
Reprint by Rocky Americas Inc. [www.RockyAmericas.com]
Copyright © 2008-2012 All Rights Reserved. [MO136CW087CS4102_3Camera_Instruction.pdf - Page 1]
A. 22-pin Power A/V
Cable
B. Front Panel A/V Input
Cable
C. Standard Mount Bracket
D. Universal Mount
Bracket
E. Sun Shield
MO136CW087CS4012 Quick
Connection – Three-Camera Sy tem
F. Remote Control
G. Angle Adjust Screws
H. (2) 4-pin Camera Power
A/V to RCA
Adapter/Connector
I. (2) 15 Feet 4-pin
Camera Connecting
Extension Cable
J. (1) 30 Feet 4-pin
Camera Connecting
Extension Cable
Your y tem might not come with all elective acce orie hown above. Picture are for demon tration purpo e only; actual look may vary.
Quick Connection In truction (Please refer to accessories above the connection diagram on next page and Operating Instructions Manual.)
1. Connect the 22-pin cable socket coming out of the monitor to the “22-pin power
A/V cable” (part A). Note the engraved arrows on the sockets from both ends
should be aligned (same for all socket connections).
2. Connect the single red color wire (marked with “VCC” tag) for positive power
supply; connect the single black color wire (marked with “GND” tag) for ground.
3. (Step 3-5 for connecting the rear view camera) Connect the single brown
colored wire (marked with “CAMERA B TRIGGER” tag) to the positive wire of
vehicle’s reverse circuit or backup light circuit. (For auto camera activation when
vehicle in reverse mode function only skip if the function is not preferred.)
4. Connect the brown color 4-pin socket (marked with “CAMERA BACK” tag) to the
female end of a “30 feet 4-pin camera connecting extension cable” (part J);
Connect the other end of the 30-feet extension cable to the female 4-pin socket
of the “4-pin camera power A/V to RCA adapter/connector” (part H). (Note if
you purchased additional extension cable connect it to the first 30-feet extension
cable before connecting to the 4-pin camera adapter.)
5. Connect the yellow RCA video socket the white RCA audio socket (skip if your
camera dos not have audio capability or audio is not needed) and the power
socket of the “4-pin camera power A/V to RCA adapter/connector” (part H) to
the rear view camera’s yellow RCA video socket the white RCA audio socket
(skip if your camera does not have audio capability) and the power socket.
6. (Step 6-8 for connecting the left ide view camera) Connect the single
white colored wire (marked with “CAMERA L TRIGGER” tag) to the positive wire
of vehicle’s left turn signal light circuit. (For auto camera activation with left turn
signal light function only skip if the function is not preferred.)
7. Connect the white color 4-pin socket (marked with “CAMERA LEFT” tag) to the
female end of a “15 feet 4-pin camera connecting extension cable” (part I);
Connect the other end of the 15-feet extension cable to the female 4-pin socket
of the “4-pin camera power A/V to RCA adapter/connector” (part H).
8. Connect the yellow RCA video socket and the power socket of the “4-pin camera
power A/V to RCA adapter/connector” (part H) to the first side view camera’s
yellow RCA video socket and the power socket.
9. (Step 9-11 for connecting the right ide view camera) Connect the single
blue colored wire (marked with “CAMERA R TRIGGER” tag) to the positive wire of
vehicle’s right turn signal light circuit. (For auto camera activation with right turn
signal light function only skip if the function is not preferred.)
10. Connect the blue color 4-pin socket (marked with “CAMERA RIGHT” tag) to the
female end of a “15 feet 4-pin camera connecting extension cable” (part I);
Connect the other end of the 15-feet extension cable to the female 4-pin socket
of the “4-pin camera power A/V to RCA adapter/connector” (part H).
11. Connect the yellow RCA video socket and the power socket of the “4-pin camera
power A/V to RCA adapter/connector” (part H) to the second side view camera’s
yellow RCA video socket and the power socket.
12. Please properly preserve other cables wires sockets for future upgrades.