RiverRidge 02-068 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Kids 3 TIER LADDER SHELF
ITEM #:02-068 WHITE
ITEM #:02-069 GRAY
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of the small parts. Care should be
taken in unpacking and assembling this item to keep the small parts away from children.
WARNING
Young children can be seriously injured or killed, if furniture tips over.
Don’t use this item for a TV stand.
Use angle-braces or anchors to secure furniture to the wall.

Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR A TOTAL OF 60 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS.IF LOADED WITH MORE THAN 20
POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS
INJURY OR DEATH.

Wood Dowel
Cam Bolt
Cam Lock
Machine Screw (Φ6 x 20mm)
Wood Screw (Φ3.5 x 20mm)
Wall Screw (Φ3.5 x 30mm)
Wood Screw (Φ3.5 x 8mm)
Plastic Anchor
Bracket
Plastic lock strap
top shelf left rail board
top shelf right rail board
middle shelf left rail board
middle shelf right rail board
bottom shelf left rail board

Top bar of left and right
side frame
Left side front leg
Left side rear leg
Right side front leg
Right side rear leg
bottom shelf right rail board
top shelf
middle and bottom shelf
Rear rail board
Top rear rail board
TOOLS NEEDED FOR ASSEMBLY : FLAT & PHILIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENED

1.Insert 1pc Wood dowel(A) into the wood dowel hole on the end of Top rear rail board(10)
2.Attach the top shelf left rail board(1) to Top rear rail board(10) by inserting the Wood
dowel(A) into the hole on the top shelf left rail board(1).Make sure the hole on the Top
rear rail board (10) is facing towards the back side of the shelf.
3.Insert 1pc Wood screw(E) through the hole on the top shelf left rail board(1) and tighten
it to the Top rear rail board(10) by using a Philips Screwdriver.
4.Repeat above steps to assemble the top shelf right rail board(2) to the Top rear rail
board (10).
1.Insert 1pc Wood dowel(A) into the wood dowel hole on the end of Rear rail board(9)
2.Attach the middle shelf left rail board(3) to Rear rail board(9) by inserting the Wood dowel(A)
into the hole on the middle shelf left rail board(3).
3.Insert 1pc Wood screw(E) through the hole on the middle shelf left rail board(3) and tighten
it to the Rear rail board(9) by using a Philips Screwdriver.
4.Repeat above steps to assemble the middle shelf right rail board(4) to the Rear rail board (9).

1.Insert 1pc Wood dowel(A) into the wood dowel hole on the end of Rear rail board(9)
2.Attached the bottom shelf left rail board(5) to Rear rail board(9) by inserting the Wood dowel(A)
into the hole on the bottom shelf left rail board(5).
3.Insert 1pc Wood screw(E) through the hole on the bottom shelf left rail board(5) and tighten it to
the Rear rail board(9) by using a Philips Screwdriver.
4.Repeat above steps to assemble the bottom shelf right rail board(6) to the Rear rail board (9).
1.Insert 6pc Wood dowels(A) into the wood dowel holes on the top shelf(7).
2.Attach the top shelf(7) to the Top Shelf rail board assembly of parts(1)(2)(10) by inserting the
Wood dowels(A) into the wood dowel holes on the Top shelf Left rail board(1)，Top Shelf Right
rail board(2) and Top rear rail board（10）.
3.Insert 7pc Wood Screws(E) through the holes on the top shelf(7) then tighten to Top Shelf Left
rail board(1), top Shelf Right rail board(2) and Top rear rail board(10) by using a Philips
screwdriver.

1.Insert 6pc Wood dowels(A) into the wood dowel holes on the middle shelf(8).
2.Attach the middle shelf(8) to the Middle Shelf rail board assembly by inserting the Wood
dowels(A) into the wood dowel holes on the Middle Shelf Left rail board(3),Middle Shelf Right
rail board(4) and Rear rail board(9).
3.Insert 7pc Wood Screws(E) through the holes on the middle shelf(8) then tighten to Middle
Shelf Left rail board(3),Middle Shelf Right rail board(4) and Rear rail board(9) by using a
Philips screwdriver.
1.Insert 6pc Wood dowels(A) into the wood dowel holes on the bottom shelf(8).
2.Attach the bottom shelf(8) to the Bottom Shelf rail board assembly by inserting the Wood
dowels(A) into the wood dowel holes on the Bottom Shelf Left rail board(5), Bottom Shelf
Right rail board(6) and Rear rail board(9).
3.Insert 7pc Wood Screws(E) through the holes on the bottom shelf(8) then tighten to Bottom
Shelf Left rail board(5). Bottom Shelf right rail board(6) and Rear rail board(9) by using a
Philips screwdriver.

1.Insert 2pc Wood dowels(A) into the wood dowel holes on the Top bar(11).
2.Screw 2pc Cam bolts(B) into the pre-threaded holes on the Top bar(11).
3.Attached the top bar(11) to the Left side front leg(12) and Left side rear leg(13) by insert the
Wood dowels(A) into the wood dowel holes and insert 2pc Cam bolts(B) into the cam lock holes
on the Left side front leg(12) and Left side rear leg(13).
4.Insert 2pc Cam locks(C) into the cam lock holes on the Left side front leg(12) and Left side rear
leg(13), then rotate clockwise to secure the cam bolts in place.
5.Repeat above steps to assemble the other Top bar(11) to Right side front leg(14) and Right
side rear leg(15).
1.Attach the Pre-assembled top shelf(7) and rail boards to Pre-assembled Right side frame,
insert 6pc Machine screws(D) through the holes on the Right rail board(2) and tighten to the
Pre-assembled Right side frame.
2.Repeat above step to assemble the middle and bottom shelf(8) to Pre-assembled Right side
frame.

1.Attach the Pre-assembled top shelf（7）and rail boards to Pre-assembled Left side frame,
1. Attach one bracket(J) to the back of the ladder shelf by inserting 1pc wood screw(G) through
the hole on the bracket(J) then tighten into the hole on the back side of Top rear rail board(10).
2. According to the height of bracket(J) that was assembled to the ladder shelf, drill one hole on
the wall.
3. Insert the Plastic anchor(H) into the hole on the wall.
4. Attach one bracket(J) to Plastic anchor(H) on the wall by inserting 1pc wall screw(F) through
the hole on the bracket(J) and tighten into the Plastic anchor(H).
insert 6pc Machine screws(D) through the holes on the Left rail board(1) and tighten to the
Pre-assembled Left side frame.
2.Repeat above step to assemble Middle and bottom shelf(8) to Pre-assembled Left side frame.
F
J
H
WALL
G
G
J
J

K
K
WALL
1. Place the ladder shelf against the wall and close to bracket(J).
2. Insert the Plastic lock strap(K) through the hole on the bracket(J) which is assembled on the
ladder shelf, then through the hole on the bracket(J) on the wall, then fasten the plastic lock
strap (K) to fix the 2 brackets(J) firmly.

ENJOY YOUR NEW RiverRidge® Kids 3 TIER KIDS LADDER SHELF NOW !
Attention Adults: The shelf should be checked periodically for damage or loose screws/parts.
Take appropriate action necessary to correct the hazard such as tightening of screws and taking
any damaged parts away from the children.
Thank you for purchasing this RiverRidge® Kids Products item. We hope you enjoy it, and
consider purchasing other RiverRidge® items.
Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016.