Rk Rko3500-02 User manual

1/10TH SCALE ELECTRIC

POWERED ROCK CRAWLER

14 +

Notes:

The radio controlled racing models is not toy. It is suited for experienced operators.

Read and understand the instructions carefully before operating or assembling your racing model.

Specifications are subject to change without prior notice, and actual received model may

vary from the images and/or descriptions in this manual.

INSTRUCTION MANUAL

2

1

Additional Items Needed For Running Your Model

Use of the transmitter to control your EP vehicle...

Please install eight "AA" batteries to the transmitter.

Slide the battery cover to open the

battery compartment.

Replace the battery cover after

eight AA batteries are installed.

1

23

10

Function Switches On This Transmitter

1.Throttle Reverse Switch

2.Steering Reverse Switch

Battery Precautions:

1.In order to maintain good performance ,we warmly recommend you to use the 1.5V

alkaline batteries instead of the 1.2 V chargeable batteries.

2.The batteries may leak in the event that they are installed with wrong polarities.

3.Do not use batteries of different types.

4.Do not mix the old and new batteries.

5. Please replace batteries when power indicators are weak.

7

8

10.Power Switch

1. Trigger at the neutral position

3. Release the trigger back to neutral

position to slow down the car.

2. Pull the trigger inwa rd to drive

the car forwa rd.

4. Push the trigger outwa rd to stop

the car imme diately comp letely

(breaking)

5. Release the trigger back to

the neutral position again

(require d step to activate the

backward feature on the ESC)

6. Push the trigger outwa rd again

to drive the car backwa rd.

Length...........450mm Width...........258mm

Height......................200mm(body excluded) Gear Ratio...........1:48

Wheel Diameter........126mm Wheelbase................320mm

Wheel Width................56mm Weight.................. .

Motor.......................7.2V RC540 Battery....................7.2V SC2000mAh NI-mh

/ 470mm(Extra loner version)

2100g

Technical Data:

RC540 motor

ESC w/reverse

speed control

Include 7.2V rechargable

rechargable battery

Quick-release battery cover

4WD for optimal

power delivery

Axle-mounted

steering servo

aluminum links

Plastic bumper

Anodized chassis and

side plates

2-channel pistol-grip radio

Adjustable width body mounts

Oil shocks with

anodized aluminum

Locked front and rear spool

for maximum power

Steering Angel:40-50

Maximum Torque Angel:90

Air Current:about 1A,Climb Current:about 15A

1/10th Electric Powered Crawler is equipped with single motors,a lot of metal parts to

make sure the construction solidly.The high precision ESC is also equipped on the Car.

You are not only have a chance to see the beautiful nature scene but also climb over the

most chanlleging rugged terrain.

A

Transmitter

4

5

6

3.Control Wheel

4.Steering Trim

5.Throttle Trim

6.Trigger

7.Crystal(To change please pull out)

8.Power Indicators

9.Trigger Setup Trim

9

10

1.It is used for the crawler only.

2.It contains various steering modes which makes the crawler

perfect for crawling on road or rocks.

3.Fully extend its antenna while using it.

4.Various frequencies of AM crystals are available at factory

5.This radio control is a high precision product and allowed itself to

be used with your good care.

1.Antenna

2.LCD Screen

3.Steering Control Wheel

4.Steering Trim/Reverse Switch

5.Throttle Trim

6.Power Switch(Slide it to turn on/off)

7.Working Indicator

8.Servo steering Trim(Angel)

9.Trigger

10.Trim Switch(rear wheels)

12.SEL function button

11.Steering Mode Switch

General information

Full function AM radio controller

This AM radio controller contains various steering modes

which are perfect for the rock crawler.

MODE 1 MODE 2

This illustration is your crawler in the situation by

performing the first mode on the radio control.

Front steering is to turn to the left or right but

rear steering remains aligned.

This illustration is your crawler in the situation by

performing the second mode on the radio control.

Front steering is to turn to the left and rear steering

is to do likewise.

Full function steering modes

Steering Trim/Steering Reverse Function

TRM.ST(Steering Trim)range is around 0-10.0% for both left and right steering on front wheels.

Tune this switch to select your desired steering trim volume.

To switch to steering Reverse program:

Press SEL(Select Button)on your radio once,this LCD display appears Channel 1(NOR)

Tune the Switch(Steering Trim/Reverse Switch)to change NOR into the REV as shown below:

1

2

6

7

9

11

12

10

8

3

4

5

12.8v 12.8v

NO 1 NO 1

Your crawler will

work like so:

Your crawler will

work like so:

LCD Screen LCD Screen

MODE 4

MODE 3

This illustration is your crawler in the situation by

performing the third mode on the radio control.

Front steering is to turn to the left but rear steering

is to trun right.

This illustration is your crawler in the situation by

performing the fourth mode on the radio control.

Rear steering is to turn to the left or right but front

steering remains aligned.

12.8v

NO 1 NO 1

Your crawler will

work like so:

Your crawler will

work like so:

LCD Screen

To open the battery door

To close the battery door

TRM.ST

10.0%

R.B.D

CH1

TRM.ST

10.0%

CH1

L.F.U

Throttle Trim/Throttle Reverse Switch

10.0%

R.B.D

CH2 CH2

10.0%

L.F.U

TRM.TH(THrottle Trim)range is around 0-10%.Tune this switch to select your desired throttle trim volume.

CH1

REV

NOR

CH2

REV

NOR

To switch to Throttle Reverse program:

Press SEL(Selecct Button)on your radio once,this LCD display appears Channel 1(NOR.)

Tune the SWITCH(Steering Trim/Reverse Switch)to change NOR into REV as shown below:

This dial adjusts the overall travel of the steering servo,push

the dial forward for maximum steering.Pull the dial back to reduce

steering travel.D/R adjustable range is around 5-10%

This dial is to centre the rear wheels.The

range is around 0-10% on the left or right

rear wheel.

Steering Dual Rate Control Dial(D/R)

Pull back Pull back

Push forward Push forward

D/R

10.0% 10.0%

CH1 CH3

Trim Switch(For Rear Wheels)

It controls the steering of your rock crawler.Turn the wheel to the right and

your crawler turns right.Turn the wheel to the left and your crawler turn left.

It controls the speed and braking ability of your rock crawler.Pull the trigger

to speed up.release the trigger to decelerate,and push the trigger to brake.

Pushing the trigger a second time and activates the reverse function.

Throttle/Brake Trigger

SEL funciton button

This AM radio controller contains a variety of select functions.Once your press SEL button,different

functions will come up in turn with LCD indicators on.

B(Optional)

34

Good performance of EP vehicles rely on the Electronic speed controller and motor, The new style

ESC(18051)works on 1/10 Crawler ,is a new kind of drive FET amp with high frequency and reverse function.

Unlike the other ESC,the setting have been simplied.,It is suitable for the novice and the experience operator.

If the running speed is bigger than the original data of ESC,the ESC will update the full speed automatically,

forward means forward,backward means backward,center position means brake automatically.

Electronic Speed Controller-ESC(18051)

Technical Data

BEC:5V 1A

●Input Voltage:6V-8.4V DC

●

Current Capacity(FET range):Forward=100A;Backward=50A

●

Case Dimensions:L35*W33*H30(include protective heat guard)

Weight:46.3g

Correspond Motor:540/23T or above

Note:

1.The ESC is not waterproof,so the water can’t flow into the ESC.The battery plug should pull

outed immediately once water flowed,use the blower to dry it before electrify test.

2.The ESC is hot in use.and the Heat Guard of ESC is very high after operation.so it can’t be

touched in use or after operation.

Connections

Pu sh b ut to n

(Red)

(B la ck )

(Red)

Power Sw i t c h

Motor Connector

Note: Red is "+",and Black is "-".

Reverse connectors if the motor works in the wrong

direction.

Battery connector

Note: Red is "+",and Black is "-".

Receiver connector

It will be connected to the receiver throttle channel.

(Reset Button)

Connector Setting:

1.Neutral Set:The ESC sustain the car foward,backward with a distance 50%/50%&70%/30%center position

of transmitter motor control mode. While you adjust to the above mode.We recommend you adjust the

speed range of transmitter to the normal.The ESC will update the full speed automatically.The LED blink

in red and yellow indicates searing the neutral

2.According to the diagram above,perform the correct collections,turn on the transmitter then the ESC,

Once ESC is turned on,it automatically switched to Neutral,you can hear a subtly confirmed sound(DO,

RE MI)that indicates ESC is set at netural .If the motor can’t stop running after the neutral position is

settd for a period of time,please close the ESC switch then reopen it,the neutral position should be reset it.

Features:

1.Pull your transmitter trigger back to expect your car to go forward.in this way,LED is supposed to blink

slowly in red.As the running speed of your Car rises,LED blink faster.If the full speed reaches,LED will

become steady in red.

2.Push the trigger outward to stop the car immediately(breaking).LED blink slowly in red,If the full speed

of brake reaches,LED will become steady in red.

3.Push the trigger outward again to drive the car backward.LED blink slowly in red.If the full speed reaches,

Led will become steady in red.

Rear Unit

Front Unit

2

1

18025

18007

18041

18008

18001

Sp9001

18016

18012

18006

18004

18032

18040

18009

18003

18043

98066

18035

18034

18032

18005

18041

18032

18005

18044

18041

18052 18052

18021

18042

18033

02030

98068

9806818041

18002

18034

18033

98055

18021

18044

98069

18016

18033

18007

18040

18001

18043

98066

18034

18032

18016

18033

18032

18004

18016

18012

98068

18041

18042

18033

18034

98055

18003

98069

18035

18004

18041

18005

18012

18002

98068

18035

18041

18006

18041

18009

02030

18036

18008

18032

18034

18009

18023

18015

18006

98068

18041

18048

56

Center Unit 367

18014

18049

18014

03011

18043

18045

18039

18045

03011

18014

18013

Tire Set Assembly 4

Servo Mount Assembly Set

Battery Assembly Set

Shock Absorber 5

18034

18024

18034

18024

98055

18024

18032

18024

18032

18024

18029

18024

02055

98068

18028

03070

18028

02053 02053 18010

18010

1801098069

98069

Crawler Exploded View

2

1

2

3

4

5

6

Front Unit

Rear Unit

Center Unit

Tire Set Assembly

3

4

5

6

Shock Absorber

Battery Assembly Set

18020

18023

18015

18020

18011

98068

02055

18011

18022

18026

18027

18034 18043

18043

98068

98055

18065

18043

78

18016-Wheel Hex.

W/Pins(2*10)

18018-Chassis

910

18020-Side Linkage

(133.5mm) 2P

18021-Servo Linkage

(60.23mm) 2P

18022-Center Linkage

(96mm) 2P

18023-Connect Linkage

(138mm) 2P

18017-Pre-Mounted

Tire Set 2P

18001-Front Gear Box

(Shell Only)

18002-Rear Gear Box

(Shell only)

18012-Wheel Axle

2P

18007-Drive Shaft(L)

2P

18009-Connect Box

w/main gear (38T)

18004-Caster Mounts

2P

18006-Steering Arm(L/R)

18003-Center Link

Ball Mounts

2P

18010-Servo Plate

w/servo mount

18013-Tire w/Foam 2P 18014-Rims/Secure Ring

2P

18005-King Pin Bushing

8P

18008-Drive Shaft(R)

2P

18011-Body Post 4P

02030-Drive Gear(13T)

02053-Body Clip 6P 18015-Adjustable Linkage

18024-Gear Box Set

18019-Shock Absorber

2P

(20T ) (28T)

(53T )

(87T )

(2*9m m)

(5*18mm)

(10*4 2mm)

(10*3 5mm)

(2.5* 17mm)

18026-Side Plate 2P

18027-Universal Driven

Dogbone 2P

18025-Bumper(F/R)

02055-Nylon Nuts M4

8P

Sp9001-Servo(9kg)

18028-Battery Holder

w/Covers

03020-Receiver

18029-ESC 03070-Battery

( NI-MH 7.2V 2000mAH) w/ Gear(14T)

03011-Motor(RC540)

18030-Ball Stand

6P

18052-Ball Stand

8P

18032-Ball Bearings

(10*15*4) 6P

whole part include the above parts

5.9 5.9

Please notice that the parts images with have several kinds of different

colors when place your order.

T2(Orange) T6(Green)

T3(Blue) Extra longer Version(Titanium)

Crawler Parts Spare

18033-Ball Bearings

(5*10*4) 8P

18034-Oil Bearings

(5*10*4) 8P

18035-E-Clips 8P

4.0

18036-E-Clips 4P

2.5

18037-Washer 6*2.7*0.5

6P

18038-Nylon Nuts M2.5

8P

98055-Nylon Nuts M3

8P

18039-M3*3

4P

11 12

18041-Round Head Screw

M3*10 8P

18042-Round Head Screw

M3*16 6P

18043-Round Head Screw

M3*20 6P

18044-Round Head Screw

M3*25 4P

18045-Round Head Screw

M3*24 6P

18046-Round Head Screw

M3*26 6P

18047-Countersink screw

M3*8 8P

18048-Countersink screw

M3*10 8P

18049-Column Head Screw

M2.5*5 8P

18050-Set Screw

M3*20 6P

18051-Set Screw M3*15

6P

98064-Round Head Screw

M3*12 8P

98066-Round Head Screw

M3*14 6P

98068-Round Head Screw

M3*8 8P

98069-Round Head Screw

M4*8 8P

18040-Round Head Screw

M2*10 6P

18055-Side Linkage

(160mm) 2P

18056-Servo Linkage

(70mm) 2P

18022-Center Linkage

(125mm) 2P

18023-Connect Linkage

(145mm) 2P

18019-Shock Absorber

2P

180001-Center Link

ball Mounts (AL). 2P

180004-Rims/Secure Ring

180007-Shock Absorber

2P 180008-Body Post 4P

(AL.)

(AL.) (AL.) 2P

(AL.)

AL.

Crawler Upgradable Optional

180006-Chassis

(AL.)

180009-Connect Box

180002-Caster Mounts

2P

180003-Steering Arm

(L/R)

180010-Servo Mount

( AL.) 2P

180012-Battery Holder

w/Covers (AL.)

180011-Universal Driven

Dogbone (AL.) 2P

180005-Bumper(F/R)

(AL.)

(W/Gear 38T)

Crawler Parts (Extra longer version) Spare

Color:orange/green/blue/titanium

Please notice that the following Upgradable Optional have several kinds of

different colors for your choose.

Crawler Parts Spare

28469-Receiver

(3Channel)

TR80227-Transmitter

(3Channel AM/FM27M/

40M-2.4G )

03019-Battery

( NI-MH 7.2V 3000mAh)

28424-Battery

(NI-CH 7.4V, 2200mAh)

180014-Front Gear Box

(Shell Only) AL.

180015-Rear Gear Box

(Shell only) AL.

180013-Gear Box(Shell only)

(AL.)

180016-Wheel Hex Mount

W/Pins (2*10 ) 4P

180021-Alum Wheel

Weight Set 150g 4P

Crawler Upgradable Optional

12

RK RKO3500-02 User manual

Popular Motorized Toy Car manuals by other brands