Rockwell Automation Sensia Jiskoot InSpec Remote I/O HUB Instruction manual

1
WJISKOOT™ MEASUREMENT SYSTEMS
InSpec Remote I/O HUB
(ATEX, IECEx)
Installation, Operation & Maintenance Manual
Manual No. H112, Rev. 2
MEASUREMENT

2

InSpec Remote I/O HUB (ATEX, IECEx)
3
Important Safety Information
Symbols used throughout the supporting documentation and on the products are defined below:
Symbol Meaning Definition
Dangerous Voltage To indicate hazards arising from dangerous voltages.
Warning/Caution An appropriate safety instruction should be followed or
caution to a potential hazard exists.
Protective Earth (Ground) To identify any terminal which is intended for connection to an
external conductor for protection against electric shock in
case of a fault, or the terminal of a protective earth (ground)
electrode.
Functional Earth To identify an earth (ground) terminal in cases where
Protective or clean Earth (ground) is explicitly required.
Frame or Chassis To identify a frame or chassis bonding terminal
Heavy This product is heavy and reference should be made to the
safety instructions for provisions of lifting and moving.
Static Sensitive Device
(Hand Prohibited)
All precautions against electro-static discharge (ESD) must
be observed to avoid damaging electronic circuits
-
Disposal:
Monitoring and Control Instruments, accessories and their packaging should be sorted for
environmental-friendly recycling.
Only for EC countries:
Do not dispose of Monitoring and Control Instruments into household waste! According to the
European Directive 2002/96/EC on waste electrical and electronic equipment (WEEE and its
incorporation into national law, Monitoring and Control Instruments that are no longer suitable for
use must be separately collected and sent for recovery in an environmental-friendly manner.
-
Tools Required:
Tools listed next to this symbol will be required to perform the task outlined in the text that
follows.
- Hints & Tips:
Text may help answer some questions or aid configuration.
Terms Used in This Manual
WARNING A warning identifies information about practices or circumstances that can lead to personal injury or
death, property damage, or economic loss.
CAUTION Caution statements Indicate actions or procedures which, if not performed correctly, may lead to
personal injury or incorrect function of the instrument or connected equipment.
Note Indicates additional information about specific conditions or circumstances that may affect instrument
operation.

InSpec Remote I/O HUB (ATEX, IECEx)
4
Table of Contents
Introduction................................................................................................................... 7
Model Number, Options & Marking............................................................................. 8
Marking (Label Detail) ......................................................................................................................................................... 9
Installation Details ...................................................................................................... 10
Enclosure Mounting, Orientation & Position ...................................................................................................................... 10
Lifting.......................................................................................................................................................................... 10
Orientation & Position................................................................................................................................................. 10
Wiring Methods & Materials .............................................................................................................................................. 11
Cable/Wire Selection......................................................................................................................................................... 11
Cable Entries..................................................................................................................................................................... 12
Field Connections....................................................................................................... 13
DIN Rail Terminals ............................................................................................................................................................ 13
Earthing Requirements ..................................................................................................................................................... 14
Shielded (Screened) Cables ............................................................................................................................................. 14
Power................................................................................................................................................................................ 14
Instrument Power ....................................................................................................................................................... 14
Ancillary Power (DC) .................................................................................................................................................. 15
Signals .............................................................................................................................................................................. 16
Relay Circuits (Outputs) ............................................................................................................................................. 16
RIO-DIO Module Connections (Digital I/O)................................................................................................................. 17
RIO-PUL Module Connections (Pulse Inputs) ............................................................................................................ 18
RIO-ANI Module Connections (Analogue Inputs) ....................................................................................................... 19
RIO-ANO Module Connections (Analogue Outputs) .................................................................................................. 20
Field cables (Intrinsically Safe).......................................................................................................................................... 21
Intrinsically Safe Apparatus Entity Parameters........................................................................................................... 21
: Putting into Service.................................................................................................. 23
Use ............................................................................................................................... 24
Adjustment & Calibration........................................................................................... 25
Safety Information ...................................................................................................... 26
Electrical Safety ................................................................................................................................................................ 26
Instrument Specifications.......................................................................................... 27
General Specifications ...................................................................................................................................................... 27
Compliance to INternational Standards............................................................................................................................. 28
Operation................................................................................................................... 29
Communications Failure ................................................................................................................................................... 29
Known States ............................................................................................................................................................. 29
Inspection & Maintenance ....................................................................................... 30
Health & Safety Precautions ............................................................................................................................................. 30

InSpec Remote I/O HUB (ATEX, IECEx)
5
Maintenance............................................................................................................................................................... 30
Annual Maintenance ......................................................................................................................................................... 30
Enclosure Screw/Bolts ...................................................................................................................................................... 30
Other .......................................................................................................................................................................... 31
: Product Specific Drawings .................................................................................... 32
: Troubleshooting ..................................................................................................... 33
Solving Common Problems............................................................................................................................................... 33
: Support.................................................................................................................... 34
Repackaging For Shipment............................................................................................................................................... 34
Spare Fuses...................................................................................................................................................................... 34
Other Spares..................................................................................................................................................................... 35
Abbreviations & Acronyms...................................................................................... 36
Abbreviations & Acronyms ................................................................................................................................................ 36
Appendix A: Publisher Notes ...................................................................................................... 39
Support.............................................................................................................................................................................. 39
Warranty............................................................................................................................................................................ 39
Disclaimer ......................................................................................................................................................................... 39
Contact us ......................................................................................................................................................................... 40
CERTIFIED PRODUCT
Scheduled Document
No modification permitted without reference to the
Notified Body
REVISION HISTORY
Revision: Description of change: Issuer: Approver: Date:
1 1st Issue MF TMM 31
st
October 2018
2 Change Document Branding to Sensia MF TMM 17
th
June 2020
*Mark of Sensia

6
GENERAL
WARNING!
This instrument is designed for connection to hazardous electric voltages.
Ignoring this warning can result in severe personal injury or mechanical damage.
To avoid the risk of electric shock and fire, the safety instructions of this manual must be
observed, and the guidelines followed.
The specifications must not be exceeded, and the unit must only be applied as described
in the following.
Prior to the installation and commissioning of the unit, this manual must be examined
carefully.
Only qualified personnel (technicians) should install this unit.
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
HAZARDOUS
VOLTAGE
CAUTION!
WARNING!
Until the instrument is fixed, do not connect hazardous voltages to the instrument.
The following operations should only be carried out on a disconnected unit and under
ESD-safe conditions: -
General mounting, connection and disconnection of wires.
Troubleshooting the unit.
Repair of the instrument must only be done by Sensia (UK) Ltd.
INSTALLATION
WARNING!
Installation may only be carried out by electrically skilled and instructed personnel in
accordance with national legislation, including the relevant standards.
All technical data on the instrument is to be observed.
Changes to the design and modifications to the equipment are not permitted.
The equipment shall only be operated as intended and only in undamaged and perfect
condition.
Sufficient segregation must exist between different cables and wires carrying different
types of signal or power and all other circuits.
All wires must be terminated, complete with crimping lugs. Unused cores should be
terminated to the earth bus bar.

InSpec Remote I/O HUB (ATEX, IECEx) Section 1: Introduction
7
Introduction
The Jiskoot™ InSpec* Remote I/O Hub is intended for use in hazardous locations in which an explosive gas
atmosphere, caused by mixtures of air and gases, vapour or mists, exist under normal atmospheric conditions, as
defined in IEC/EN 60079-0.
Under the ATEX directive, 2014/34/EU, the InSpec Remote I/O Hub is a Category II Group 2G piece of
equipment intended for use in a Potentially Explosive Gas Atmosphere, where the Area Classification is equal to
or hazard has been categorised as less than Zone 1 IIB+H2 T6 and the ambient temperature range Tamb or Ta =
-20°C to +50°C or + 60°C (depending upon the model).
Depending on the application software installed, the unit may be used for sampling, blending or wildstream
control applications.
The unit may be sold separately or as part of a system for integration into a larger installation.
Depending on the model purchased, the following functions may be integrated into the unit:
Load-Cell Amplifiers (2 off) to interface with a Jiskoot CanWeigh System
Isolating Converter (1 or 2 off) to interface with Jiskoot CanHigh System
Ancillary power for 24V DC solenoid coils and transmitters.
Ethernet Line Driver Interface for applications that have a distance exceeding 100 metres between the
Remote I/O Hub and the nearest Ethernet Switch/Router.
Maximum of 4 Solid State Relays (SSR) suitable for switching either AC or DC circuits, up to 1 Amp,
depending upon model.
Maximum of 4 RIO Modules, from the following:
oJiskoot RIO-DIO Digital Input/Output Module(s)
oJiskoot RIO-PUL Pulse/Frequency Input Module(s)
oJiskoot RIO-ANI 4-20mA Analogue Input Module(s)
oJiskoot RIO-ANO 4-20mA Analogue Output Module(s)
NOTE: When requesting assistance or spare parts, please provide the model and serial number of the unit to
ensure that the correct options are noted.

Section 2: Model Number, Options & Marking InSpec Remote I/O HUB (ATEX, IECEx)
8
Model Number, Options & Marking
Each Jiskoot InSpec Remote I/O Hub has a model number that identifies the options fitted, as per the following
table:
CODE DESCRIPTION
Cable Entries:
A Metric threads
B Imperial threads
Certification:
A ATEX (Europe), IECEx
E ETL-Listed (USA & Canada)
AC/DC PSUs:
X None fitted
A
Ancillary AC-DC PSU
(Module & Transmitter Power)
B
Ancillary AC-DC PSU
Solenoid Power
C Both Module & Ancillary Power
Relays:
X None
0 to F AC or DC Output (Encoded)
Remote I/O Modules (4 max.):
DIO: 0 to 4 PUL: 0 to 2
A
NI: 0 to 4
A
NO: 0 to 2
RIO-DIO Qty.
RIO-PUL Qty.
RIO-ANI Qty.
RIO-ANO Qty.
Ethernet Interface:
A Cable/Wire Only
B Ethernet Extender
CanWeigh/CanHigh:
X None
3 2 Ch. CanWeigh Amplifiers (2 x D5264S)
4 2 Ch. CanHigh Interface (1 x D5030D)
5 4 Ch. CanHigh Interface (2 x D5030D)

InSpec Remote I/O HUB (ATEX, IECEx) Section 2: Model Number, Options & Marking
9
MARKING (LABEL DETAIL)
LABEL DETAIL APPLICATION
AC powered unit.
With Intrinsically Safe Isolators.
Model Numbers
##A######3##B######3
##A######4##B######4
##A######5##B######5
##C######3
##C######4
##C######5
AC powered unit.
Without Intrinsically Safe Isolators.
Model Numbers
##A######X
##B######X
##C######X
DC powered unit.
With Intrinsically Safe Isolators.
Model Numbers
##X######3
##X######4
##X######5
DC powered unit.
Without Intrinsically Safe Isolators.
Model Numbers
##X######X
##X######X
##X######X

Section 3: Installation Details InSpec Remote I/O HUB (ATEX, IECEx)
10
Installation Details
Installation may only be carried out by skilled electricians and instructed personnel in accordance with local
statutory, regulatory requirements for the country of use and customer requirements.
The equipment must not be installed into, or operated in, Hazardous (Classified) Locations outside the scope of
those stated in the previous section of this manual. The enclosure must not be installed or operated in a Zone 0
Hazardous Location.
All technical data on the enclosure is to be observed.
Changes to the design and modifications to the equipment are not permitted.
The electrical installation must be in accordance with applicable national standards (equivalent to IEC/EN 60364)
in addition to the requirements for installation in hazardous areas according to EN/IEC 60079-14 "Electrical
installations in hazardous locations" or equivalent national standards.
The equipment is intended for permanent connection. The product is to be suitably grounded or earthed. For
additional information, refer to Earthing Requirements.
A double pole isolator, having suitable safety approvals for the country of the equipment’s ultimate end use t,
must be installed to disconnect the equipment from the supply. It must be located nearby, easily reached and
marked as the disconnecting device for the equipment.
ENCLOSURE MOUNTING, ORIENTATION & POSITION
LIFTING
CAUTION
This equipment weighs approximately 50 kg (110 lb). A detailed hazard analysis/risk
assessment should be performed before attempting to lift and secure the enclosure into
position.
The instrument shall be securely mounted to a suitable vertical flat surface using all four
mounting lugs/feet cast onto the enclosure, with M12 (½ inch) mounting bolts and
washers.
Depending upon the access limitations, the equipment should be lifted using mechanical
lifting aids such as a forklift, or an overhead crane with a suitably rated nylon strop
around the body of the housing.
Care must be taken to avoid damaging the threaded entries in the bottom of the
enclosure and the flame path.
When lifting aids cannot be used, the equipment should be put into position using a team lift
employing a minimum of 3 persons.
ORIENTATION & POSITION
The unit shall be mounted so that all cable entries are at the bottom of the enclosure.
Once installed, a minimum separation of 40mm (1.57 in.) is required and shall be maintained between
the flameproof flange joint and any solid object that is not part of the enclosure.
The location should not subject the controller to vibration or shock.
Sunshades are recommended in hot and sunny environments where temperatures exceed 30°C (86°F).

InSpec Remote I/O HUB (ATEX, IECEx) Section 3: Installation Details
11
WIRING METHODS & MATERIALS
The electrical installation must be in accordance with applicable national standards (equivalent to IEC/EN
60364) in addition to the requirements for installation in hazardous areas according to IEC/EN 60079-14
"Electrical installations in hazardous locations" or equivalent national standards. Local wiring ordinances may
also apply.
Only personnel who are experienced with field wiring should perform these procedures.
Personnel installing field wiring must strictly adhere to all manufacturers datasheets and
instructions.
The conduit or cable gland threads must be the same thread size as the enclosure’s entry thread
size, either M25 & M20, or 1” and ¾” NPT, as determined by the model number – See Section 2:.
Cable glands
oA barrier gland is required due to the volume of the enclosure.
oCable glands must be used with an appropriate cable, as per the manufacturer’s
specifications, to maintain integrity of the installation.
oThe cable must be adequately supported.
All wires must be terminated, complete with crimping lugs.
Terminal block screws must be tightened to a torque of 4.4 to 5.3 lb.in.
The hazardous area end of any unused cores shall be either a) connected to earth or b) adequately
insulated by means of suitable terminations (Insulation tape alone is not recommended) and
connected to earth in the non-hazardous area.
CABLE/WIRE SELECTION
All field wiring must have a minimum specification of 0.5mm², 75°C, VW-1. It must be suitably sized for the
application and local conditions, conform to national standards (equivalent to IEC/EN 60364) in addition to the
requirements for installation in hazardous areas according to IEC/EN 60079-14 "Electrical installations in
hazardous locations" or equivalent national standards. Local wiring ordinances may also apply.
Considerations such as (but not limited to) the supply voltage and frequency, load current, voltage drop,
temperature, cable mounting and grouping factors should be considered.
In general, Sensia recommends the following types of cables for the associated signal types:
Analogue Signals : Screened twisted pairs with an overall screen.
Blue cable sheath for Intrinsically Safe circuits.
Pulse/Frequency Signals : Screened twisted pairs with an overall screen.
Blue cable sheath for Intrinsically Safe circuits.
DC Digital Signals : Multicore with an overall screen

Section 3: Installation Details InSpec Remote I/O HUB (ATEX, IECEx)
12
CABLE ENTRIES
All entries must be fitted with certified and correctly dimensioned gland, equal to the marking on the enclosure (II
2 G Ex db IIB +H2 Gb) or better. For additional information on the applicable standards, refer to IEC/EN
60079-14.
All unused entries must be fitted with certified flameproof blanking elements, equal to the marking on the
enclosure (II 2 G Ex db IIB +H2 Gb) or better. A blanking element shall not be used with an adapter
Each entry shall have no more than one certified flameproof thread adapter, equal to the marking on the
enclosure (II 2 G Ex db IIB +H2 Gb) or better when a thread adapter is used.
When changing the size of an entry, this should be documented and marked accordingly per IEC/EN 60079-1
clause 13.2 marking of the specific thread type and size adjacent to the hole in accordance with table 15.
Intrinsically safe circuits must be installed into the two right hand entries, in the bottom of the enclosure. Once the
circuits are brought into the enclosure, they must remain physically and electrically isolated from any other
circuits within the enclosure.
No Intrinsically Safe Earth is required as only isolated barriers are used in the unit.
MODEL
NUMBER
(REF. ABOVE
IMAGE) SIZE ‘A’ SIZE ‘B’
A######### Metric Threads M20 M25
B######### Imperial Threads ¾” 1”
Reserved for Intrinsically Safe
Circuits

InSpec Remote I/O HUB (ATEX, IECEx) Section 4: Field Connections
13
Field Connections
DIN RAIL TERMINALS
TERMINALS FUSE CROSS REFERENCE OPTION NOTES
E Protective Earth (PE) connection point
1 Section 4:
AC Power Supply Connection Yes Internal AC to DC PSU(s) AC Input Power
F1 F1
F2 F2
Yes
AC Output (fused) for AC SSR loads
2
Additional Neutral Connections
3
4
5
E Section 4:
Earthing Requirements Protective Earth (PE) connection point
13
Section 4:
Relay Circuits (Outputs) Yes
Relay Output No. 1
14
13 Relay Output No. 2
14
13 Relay Output No. 3
14
13 Relay Output No. 4
14
E Section 4:
Earthing Requirements Protective Earth (PE) connection point
6
Yes Additional 0V DC (GND) Connections
for DC SSR Loads
7
8
9
F3 F3 Section 4:
Ancillary Power (DC) Yes +24V DC 32W Output for DC SSR Loads
F4 F4 Section 4:
DC Power Supply Connection
&
Ancillary Power (DC)
Yes
RIO-Hub +24V DC Input Power (30W
max.), or +24V DC Output (12W
max.)
9 0V DC (GND) Connection
E Section 4: Earthing Requirements Protective Earth (PE) connection point

Section 4: Field Connections InSpec Remote I/O HUB (ATEX, IECEx)
14
EARTHING REQUIREMENTS
An external protective earth (PE) conductor, associated with unit’s main power source, must be
connected to the dedicated PE terminal. The minimum size of the incoming external earth wire is 2.5mm²
(14 AWG) and rated for 300V, 105°C, VW-1.
There is provision for making an external earth connection to the enclosure, via an external grounding
screw.
SHIELDED (SCREENED) CABLES
Control and signal cable screens and drain wires should be terminated to a low-impedance earth (ground),
preferably using a 360° shield (screen) clamp. If pigtails are used, where the screen is brought down to a single
wire and connected to the earth point, these must be as short as possible; otherwise the inductance of the pigtail
renders it useless at high frequencies.
For a circuit with an ungrounded source the screen should be terminated at the input end, whereas if the
input is floating and the source is grounded then the screen should be terminated at the source end.
If both the signal source and signal inputs are both grounded, terminating the screen at both ends is not
recommended as this may reduce the performance of the system.
To shield against low-frequency electric fields terminate the screen at one end only.
To shield against low-frequency magnetic fields terminate both ends of the screen.
POWER
INSTRUMENT POWER
The instrument can be supplied for use with either AC or DC power. The instructions below describe the wiring
connections for each power supply type.
Do not attempt to power the instrument from both AC and DC supplies at the same time!
A double-pole isolator, having suitable safety approvals for the country of the equipment’s end
use, must be installed to disconnect the equipment from the supply. It must be located nearby
and easily reached; and marked as the disconnecting device for the equipment.
AC Power Supply Connection - Model Numbers ##A#######
##B#######
##C#######
AC power is connected to the unit via terminals E, N, and F1.
TERMINAL FUSE DUTY
E Protective Earth
N Neutral
F1 F1 Live
Ensure that the associated supply fuse or circuit breaker and cabling is suitably sized.

InSpec Remote I/O HUB (ATEX, IECEx) Section 4: Field Connections
15
DC Power Supply Connection - Model Numbers ##X#######
DC power is connected to the unit via terminals F4, 10 and E.
TERMINAL FUSE DUTY
F4 F4 +24VDC
10 GND (0V DC)
E Protective Earth
Ensure that the associated supply fuse or circuit breaker and cabling are suitably sized.
ANCILLARY POWER (DC)
24VDC (32 Watts max.) - Model Numbers ##B#######
##C#######
An optional AC/DC PSU intended to supply equipment such as solenoid coils.
TERMINAL FUSE DUTY
F3 F3 +24V DC (32 Watts Max. Continuous Load)
6, 7, 8 & 9 GND (0V DC)
24VDC (12 Watts) - Model Numbers ##A#######
##C#######
An optional AC/DC PSU intended to supply equipment such as temperature, flow or pressure
transducers.
TERMINAL FUSE DUTY
F4 F4 +24V DC (12 Watts Max. Continuous Load)
10 GND (0V DC)

Section 4: Field Connections InSpec Remote I/O HUB (ATEX, IECEx)
16
SIGNALS
Safety Extra Low Voltage (SELV) Circuits
Connect only SELV circuits to the RIO-DIO, RIO-PUL, RIO-ANI or RIO-ANO modules.
RELAY CIRCUITS (OUTPUTS)
The Remote I/O Hub requires different relay modules to switch AC and DC loads. Please
check carefully that the load voltage matches the relay type fitted.
Crydom # CN024D24 = 24V DC Load Voltage @ 1 Amp Max.
Crydom # CN240A24 = 100-240V AC Load Voltage (50/60Hz) @ 1 Amp Max.
Relay Output / Load Relay Output / Load
Model RL1 RL2 RL3 RL4 Model RL1 RL2 RL3 RL4
###0###### AC AC AC AC
###8###### DC AC AC AC
###1###### AC AC AC DC
###9###### DC AC AC DC
###2###### AC AC DC AC
###A###### DC AC DC AC
###3###### AC AC DC DC
###B###### DC AC DC DC
###4###### AC DC AC AC
###C###### DC DC AC AC
###5###### AC DC AC DC
###D###### DC DC AC DC
###6###### AC DC DC AC
###E###### DC DC DC AC
###7###### AC DC DC DC
###F###### DC DC DC DC
###X###### No relays fitted
Terminals 11 (13+) and 14 on each relay (RL1, RL2, RL3 & RL4) provide connections to the relays outputs,
controlled via the first RIO-DIO module, as follows:
Terminal Duty
AC DC
11 (13+) +
14 -
The relay outputs can switch circuits designated as Installation Category III. Each relay output may switch a
maximum of 250VAC rms or 30VDC and is rated for 1 Amp resistive or inductive load at 60°C (140°F). All wiring
connected to any relay output must have a suitably sized protection device fitted to protect the relay circuit and
load being switched by it.
11
14
Fuse
1, 2, 3 or 4
AC LOAD
F2
AC Relay
Output
11
14
Fuse
5, 6, 7 or 8
DC LOAD
F3
DC Relay
Output

InSpec Remote I/O HUB (ATEX, IECEx) Section 4: Field Connections
17
RIO-DIO MODULE CONNECTIONS
(
DIGITAL I/O
)
Model Numbers:
####1#####
####2#####
####3#####
####4#####
IMPORTANT: Cables terminating to this terminal block must be screened.
For complete information about the RIO-DIO module, please refer to the InSpec Remote I/O Module manual. The
main field terminal assignments are as follows:
RIO-DIO MODULE
(FIELD CONNECTIONS)
TERMINAL DUTY
1
+24VDC Common Connection Points
(From External PSU)
2
3
4
5 Digital I/O Point # 1
6 Digital I/O Point # 2
7 Digital I/O Point # 3
8 Digital I/O Point # 4
9 Digital I/O Point # 5
10 Digital I/O Point # 6
11 Digital I/O Point # 7
12 Digital I/O Point # 8
13
0V DC Common Connection Points
14
15
16

Section 4: Field Connections InSpec Remote I/O HUB (ATEX, IECEx)
18
RIO-PUL MODULE CONNECTIONS
(
PULSE INPUTS
)
Model Numbers:
#####1####
#####2####
#####3####
#####4####
IMPORTANT: Cables terminating into Pulse Inputs must be screened and kept separate from the Digital I/O.
For complete information about the RIO-PUL module, please refer to the InSpec Remote I/O Module manual.
The main field terminal assignments are as follows:
RIO-PUL MODULE
(FIELD CONNECTIONS)
TERMINAL DUTY
1 + Ch. # 1 Pulse/Frequency Input
2 -
3 + Ch. # 2 Pulse/Frequency Input
4 -
5 + Ch. # 3 Pulse/Frequency Input
6 -
7 + Ch. # 4 Pulse/Frequency Input
8 -
9 + Ch. # 5 Pulse/Frequency Input
10 -
11 + Ch. # 6 Pulse/Frequency Input
12 -
13 + Ch. # 7 Pulse/Frequency Input
14 -
15 + Ch. # 8 Pulse/Frequency Input
16 -

InSpec Remote I/O HUB (ATEX, IECEx) Section 4: Field Connections
19
RIO-ANI MODULE CONNECTIONS
(
ANALOGUE INPUTS
)
Model Numbers:
######1###
######2###
######3###
######4###
IMPORTANT: Cables terminating into Analogue Inputs must be screened and kept separate from the Digital I/O
and Pulse Inputs.
For complete information about the RIO-ANI module, please refer to the InSpec Remote I/O Module manual. The
main field terminal assignments are as follows:
RIO-ANI MODULE
(FIELD CONNECTIONS)
TERMINAL DUTY
1 + Ch. # 1 Analogue Input
(4-20mA)
2 -
3 + Ch. # 2 Analogue Input
(4-20mA)
4 -
5 + Ch. # 3 Analogue Input
(4-20mA)
6 -
7 + Ch. # 4 Analogue Input
(4-20mA)
8 -
9 + Ch. # 5 Analogue Input
(4-20mA)
10 -
11 + Ch. # 6 Analogue Input
(4-20mA)
12 -
13 + Ch. # 7 Analogue Input
(4-20mA)
14 -
15 + Ch. # 8 Analogue Input
(4-20mA)
16 -

Section 4: Field Connections InSpec Remote I/O HUB (ATEX, IECEx)
20
RIO-ANO MODULE CONNECTIONS
(
ANALOGUE OUTPUTS
)
Model Numbers:
#######1##
#######2##
#######3##
#######4##
IMPORTANT: Cables terminating into Analogue Outputs must be screened and kept separate from the Digital I/O
and Pulse Inputs.
For complete information about the RIO-ANO module, please refer to the InSpec Remote I/O Module manual.
The main field terminal assignments are as follows:
RIO-ANO MODULE
(FIELD CONNECTIONS)
TERMINAL DUTY
1 + Ch. # 1 Analogue Output
(4-20mA)
2 -
3 + Ch. # 2 Analogue Output
(4-20mA)
4 -
5 + Ch. # 3 Analogue Output
(4-20mA)
6 -
7 + Ch. # 4 Analogue Output
(4-20mA)
8 -
9 + Ch. # 5 Analogue Output
(4-20mA)
10 -
11 + Ch. # 6 Analogue Output
(4-20mA)
12 -
13 + Ch. # 7 Analogue Output
(4-20mA)
14 -
15 + Ch. # 8 Analogue Output
(4-20mA)
16 -