User’s ManualAlcar®H51
8
Note:
1) After arming the first 5s. are reserved for supplemental commands such as:
2) Manual sensors bypass by remote control (the proximity sensor, the shock sensor and the
ultrasonic sensor);
3) Silent alarm enabling (the siren is disabled);
4) System disarming can only be made after the 5s after arming command;
5) If the parameter 11 - Door contacts delay when arming is enabled, then the doors pin-switches
are tested only after delay duration estabilished by parameter 12. If, the delay duration is over and
the system detects at least one opened door, it will warn by three optical-acoustical signals and it
will bypass the respective input during arming.
6) If afterwards all the doors are closed, the respective input becomes active again, after sensors
stabilization delay (20s after arming).
Arming/disarming silent
When no acoustical confirmation is needed, press the button 1 for about 2s instead of the short
press described before (0.5s). All the signals will become silent, meaning that the optical confirma-
tion only will remain active for respective arming/disarming period (warning for reverse car moving,
for door open, for arming with position lights turned ON, for silent siren, for sensors bypassing by
remote control, for doors, hood and trunck bypassing, for faulted sensors disabling when arming).
Remote controlled bypassing the sensors
Remote controlled bypassing the sensors can only be made during the first 5s after the
arming command. The bypass order is: proximity sensor -> shock sensor -> ultrasonic
sensor.
If the button 1 of the remote control is pressed, the system bypasses respective sensor, confirms
by an optical-acoustic or optical signal (depending on arming mode) and advances to the next
sensor.
If the button 2 of the remote control is pressed, the system doest bypass the sensor, but it
advances to the next sensor and confirms by optical-acoustic or optical signal.
Sensors bypass is only available for that respective arming period. When disarming the system the
bypass is disabled.
Example: If one wishes to bypass the shock sensor only it will proceed as follows:
1. During the first 5s after the arming command press button 2 to advance at the shock sensor
without bypassing the proximity sensor. The system confirms by an optical-acoustical signal (or
just optical if the arming was silent).
2. Press button 1 to bypass the shock sensor. The system confirms by an optical-acoustical
signal (or just optical if the arming was silent).
3. Press button 2 for not bypassing the ultrasonic sensor. If the button 2 is pressed the system
confirms by an optical-acoustical signal (or just optical if the arming was silent).
Arming with silent alarm
If the owner dos not want the theft to be warned, then the system can be armed with silent alarm
(the siren is disabled). The using of this function is needed when the system has a pager. The alarm
state will be notified on page and flashing lights only, according to the value of parameter 9.
The silent alarm function can only be activated within the first 5s after the arming command,
9
by simultaneously pressing both remote control buttons. The function is active during that
specific arming period only. The function enabling is confirmed by 2 optical-acoustic signals (or only
optical signals for silent arming). When disarming the system, the function is disabled.
Car finding
In order to locate the car in a full parking area, press shortly (0.5s) the button 2. Five optical and
acoustical signals will be provided. The signals will be:
- short if no alarm was reported meanwhile;
- long if there was an alarm since the system was armed
This function is active with the system armed only.
NOTE!
The car finding function is not active during the reserved 5s after the arming command.
If the button 2 is pressed during the first 5s after arming this command will be interpreteted
according to sensors disabling by remote control procedure.
Panic
In case of emergency, pressing shortly (0.5s) and simultaneously the two buttons of a
remote control can trigger the alarm. The siren will sound continuously, the pager will emit the
alarm signal (if there is provided a pager, which is optional) and the flashing lights will flash for
three minutes.
This function is used to discourage a potential burglar, and to draw the attention towards the
vehicle.
The function is enabled no matter of the systems state (armed/disarmed), except the first 5s after
arming and can be stopped during the thre minutes by pressing shortly any of the buttons.
NOTE!
If the both buttons of the remote are pressed simultaneously during the first 5s after arming, the
silent alarm function will be enabled (during respective arming period the siren will be disabled).
The silent alarm function enabling will be confirmed by 2 optical-acoustic signals (or optical signals,
depending on arming mode).
Signalling the remote controls number
The hopping code remote controls of ALCAR®-51, are learnt by the central unit through the
procedure described in chapter 5.1 Learning/clearing remote controls. The remote controls
number, recorded in central units memory (up to 4), can be notified by a simple short press of
button 2 while in disarmed mode. The system answers by a number of optical-acoustical
signals (or optical only if the system was disarmed silent) equal to the remote controls number.
Note!
1) While disarmed, when the engine is turned off, pressing long (more than 2s.) the button 2
will activate the trunk release output;
2) While disarmed, when the engine is turned on, if parameter 13 (anti-car jacking) is
enabled, by pressing long (more than 2s.) the button 2 will enter the anti-car jacking mode.
Anti-carjacking mode
The function is necessary in the case when the burglar threats the owner and takes the car in its
presence, with the key in contact. Once the function is triggered, the car will stop after 1min. and
will enter the anti-carjacking alarm mode..
