “34 inch” [864 mm] design is lighter and eas-
ier to handle, and leaves room for optional equipment.
■Energy efficient and quiet ECM 2+ motor.
■Improves cooling efficiency when matched with rated
condensing unit and coil.
■Constant CFM.
■Dip switch settings for selectable cooling airflow.
■On-demand dehumidification terminal for improved com-
fort in cooling mode.
■Convertible from upflow to horizontal left or right.
■Left or right side gas and electric inlet connections.
■All models equipped with flame sensor feature, an inte-
grated board with humidifier and electronic air cleaner
hookups.
■Insulated blower compartment, a slow-open gas valve, a
specially designed draft inducer motor and blower motor
make it one of the quietest furnaces on the market today.
■Pre-paint galvanized steel cabinet.
■Molded permanent filter.
■Easy door removal and replacement.
■Compatible with single or two-stage thermostat. (For opti-
mal performance, two-stage thermostat recommended.)
A variety of cooling coils and plenums designed to use with
Rheem Prestige Series®Super Quiet 80 Two Stage gas fur-
naces are available as optional accessories.
✝A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with Department
of Energy test procedures.
RGPR- SERIES
ECM Equipped
Models with Input Rates from
50,000 to 125,000 BTU/HR
115 Volts, 60 Hz, Single Phase
[15 to 37 kW]
(U.S. & Canadian Models)

2 Rheem Manufacturing Company
Direct Spark Ignitor
Flame Sensor
In-Shot Burners
Pressure Switch
IFC
Integrated
Furnace
Control
ECM Interface
Furnace Control
Heat Exchanger
Two-Speed Draft
Inducer Motor
ECM Motor
The complete terms of limited and other warranties are available at our
sales office, or through local installer.
All models can be converted by a qualified HVAC professional or local service
dealer to use L.P. (propane) gas without changing burners. Factory approved
kits must be used to convert from natural to L.P. (propane) gas and may be
ordered as optional accessories from a Rheem parts distributor.
For L.P. (propane) operation, refer to Conversion Kit Index Form.
WARNING
THIS FURNACE IS NOT APPROVED
OR RECOMMENDED
FOR USE IN MOBILE HOMES
STANDARD EQUIPMENT
Completely assembled and wired; 2 speed draft inducer; high and low pressure
switches; redundant 2 stage main gas control; blower compartment door safety
switch; solid state time on/time off blower control; limit control; transformer;
ECM blower motor. Furnaces are equipped with cooling/heating relay and
transformer (40VA) ready for air conditioning applications. (Please note: a
thermostat is not included as standard equipment.) Flame sensor diagnostics;
fused protection (secondary).
RHEEM PRESTIGE SERIES SUPER QUIET 80
TWO STAGE
UPFLOW/HORIZONTAL GAS FURNACE

Rheem Manufacturing Company 3Rheem Manufacturing Company 3
BEFORE PURCHASING THIS APPLIANCE, READ IMPORTANT ENERGY COST AND EFFICIENCY INFORMATION AVAILABLE
FROM YOUR RETAILER.
PHYSICAL DATA AND SPECIFICATIONS (UPFLOW)
U.S. AND CANADA MODELS
GENERAL TERMS OF LIMITED WARRANTY
Rheem will furnish a replacement for any part of this product
which fails in normal use and service within the applicable
period stated, in accordance with the terms of the limited
warranty.
For Complete Details of the Limited Warranty, Including Applicable Terms
and Conditions, See Your Local Installer or Contact the Manufacturer for
a Copy.
Gas Heat Exchanger Limited Warranty ......Twenty (20) Years
*Any Other Part.............................................Five (5) Years
*This five year limited warranty is applicable only to single-phase
products installed in residential applications on or after January 1, 2001.
MODEL IDENTIFICATION—UPFLOW MODELS
[ ] Designates Metric Conversions
MODEL NUMBERS
RGPR- SERIES
05EBMKR
05NBMKR
07EAMKR
07NAMKR
10EBRMR
10NBRMR
12EARMR
12NARMR
Temperature Rise Range
°F [°C]
25-55 [13.9-30.6] 30-60 [17-33] 30-60 [17-33] 35-65 [19.4-36.1]
100% High Input–BTU/Hr [kW] ➁50,000 [15] 75,000 [22] 100,000 [29] 125,000 [37]
High Heating Capacity–BTU/Hr [kW] ➀40,000 [12] 60,000 [18] 80,000 [23] 100,000 [29]
70% Low Input–BTU/Hr [kW] 35,000 [10] 52,500 [15] 70,000 [20] 87,500 [25]
Low Heating Capacity–BTU/Hr [kW] 28,000 [8] 42,000 [12] 56,000 [16] 70,000 [20]
Heating–Ext. Static Pressure [kPa] .10 [.025] .15 [.037] .20 [.05] .20 [.05]
Blower (D x W) [mm] 11 x 7
[279 x 178]
11 x 7
[279 x 178]
11 x 10
[279 x 254]
11 x 10
[279 x 254]
ECM Motor H.P. [W] 3/4[559] 1/2[373] 1 [746] 1 [746]
Motor Full Load Amps. 9.6 7.7 12.8 12.8
Heating Speed CFM–High Fire [L/s] 850 [401] 1176 [555] 1600 [753] 1832 [865]
Heating Speed CFM–Low Fire [L/s] 625 [295] 980 [462] 1300 [615] 1420 [670]
Cooling CFM @ .5" [kPa] E.S.P.
(Nominal) [L/s]
1200
[566]
1200
[566]
2000
[944]
2000
[944]
Max. E.S.P. (In. W.C.) [kPa] 0.8 [.2] 0.8 [.2] 0.8 [.2] 0.8 [.2]
Max. Outlet Air Temp. °F [°C] 155 [68.3] 165 [73.8] 170 [76.6] 180 [82.2]
Standard Filter Size–Inches
[mm]
153/4x 25
[400 x 635]
153/4x 25
[400 x 635]
191/4x 25
[489 x 635]
223/4x 25
[578 x 635]
Return Air Cabinets
(Opt.) RXGR-
Filter Size [mm]
C17B
(2) 12 x 16
[305 x 406]
C17B
(2) 12 x 16
[305 x 406]
C21B
(2) 20 x 16
[508 x 406]
C24B
(2) 24 x 16
[610 x 406]
AFUE ➀80% 80% 80% 80%
07EBRQR
07NBRQR
25-55 [13.9-30.6]
75,000 [22]
60,000 [18]
52,500 [15]
42,000 [12]
.15 [.037]
11 x 10
[279 x 254]
3/4[559]
9.6
1305 [616]
1125 [533]
1600
[755]
0.8 [.2]
165 [73.8]
191/4x 25
[489 x 635]
C21B
(2) 20 x 16
[508 x 406]
80%
115 [52]
Approx. Shipping Weight (Lbs.) [kg] 110 [50] 115 [52] 120 [54] 140 [63]
15
Maximum Overcurrent Protection 15 15 15 15
12.0
Unit Amps 8.7 8.7 12.0 12.0
20-50 [11.1-27.8] 20-50 [11.1-27.8] 25-55 [13.9-30.6] 30-60 [17-33]20-50 [11.1-27.8]
High Input
Low Input
➀ In accordance with D.O.E. test procedures.
➁ See Conversion Kit Index Form for high altitude derate.
G P R
Furnace
A M K R
Rheem Gas Upflow/ Design Heating Input Designation
Horizontal Series
Variations Blower Heating & Cooling Fuel Type
M= 11 x 7
[279 x 178 mm]
R= 11 x 10
[279 x 254 mm]
K= 600-1200 CFM
[283-566 L/s]
M= 1200-2000 CFM
[566-944 L/s]
Q= 1000-1600 CFM
[566-944 L/s]
Electric
Ignition
05E
07E
10E
12E
A= Std.
Cabinet
B= Wide
Cabinet
Designation Designation R= Natural Gas,
U.S. and
Canadian
Standard
Furnace
Input
BTU/HR
50,000 [15 kW]
75,000 [22 kW]
100,000 [29 kW]
125,000 [37 kW]
NOx
Model
05N
07N
10N
12N
278
Option Code
for High
Altitude,
(available on
certain models)
R07E

4 Rheem Manufacturing Company
NOTES: ➀May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.
➁ May be 0" [0 mm] with type B vent.
➂May be 1" [25 mm] with type B vent.
Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with
local codes.
[ ] Designates Metric Conversions
UPFLOW DIMENSIONS
UPFLOW DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]
MODEL
RGPR- A B C D E
REDUCED CLEARANCES (IN.) [mm]
05, 07A 171/2[445] 1611/32 [415] 123/8[314] ➀151/2[381] 03 [76] ➁01 [25] 3 [76] 6 [152] ➂
LEFT
SIDE
RIGHT
SIDE BACK TOP FRONT VENT SHIP. WGTS. (LBS.) [Kg]
105 [47.6]
07B, 10 211/2[533] 1927/32 [504] 141/8[359] ➀181/2[470] 0 0 0 1 [25] 3 [76] 6 [152] ➂120 [54.4]
12 241/2[622] 2311/32 [593] 157/8[403] ➀221/2[559] 0 0 0 1 [25] 3 [76] 6 [152] ➂140 [63.5]
F
21/2[64]
21/2[64]
21/2[64]

Rheem Manufacturing Company 5
NOTES: ➀May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.
➁ May be 0" [0 mm] with type B vent.
➂May be 1" [25 mm] with type B vent.
Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with
local codes.
[ ] Designates Metric Conversions
HORIZONTAL DIMENSIONS
HORIZONTAL DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]
WARNING
THIS FURNACE IS NOT APPROVED
OR RECOMMENDED FOR INSTALLATION
ON ITS BACK, WITH ACCESS DOORS
FACING UPWARDS.
MODEL
RGPR- A B C D E
REDUCED CLEARANCES (IN.) [mm]
05, 07A 171/2[445] 1611/32 [415] 123/8[314] ➀15 [381] 03 [76] ➁01 [25] 3 [76] 6 [152] ➂
LEFT
SIDE
RIGHT
SIDE BACK TOP FRONT VENT SHIP. WGTS. (LBS.) [Kg]
07B, 10 21 [533] 1927/32 [504] 141/8[359] ➀181/2[470] 0 0 0 1 [25] 3 [76] 6 [152] ➂120 [54.4]
110 [49.9]
12 241/2[622] 2311/32 [593] 157/8[403] ➀22 [559] 0 0 0 1 [25] 3 [76] 6 [152] ➂140 [63.5]
F
21/2[64]
21/2[64]
21/2[64]
NOTE: In horizontal configuration, return air cutout is not permitted.

6 Rheem Manufacturing Company
BLOWER PERFORMANCE DATA—UPFLOW/HORIZONTAL MODELS
MODEL RGPR-
BLOWER SIZE
(D X W)
INCHES [mm]
ECM
MOTOR H.P.
[W]
BLOWER
SPEED
CFM [L/s] AIR DELIVERY
EXTERNAL STATIC PRESSURE
INCHES WATER COLUMN [kPa]
.1 [.025]–.8 [.2]
05 11 x 7
[279 x 178]
3/4
[559]
HIGH
MED-HI
MED
LOW
1200 [566]
1000 [472]
800 [378]
600 [283]
07A 11 x 7
[279 x 178]
1/2
[373]
HIGH
MED-HI
MED
LOW
1200 [566]
1000 [472]
800 [378]
600 [283]
10, 12 11 x 10
[279 x 254]
1
[746]
HIGH
MED-HI
MED
LOW
2000 [944]
1600 [755]
1400 [661]
1200 [566]
07B 11 x 10
[279 x 254]
3/4
[559]
HIGH
MED-HI
MED
LOW
1600 [755]
1400 [661]
1200 [566]
1000 [472]
Note: See Coil Specification Sheet for coil data.
[ ] Designates Metric Conversions

Rheem Manufacturing Company 7
RETURN AIR CABINETS A
IN. [mm]
FILTER SIZE
IN. [mm]
RXGR-C17B 171/2[445] (2) 12 x 16 [305 x 406]
RXGR-C21B 211/4[533] (2) 20 x 16 [508 x 406]
RXGR-C24B 241/2[622] (2) 24 x 16 [610 x 406]
FILTER RACK FILTER SIZES† INCHES [mm]
MODEL
RGPR-
RXGF-CA
(SIDE)
05, 07*AMK 153/4x 25
[400 x 635]
07*BRQ, 10 153/4x 25
[400 x 635]
12 153/4x 25
[400 x 635]
†Filter racks are shipped without filters.
Filters shipped with furnace may be used or a suitable 1” [25.4 mm] filter.
*Designates “E” or “N”.
THE RXGR-C24B MUST ONLY BE INSTALLED ON THE SIDE
OPPOSITE THE GAS AND ELECTRICAL CONNECTIONS.
WARNING: IMPORTANT NOTICE
A SOLID METAL BASE PLATE (SEE TABLE) MUST BE IN PLACE WHEN THE FURNACE
IS INSTALLED WITH SIDE AIR RETURN DUCTS. FAILURE TO INSTALL A BASE PLATE
COULD CAUSE PRODUCTS OF COMBUSTION TO BE CIRCULATED INTO THE LIVING
SPACE AND CREATE POTENTIALLY HAZARDOUS CONDITIONS.
FURNACE BASE
WIDTH SOLID BOTTOM BASE PLATE SIZE
IN. [mm] KIT NO. PLATE NO. IN. [mm]
171/2[445] RXGB-D17 AE-61874-02 151/8x 239/16 [384 x 598]
211/2[533] RXGB-D21 AE-61874-03 185/8x 239/16 [473 x 598]
241/2[622] RXGB-D24 AE-61874-04 255/8x 239/16 [651 x 598]
RXGW-B01 CHIMNEY ADAPTER
See Installation Instructions for application limitations.
FOR HIGH ALTITUDES:
HIGH ALTITUDE OPTION CODE: U.S. & Canada – 278
HIGH ALTITUDE KIT: RXGY-F13 (for all models)
NOTE: High altitude kits and options do NOT include additional
burner orifices. If a burner orifice change is necessary, they
must be ordered through PROSTOCK®.. See Installation
instructions for more information.
Option — 278 furnaces are shipped with #51 DMS orifices
installed. This is one drill size smaller than standard furnaces to
account for expected average elevations and heating values typically
seen in these areas.
CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines
when converting furnaces for high altitudes.
For all installations above 2000 ft. (including all option — 278
models), the burner orifice size needs to be recalculated and
verified. A burner orifice change may still be required. See
Installation Instructions for more information.
NOTE: For Canadian installations only, an optional derate (manifold
gas pressure reduction) method may be used to adjust the
furnace for altitude. See Installation Instructions for more
information. This optional method may NOT be used for U.S.
installations.
(U.S. Models—Kit packaged with furnace.
Requires field installation).
[ ] Designates Metric Conversions
INTERNAL FILTER RACK FOR BOTTOM
OR SIDE RETURN: RXGF-DA*
*Filters available through PROSTOCK®.
SIDE RETURN FILTER RACK: RXGF-CA
BOTTOM RETURN FILTER RACK FOR
UPFLOW APPLICATION: RXGF-CB
ACCESSORY RETURN
AIR CABINETS
Return Air Cabinets may
be installed on either side
application except RXGR-C24B
(side application must be
on side opposite gas and
electrical connections).
RXPF-F01 and F02
FOSSIL FUEL KIT—is for use with Rheem Heat Pumps and
Super Quiet 80 warm air furnaces. RXPF-F02 also meets TVA
requirements.
ACCESSORIES—UPFLOW

Before proceeding with installation, refer
to installation instructions packaged
with each model, as well as complying
with all Federal, State, Provincial, and
Local codes, regulations, and practices.
RHEEM
AIR CONDITIONING
DIVISION
5600 Old Greenwood Road, Fort Smith, Arkansas 72908
“In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.”
PRINTED IN U.S.A. 8-07 DC FORM NO. G11-489 REV. 1
Supersedes Form No. G11-489