RHINO RHINO 2409 User manual

F-3926 1 of 6 3-23-04
2-7233
ASSEMBLY MANUAL
Keep With Operators Manual
LOADER MOUNT KIT
2409 LOADER
AGCO ST45, ST55 and MASSEY FERGUSON 1165, 1445,
1455, 1455V TRACTORS
Mount kit can be installed using tools ordinarily
available. Shut off engine and engage brakes during
installation.
Check tire clearances once loader is installed and adjust
tire tread width and/or turning radius if necessary.
NOTE: Unless specified, leave all attaching hardware
loose until loader is completely assembled to facilitate
assembly and proper alignment. Torque hardware to
specifications listed on page 5.
TRACTOR PREPARATION
1. Shut off engine and engage brakes during
installation of mount kit.
2. Remove front weight bracket.
3. Raise hood and remove hood side panels to prevent
damage during loader mount installation.
INSTALLING LOADER MOUNT BRACKETS
(Figure 1)
1. Attach front mount bracket (3) using 14MM x 35MM
cap screws (9) and 9/16 lock washers (15).
2. Remove and discard 14MM cap screws and lock
washers where mid mount brackets are bolted to
tractor frame.
3. Attach mid mounting brackets (1 & 2) to mounting
pads below tractor platform using 16MM x 40MM cap
screws (6) and 5/8 lock washers (10). Leave 16MM
cap screws (6) and 5/8 lock washers (10) loose to
ease installation.
A) AGCO ST45, MF1165 and MF 1445 requires two
5/8 spacers (5) each side between mid mounting
bracket and tractor frame.
B) AGCO ST45, MF1165 and MF1445 - Install mid
mounting bracket (1 & 2) to tractor frame using
14MM x 60MM cap screws (7), 9/16 flat washers (14)
and 9/16 lock washers (15).
C) AGCO ST55, MF1455 and MF1455V - Install mid
mounting brackets (1 & 2) to tractor frame using
14MM x 40MM cap screws (8), 9/16 flat washers (14)
and 9/16 lock washers (15).
To access bottom hole on frame, 14MM bolt (7 or 8),
9/16 flat washer (14) and 9/16 lock washer (15) must
pass through support tube of mid mounting
assembly (1 & 2).
4. Reinstall hood side panels and lower hood to locked
position.
MODEL 2WD FWA CAB LESS CAB
AGCO ST45 X X
AGCO ST55 XX
MF 1165 X X
MF 1445 X X
MF 1455 X X
MF 1455V X X

3-23-04 2 of 6 F-3926
2-7233
1
7 8
7
15
14
6
5
10
9
15
3
9
15
6
10
5
2
14
15
78
78
12 4
13
11
NOTES:
Items5&7usedfor
MF1445, MF1165 & AGCO ST45.
Item 8 used for
MF1455, MF1455V & AGCO ST55.
Bolt items 2 & 3 to tractor
frame through support
tube of mountings.
Figure 1
Mount Kit

F-3926 3 of 6 3-23-04
2-7233
PARTS LIST - MOUNT KIT
ITEM Part No. DESCRIPTION QTY.
1 52004 MID MOUNTING ASSEMBLY, Left 1
2 52005 MID MOUNTING ASSEMBLY, Right 1
3 52017 FRONT MOUNT ASSEMBLY 1
4 52138 YOKE ASSEMBLY, with Decal 1
5 43395-6 SPACER, Tube 5/8 YDP 4
6 42672-15 SCREW, Cap, 16MM-2.00MM x 40MM 8
7 42672-43 SCREW, Cap, 14MM-2.00MM x 60MM 4
8 42672-46 SCREW, Cap, 14MM-2.00 x 40MM 4
9 42672-51 SCREW, Cap, 14MM-2.00 x 35MM 8
10 41837-7 WASHER, Lock, 5/8 YDP 8
11 41840-8 NUT, Lock, 3/4-10 YDP 4
12 41838-7 SCREW, Cap, 3/4-10 x 2.50 YDP 4
13 39240 DECAL, “WARNING, Do Not Use For Towing” 2
14 42502-11 WASHER, Flat, 9/16” 4
15 41837-6 WASHER, Lock, 9/16” 12
INSTALLING YOKE ONTO LOADER
WARNING: Be sure to support loader
using an overhead hoist. Boom may fall
causing serious personal injury permit.
Install yoke assembly (4) using 3/4 x 2-1/2 cap screws
(12) and 3/4 lock nuts (11). Install rear cap screws first,
then swing yoke into position and install front cap
screws.
IMPORTANT: Install 3/4 x 2-1/2 cap screws (12) from
the inside with lock nuts (11) on the outside of yoke.
NOTE: Hardware connecting yoke to loader side
frames should be snug, but do not torque completely.
After loader has been mounted to tractor and aligned
with mid mounting brackets and front mounting
brackets, torque hardware to 239-262 ft.-lb.
INSTALLING LOADER TO MOUNTING
BRACKETS
WARNING: To avoid injury during
installation of quick attach loader, do not
permit bystanders within ten feet of loader.
1. Remove hardware which secures loader to pallet.
Using overhead hoist, lower loader from vertical
shipping position to horizontal position (use scraps
of cardboard to protect paint).
2. Reposition overhead hoist by looping nylon strap
around yoke near loader side frames at balance
point of loader.
3. Using overhead hoist, raise loader until side frame
uprights will clear front tires. Remove lock nut and
washer from loader hinge and swing each hinge
open..
Fasten rear
bolt first.
Swing yoke
into position.
Balance point
of loader

3-23-04 4 of 6 F-3926
2-7233
INSTALLING LOADER TO MOUNTING BRACKETS
(Continued)
4. Install hose or valve kit to tractor and loader. Refer
to installation instructions provided with hose or
valve kit.
5. Position loader so hinges hook over mid mounting
tubes and yoke tube fits inside front mounting
bracket.
6. Clamp hinges to mid mounting tubes with 3/4 flat
washers and 3/4 flex-lock nuts (supplied with
loader).
IMPORTANT: Be sure to use flex-lock nuts to clamp
hinge. Tighten flex-lock nuts against hinge securely,
but not to more than 125 ft.-lb. Torque.
7. Adjust front wheel tread settings of steering stops, if
necessary to prevent interference between tires
and loader. Refer to tractor operator’s manual for
adjustment procedures.
8. Install hose or valve kit to tractor and loader. Refer
to instructions provided for installation instructions.
INSTALLING BUCKET OR OPTIONAL
ATTACHMENT
Refer to instructions provided with bucket or loader
attachment to install bucket or attachment onto loader.
INSTALLING BUCKET LEVEL INDICATOR
1. Attach indicator guide tube to cylinder pin. Guide
tube is positioned to outside of boom for pin on
attachments and inside of boom when quick attach
device is used.
2. Slide bucket level indicator rod through guide tube.
Attach other end of rod with 1/8 x 1 cotter pins and
3/8 flat washers.
3. Locate tractor and loader on level surface. With
bottom of bucket resting on surface, cut off excess
rod flush with end of guide tube or paint exposed
rod a contrasting color.
Hinge open

F-3926 5 of 6 3-23-04
2-7233
AMERICAN STANDARD CAP SCREWS METRIC CAP SCREWS
GENERAL TORQUE SPECIFICATIONS
USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN
SAE Grade
Typ. Head
Markings
Metric Class
Typ. Head
Markings
5 8 8.8 10.9
Cap Screw TORQUE TORQUE TORQUE TORQUE
Size FT·LBS N·m FT·LBS N·m FT·LBS N·m FT·LBS N·m
Inches MIN MAX MIN MAX MIN MAX MIN MAX
6.25 7.25 8.5 10 8.25 9.5 11 13
8 9 11 12 10.5 12 14 16
14 15 19 20 18.5 20 25 27
17.5 19 23 26 23 25 31 34
26 28 35 38 35 37 47.5 50
31 34 42 46 41 45 55.5 61
41 45 55.5 61 55 60 74.5 81
51 55 69 74.5 68 75 92 102
65 72 88 97.5 86 96 116 130
76 84 103 114 102 112 138 152
95 105 129 142 127 140 172 190
111 123 150 167 148 164 200 222
126 139 171 188 168 185 228 251
152 168 206 228 203 224 275 304
238 262 322 355 318 350 431 474
274 305 371 409 365 402 495 544
350 386 474 523 466 515 631 698
407 448 551 607 543 597 736 809
537 592 728 802 716 790 970 1070
670 740 908 1003 894 987 1211 1337
MIN MAX MIN MAX MIN MAX MIN MAX
688119111215
16 20 21.5 27 23 27 31 36.5
29 35 39 47 42 52 57 70
52 62 70 84 75 91 102 123
85 103 115 139 120 146 163 198
130 158 176 214 176 216 238 293
172 210 233 284 240 294 325 398
247 301 335 408 343 426 465 577
332 404 450 547 472 576 639 780
423 517 573 700 599 732 812 992
637 779 863 1055 898 1098 1217 1488
872 1066 1181 1444 1224 1496 1658 2027
1/4 - 20
1/4 - 28
5/16 - 18
5/16 - 24
3/8 - 16
3/8 - 24
7/16 - 14
7/16 - 20
1/2 - 13
1/2 - 20
9/16 - 12
9/16 - 18
Cap Screw
Size
Millimeters
M6 x 1.00
M8 x 1.25
M10 x 1.50
M12 x 1.75
M14 x 2.00
M16 x 2.50
M18 x 2.50
M20 x 2.50
M22 x 2.50
M24 x 3.00
M27 x 3.00
M30 x 3.00
5/8 - 11
5/8 - 18
3/4 - 10
3/4 - 16
7/8 - 9
7/8 - 14
1 - 8
1 - 14
Standard American and Metric Cap Screws
NOTE: These values apply to fasteners as received
from supplier, dry or when lubricated with normal
engine oil. They do not apply if special graphite or
molysulphide greases or other extreme lubricants are
used.

3-23-04 6 of 6 F-3926
2-7233
INSTALLATION
INSTRUCTIONS