rlon become User manual

become
desk lamp
rlon

3
become is the geometry of an energetic system.
Both illuminant and interface are protagonists of a
geometric staging.
become tells one story of the journey to the center.
Of separation and oneness.
Of symmetry and tension.
become plays with gravitational ields.
It is a bridge from the outside to the inside.

5
congratulations
on your become desk lamp
This guide provides you with instructions on how to setup
and maintain your lamp as well as safety notes and legal
informations.

6
body
dimensions 270 x 290 x 240 mm
power supply
wattage < 36 w
voltage 220 v
cable length 2 m
illuminant
light ring T5 G10q
diameter of light ring 270 mm
wattage 32 w
light temperature 2700 k
luminous lux < 2400 lm
technical details

7
270 mm
290 mm
240 mm

8
instructions how to set up
and change the illuminant
The following instructions apply both for the irst setup of
the lamp and a later change of the illuminant.
Caution: Before installing and whenever changing
the illuminant, ensure that the power line is
disconnected!

9

10
Remove the metal ball from the body and put it
aside.
Turn the body of the lamp upside down and place
it on the edge of a table. Make sure the body is
slightly over the edge, so that the light ring will
not touch the table.
To avoid possible scratches on the body, put a
soft fabric or paper underneath the body.
1
make sure the lamp
is unplugged!

11
make sure the lamp
is unplugged!
2Open the two rear socket screws at the end of
the body with the provided socket screw key.
Remove the holding block.
Caution: Remove only the two rear socket screws
as shown in the drawing below.

12
Push the light ring from the top into the socket.
Caution: The become lamp only works with a t5
light ring with 27cm diameter and a g10q socket.
3

13
Make sure the four pins of the light ring have
connection and the ring sits smoothly in the
housing.
4

14
Attach the holding block again and ix it with the
two socket screws. Verify that that the light ring
sits in a 90 degree angle to the body.
5

15
Tighten the screws irmly, so that there is no gap
between the holding block and the body of the
lamp.
6

16
Turn over the lamp and connect the power line.
Position the metall ball on the ON position – in
the center of the light ring.
7

17
After irst setup and after each change of
illuminant, warm up the light ring by rotating the
dimmer knob fully to the right for one minute
before adjusting the desired brightness.
8

18
SAFETY NOTES AND LEGAL INFORMATIONS
WARNING!
The safety of this lamp can only be guaranteed if these instructions are observed,
during both installation and use. Please retain these safety instructions.
REMARKS
~ When installing and whenever changing the illuminant, ensure that the power supply
has been switched o.
~ The appliance may not be modiied or tampered with in another way than the one
necessary to change the illuminant.
~ Any other modiication may compromise safety causing the appliance to become
dangerous. rlon declines all responsibility for products that are modiied.
~ Should the external trailing cable get damaged, it must be replaced by rlon in order
to avoid any danger.
~ The product must be thrown out in a dierent manner than with the urban trashes.
CLEANING INSTRUCTIONS
Use only a soft cloth to clean the appliance, dampened with water and soap or alcohol
if needed for resistant dirt. Before cleaning the appliance, ensure that the power supply
has been switched o.
For any further questions regarding you product, please get in touch with us:
[email protected].

19
SICHERHEITSHINWEISE UND RECHTLICHE
INFORMATIONEN
ACHTUNG!
Wir garantieren nur dann für die Sicherheit der Leuchte, wenn diese Anweisungen
sowohl bei der Installation als auch beim Gebrauch genau beachtet werden. Bitte
bewahren Sie diese Anweisungen auf.
BEMERKUNGEN
~ Bei der Installation und beim Wechsel des Leuchtmittels ist sicherzustellen, daß die
Anlage vom Netz getrennt ist.
~ Der Apparat darf auf keinen Fall verändert oder anderweitig geönet werden, als zum
Wechsel des Leuchtmittels notwendig.
~ Jede Veränderung desselben kann die Sicherheit in Frage stellen und somit
gefährlich werden. rlon lehnt jede Verantwortung für unsachgemäß behandelte
Produkte ab.
~ Falls das lexible äußere Kabel beschädigt wird, muß es von rlon ersetzt werden, um
Gefahren zu vermeiden.
~ Das Produkt muss getrennt vom Stadtmüll entsorgt werden.
REINIGUNGSVORSCHRIFTEN
Bei der Reinigung der Leuchte bitte ausschließlich weiche Tücher verwenden und diese
mit Wasser und Seife oder etwas Alkohol anfeuchten. Stellen Sie vor jeder Reinigung
sicher, daß die Anlage vom Netz getrennt ist.
Für weitere Fragen zu Ihrem Produkt, kontaktieren Sie uns bitte unter
[email protected].

rlon GmbH
Lobeckstraße 3035
10969 Berlin
www.rlon.com