RHINO 2410 User manual

2-7702
Page 1 of 4F-4259 06-02-09
DELUXE QUICK ATTACH DEVICE
SKID STEER ATTACHMENT COMPATIBLE
RHINO 2410 LOADER
ASSEMBLY MANUAL
Keep With Operator’s Manual
Quick attach device can be installed using tools ordinarily
available.
Torque all hardware to specications listed in loader
operator’s manual.
Shut off the tractor engine and engage the tractor brakes
during installation.
Only quick attach, skid steer compatible attachments
can be used with the quick attach device. Pin on style
attachments can be used on the loader, but necessitate
removal of the quick attach device and relocation of the
bucket level indicator.
All references to left and right used in these instructions
are as they would appear to the operator standing at the
rear of the unit facing forward.
ASSEMBLING QUICK ATTACH DEVICE
(Figure 1)
1. Quick attach device is pre-assembled at the factory.
2. Unband the quick attach device (1) and wood blocks.
3. Cut wire securing spacers (15) and discard cut wire.
INSTALLING QUICK ATTACH DEVICE
(Figures 1 & 2)
WARNING: Always use a drift and hammer
made of non-sparking material (a shot-lled
mallet is recommended) to install or remove
pins. A steel hammer or drift could generate
ying metal fragments and result in injury.
Always wear safety glasses when using a
hammer to remove or install pins.
1. Fasten quick attach device to lower boom arms and
bucket tilt cylinders using four anti-rotation pins, 3/8 x
3/4” shoulder bolts, and 3/8” lock nuts (supplied with
loader). Place one loose spacer (15) between side
of the rod end of the bucket tilt cylinder and inside of
quick attach ear on each side. (Figure 2)
2. Attach bucket leveling rod indicator (supplied with
loader), to outside of right ear on quick attach as
shown in gure 2. Secure bucket leveling rod indicator
with two 1/8 x 1” cotter pins (supplied with loader).
MOUNTING ATTACHMENT TO LOADER
(Figures 1 & 2)
WARNING: To avoid injury during installa-
tion of the loader attachment, do not allow
bystanders within 10 feet of loader or attach-
ment.
1. Locate tractor and attachment on level ground.
Lower boom to rest on the ground. Extend the bucket
cylinders slightly, while raising the boom to provide
three to ve inches of ground clearance, drive the
tractor ahead slowly toward the attachment, aligning
the loader quick attach device as shown in gure 2.
2. While driving the tractor ahead slowly to maintain
contact with the attachment, activate the lift cylinders
to raise the loader until the quick attach engages
under the attachment lip.
3. Then activate bucket cylinders to retract, continuing
to roll the attachment back completely.
4. Place tractor in neutral, set parking brake, shut
off tractor. Move latch pin handles to latch (down)
position (refer to gure 2).
5. Start tractor activate lift cylinders to raise attachment
one or two feet off the ground and extend bucket
cylinders to tilt attachment at a slight downward angle,
so quick attachment latch pins are visible. Visually
inspect the attachment mechanism to verify that the
pins are engaged through the latch plate on the back
of the attachment.
NOTE: If the attachment is not securely attached,
follow the instructions for detaching it and repeat the
above procedure.

2-7702
Page 2 of 4F-4259 06-02-09
PARTS LIST - QUICK ATTACH DEVICE (Figures 1 & 2)
ITEM DESCRIPTION QTY.
1 55499 FRAME ASSEMBLY 1
2 48686 HANDLE 2
3 6075-4 FITTING, Grease, 1/4”-28 4
4 G9413315 SPRING PIN, 1/4” x 1-1/2” 2
5 6543-7 NUT, Jam, 1/2” 2
6 47408-1 DISC SPRING 2
7 47615 PIVOT ASSEMBLY 2
8 47394 PIVOT PIN 2
9 41903-1 COTTER PIN 5/32” x 1” 2
10 47618 SPADE BOLT ASSEMBLY 2
11 47614 SPRING 2
12 41902-14 PIN, CLEVIS 2
13 48687 PIN, LATCH 2
14 47526 SPRING GUIDE ASSEMBLY 2
15 54751-1 SPACER 4
16 55580 SHEET, DECAL (Includes two decals) 1
Figure 1
Quick Attach Device

2-7702
Page 3 of 4F-4259 06-02-09
DETACHING QUICK ATTACH DEVICE
(Figures 1 & 2)
WARNING: To avoid injury during installa-
tion/removal of the loader attachment, do not
allow bystanders within 10 feet of loader or
attachment.
1. Locate tractor and loader on level ground.
Figure 2
Quick Attach Device
2. Lower boom arms until the attachment is level and
resting on ground.
3. Place tractor in neutral, set parking brake, shut off
tractor engine and disengage quick attach device
latch pins by moving handles to unlatch position.
4. Start tractor engine, release brake and extend
bucket cylinders while slowly backing the
tractor away from attachment, until quick attach
disengages from attachment.

2-7702
Page 4 of 4F-4259 06-02-09
INSTALLATION
INSTRUCTIONS
GENERAL TORQUE SPECIFICATIONS
USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN
AMERICAN STANDARD CAP SCREWS METRIC CAP SCREWS
SAE
Grade 5 8 Metric Class 8.8 10.9
Typical
Grade ID
Markings
on Head
Typical
Grade ID
Markings
on Head
Cap
Size
Inches
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
7/8-14
1-8
1-14
Screw
MIN MAX MIN MAX
FT-LBS N·m
6.25 7.25 8.5 10
8 9 11 12
14 15 19 20
17.5 19 23 26
26 28 35 38
31 34 42 46
41 45 55.5 61
51 55 69 74.5
65 72 88 97.5
76 84 103 114
95 105 129 142
111 123 150 167
126 139 171 188
152 168 206 228
238 262 322 355
274 305 371 409
350 386 474 523
407 448 551 607
537 592 728 802
670 740 908 1003
TORQUE
MIN MINMAX MAX
FT-LBS N·m
8.25 119.5 13
10.5 1412 16
18.5 2520 27
23 3125 34
35 47.537 50
41 55.545 61
55 74.560 81
68 9275 102
86 11696 130
102 138112 152
127 172140 190
148 200164 222
168 228185 251
203 275224 304
318 431350 474
365 495402 544
466 631515 698
543 736597 809
716 970790 1070
894 1211987 1337
TORQUE
MINMINMINMIN MAXMAXMAXMAX
FT-LBSFT-LBS N·m N·mSize
Millimeters
12986 1511118M6 x 1.00
312321.516 36.5272720M8 x 1.25
57423929 70524735M10 x 1.50
102757052 123918462M12 x 1.75
16312011585 198146139103M14 x 2.00
238176176130 293216214158M16 x 2.50
325240233172 398294284210M18 x 2.50
465343335274 577426408301M20 x 2.50
639472450332 780576547404M22 x 2.50
812599573423 992732700517M24 x 3.00
1217898863637 148810981055779M27 x 3.00
165812241181872 2027149614441066M30 x 3.00
Cap Screw TORQUETORQUE
NOTE: These values apply to fasteners as
received from the supplier, dry or when lubricated
with normal engine oil. They do not apply if special
graphite or molydisulphide greases or other
extreme pressure lubricants are used.