OE electrics INSTR1292 User manual
(3.54”)
90.00mm
(15.16”)
385.00mm
(4.04”)
102.51mm
(4.33”)
110.00mm
MINIMUM
CABLE CLEARANCE
10.00mm
19.00mm
(14.37”)
365.00mm
(2.76”)
70.00mm
(0.47”)
MAX
R12.00mm
(4.43”)
112.51mm
(15.70”)
398.70mm
(0.24”)
6.00mm
(3.78”)
96.00mm
(15.16”)
385.00mm
(4.72”)
120.00mm
MINIMUM
CABLE CLEARANCE
(4.72”)
120.00mm
MINIMUM
CABLE CLEARANCE
(1.08”)
27.50mm
(15.22”)
386.70mm
(0.98”)
25.00mm
QIKPAC CARRY FLUSH WITH FRONT EDGE
FRONT EDGE
OF SURFACE
CLAMP FIX (IN SURFACE) SCREW FIX (UNDER SURFACE)
(1.08”)
27.50mm
(15.22”)
386.70mm
(0.63”)
16.00mm
FRONT EDGE
OF SURFACE
QIKDOC FLUSH WITH FRONT EDGE
(3.54”)
90.00mm
(15.16”)
385.00mm
(4.04”)
102.51mm
(4.33”)
110.00mm
MINIMUM
CABLE CLEARANCE
10.00mm
19.00mm
(14.37”)
365.00mm
(2.76”)
70.00mm
(0.47”)
MAX
R12.00mm
(4.43”)
112.51mm
(15.70”)
398.70mm
(0.24”)
6.00mm
(3.78”)
96.00mm
(15.16”)
385.00mm
(4.72”)
120.00mm
MINIMUM
CABLE CLEARANCE
(4.72”)
120.00mm
MINIMUM
CABLE CLEARANCE
(1.08”)
27.50mm
(15.22”)
386.70mm
(0.98”)
25.00mm
QIKPAC CARRY FLUSH WITH FRONT EDGE
FRONT EDGE
OF SURFACE
CLAMP FIX (IN SURFACE) SCREW FIX (UNDER SURFACE)
(1.08”)
27.50mm
(15.22”)
386.70mm
(0.63”)
16.00mm
FRONT EDGE
OF SURFACE
QIKDOC FLUSH WITH FRONT EDGE
QIKDOC Connect Clamp Fix instructions
INSTR1292
www.oeelectrics.com
UK -
Cutout Size
Align clamp brackets with QIKDOC and
screw into place using screws provided
(a T10 Torx bit is required)
1
3 4
Fit QIKDOC into surface
2
Tighten bolts
Required clearance
5
CAUTION Do not overtighten
Align QIKPAC CARRY with QIKDOC, slide the heel side of the QIKPAC
CARRY into QIKDOC rst and rotate down until click is heard
Rear View
For surfaces 12mm (0.47”) - 39mm (1.54”) thick
COMBINED OUTPUT
RATING 144W MAX
*SIT STAND MECHANISM CAN BE CONNECTED TO EITHER END OF THE QIKDOC,
BUT THE SECOND OUTPUT AT THE SAME END OF THE QIKDOC SHOULD NOT
THEN BE USED (OTHERWISE BATTERY OVERLOAD AND SHUTDOWN MAY OCCUR)
COMBINED OUTPUT
RATING 144W MAX
Power
Output
Power
Output
Power
Input
Power
Output
Power
Output
QIKDOC Connect Clamp Fix instructions
INSTR1292
www.oeelectrics.com
UK -
6Pull thumb release (highlighted
orange) to release QIKPAC CARRY
Removing QIKPAC CARRY from QIKDOC
8
Lift QIKPAC CARRY from QIKDOC
7
Connect GST08 cable(s) to underside of QIKDOC (where applicable*)
Rear View
Align plug with QIKDOC as shown, ensure
text is facing outward on GST08 cable prior
to insertion as shown. Do not force cables
into connectors
QIKDOC Connect Clamp Fix instructions
INSTR1292
www.oeelectrics.com
UK -
Cable tie GST08 cable(s) into place
Slide cable tie through slot Fold cable tie over cable Tighten cable tie & remove excess
9
Other OE electrics Rack & Stand manuals
