Roketa RTQ-260w User manual

RTQ-260w
Instruction for the installation

STEP 1：INSTALL HANDLE BAR
PART NAME QTY SPEC. REMARK PART NAME QTY SPEC. REMARK
①HANDLEBAR
HOLDER 1 On ATV ④ clamp 2 ATTACHMENT
②handlebar 1 On ATV ⑤clamp holder 2 ATTACHMENT
③bolt 4 M8×60 attachment
Install step:
1.put⑤on①.
2. Put on②⑤，clamp by④. ① ③ ④ ⑤ ②
1. Fasten④②⑤on①by ③
REMARK：Clamp④⑤on②’spline tooth

STEP 2：INSTALL MAIN LAMPAND LAMPSHADE
PART NAME QTY SPEC. REMARK PART NAME QTY SPEC. REMARK
①SCREW 2 ON MAIN LAMP ⑨INSERT OF ODOMETER
INDICATION
1 Four hole On main
lampshade
②TOP COVER 1 ON MAIN LAMP ⑩INSERT OF SWITCH OF POWER 1 Six holes On main
lampshade
③BRACKET OF MAIN
LAMP 1
ON ATV ⑾INSERT OF ODOMETER’S POWER
IN MAIN THREADS
1 Two
holes
On ATV
④MAIN LAMPSHADE 1 ON MAIN LAMP ⑿INSERT OF POWER MAIN LAMP IN
MAIN THREADS
1 Four
holes
ON ATV
⑤SCREW 2 M8×20 ON MAIN
LAMPHOLDER
⒀INSERT OF ODOMETER
INDICATIONIN MAIN THREADS
1 Four
holes
ON ATV
⑥ MAIN LAMP HOLDER 1 ON HANDLE BAR
HOLDER
⒁INSERT OF POWER SWITCH IN
MAIN THREADS
1 Six holes ON ATV
⑦INSERT OF
ODOMETER
1 TWO
HOLES ON MAIN
LAMPSHADE
⒂MAIN LAMP 1 ON ATV
⑧INSERT OF MAIN
LAMP
1 FOUR
HOLES
ON MAIN
LAMPSHADE
INSTALL STEP :1.TAKE①DOWN FROM ⒂ 2.TAKE②③④OFF。3.TAKE⑸DOWN FROM⑹4.FASTEN⑶ ON ⑹BY⑸ THROUGH
THE INSTALLATION HOLE.5.REINSTALL⑵⑷ON⑶（PUT⑷POTHOOK HANG INTO②HOLE）FIX BY⑴。6. CONNECT THE THREADS；
CONNECT⑦AND⑾、CONNECT⑧AND⑿、CONNECT⑨AND⒀、CONNECT⑩AND⒁。
REMARK：SURE CONNECT FASTNESS !!!!

①② hang hole hole of installation ③
⒂ ④ pothook ⑤ ⑥
⑦⑧ ⑨ ⑩ ⒀ ⑾⑿⒁

STEP 3：INSTALL FRONT WHEEL
○
3
INSTALL STEP：
2. Take②off③②
3. Install①on○
3 then fix by ○ 2 and fasten.
Remark：valve must be in forth，○
2 prick is in ○ 3 ’way, right and left ○ 2is
balanceable.
①
PART NAME QTY. SPEC. REMARK
①FRONT WHEEL 2
23*7-10
INSIDE CARTON
②NUT 8 M10 See ○ 3
○
3 trig hub 1 On the ATV

STEP 4：INSTALL REAR SHOCK ABSORBER
PARTS NAME QTY SPEC. REMARK
①rear shock absorber 1 On the ATV
②bolt 1 M12×80 On ⑤
③nut 1 M12 On ⑤
④pin 1 On ⑤
⑤REAR SHOCK
ABSORBER HOLDER 1 On the ATV
INSTALLSTEP:
1. TAKE AWAY②③④FROM⑤
2. Put①inside⑤ ① ③ ④
3. From left to right to connect on ⑤ then fasten ① by ②
4. stall④on②and detach.
⑤ ②

STEP 5：INSTALL BATTERY
PART NAME QTY SPEC. REMARK
①ELECTROLYTE 1 In box of battery
②FILLER 1 In box of battery
③RUBBER PLUG 1 In box of battery
④BATTERY 1 12V/9Ah Inside carton
⑤BOX OF BATTERY 1 Inside carton
⑥REAR OVERCLOTH 1 On ATV
⑦ SEAT 1 Inside carton
①
INSTALL STEP：②
1. TAKE①、②、③、④OUT OF THE BOX ③
2. OPEN THE ②PACKING，INSERT④.
3. OPEN①PACKING，PRESS INTO ②。 ④
4. AFTER PUT INTO ELECTROLYTE，CLOSE ③。 ⑤
5. PUT④INTO⑥’S RED MARK（+）CONNECT RED POLE TO RED WIRE，（—）AND BLACK TO BALCK
6. BUTTON⑦ON⑥。
BLACK
⑥
NOTICE：
RED
1. PLS REFER INSTRUCTION ‘S THE WAY OF INJECTING
ELECTROLYTE WHICH PUT INTO THE BOX.
⑦