Rohnson R-1030 User manual

Electric Shaver
Operation instructions
MODEL: R-1030
Before operating this unit, please read the instructions completely and save them.

Thank you for purchasing the Rohnson wet/dry shaver.
Before operating this unit, please read these instructions completely; please keep
the manual ready for reference.
Caution
1. Do not charge the shaver when the temperature is below 0℃(32°F) or above
40℃(104°F), where it will be exposed to direct sunlight or a heat source, or
where is a lot of moisture.
2. Please put the protective cap on the shaver every time to prevent cap damage. To
avoid personal injury, do not use the shaver if it has a damaged cap or inner
cutter.
3. Clean the device and especially the inner parts of the shaving head regularly in
order to maintain your shavers cutting performance.
4. Wash the shaver in tap water. Do not use salt water or boiling water. Also, do not
use cleaning products that are designed for toilets, bathrooms or kitchen
appliances. Do not submerge the shaver for a long time.
5. If the shaver is not working properly, have it inspected at the place of purchase or
an authorized service center.
6. Always use your shaver for its intended use, as described in this manual.
7. Please make sure that the old batteries are disposed of at an officially assigned
location.
8. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and maintenance shall not be made by
children without supervision.
9. Children should be supervised to ensure that they do not play with the appliance.
10. Suitable for cleaning under an open water tap.
11. WARNING: Detach the hand-held part from the supply cord before cleaning it in
water.
12. Please keep the manual handy for reference.
13. Use only with the supplied adaptor

Before use
Your wet/dry shaver require a little time to get used to because your skin and beard
need about a month to adjust to any new shaving method.
Parts identification (see fig. 1)
①Protective cap
②Foil frame
③Shaving head floating system
A -a. Shaving cap
b. Shaving head
B-Floating frame
④Release knob of floating system
⑤Hair chamber
⑥Charging indicator light
⑦Switch
⑧Trimmer
⑨Trimmer handle

⑩Charging socket
⑪Adaptor
⑫Washable sign
⑬Cleaning brush
Using your shaver (see fig.2)
1. Remove the protective cap.
2. Press the switch to turn the shaver on.
3. Move the shaver quickly over your skin and against the growing direction of beard.
Make both straight and circular movements.
4.Press the switch to turn the shaver off.
5. Put the protective cap on the shaver every time you have used to prevent damage
of shaving cap. Slide the trimmer knob up to open the trimmer, Place the trimmer at
a right angle (90°) to your skin and move it downward to trim sideburns.
Cleaning and maintenance (see fig. 3,4,5,6)
1. For the purpose of good cleanness to the saver. It’s recommended that you clean your shaver
with water and regular cleaning will keep your shaver in good condition while preventing
odors or bacteria from developing and maintain the cutting performance.
2. Switch off the shaver.
3. Push the foil release button and remove the foil frame. Turn the inner rack switch
anticlockwise and remove out the inner cutter.
4. Clean the guard, foil frame, hair chamber and the shaver body with the long side of brush.
Clean the inner cutter with the short side of brush.
5. Reassemble the shaver parts in the reverse order.
The cutting system maintenance (see fig.4,5)
It is recommended to clean the device and especially the inner parts of the shaving
head regularly in order to maintain your shavers cutting performance.
1. Press down foil-frame release button and open the bracket.
2. Take apart floating system from the bracket via release knob of floating systems
fig.4. Rotate cap-fixing frame to certain locating as fig5 than take shaving cap and
shaving head outside.
3. Reassemble the shaver parts in the reverse order.
Charge (see fig.7)
Charge about two hours, after full charge the red light turns green light shows.
Recycling the battery (see fig.8)
Batteries contain substances that may pollute the environment. The battery in this
Warning-To prevent electric shock or personal injury, disconnect the
power cord from the shaver and turn off the shaver before cleaning.

shaver is not intended to be replaced by consumers. However, the batteries may be
replaced at an authorized service center.
Technical specifications
Model No.: R-1030
Adapter input: 100-240V~ 50Hz
Motor voltage: 3.2V
Rated power：5VDC 1A
Charging time: 2 hours
This product is intended for household use only
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC
DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban waste. It must be
taken to a special local authority differentiated waste collection centre or to a dealer providing
this service. Disposing of a household appliance separately avoids possible negative
consequences for the environment and health, deriving form inappropriate disposal and enables
the constituent materials to be recovered to obtain significant savings in energy and resources.
As a reminder of the need to dispose of household appliances separately, the product is marked
with a crossed-out wheeled dustbin.