Rompa LED Shadow User manual

1. Product Name
LED Shadow™
2. Product Code
20714
3. Colour
Black
4. Brief Description
Voice-activated LED UV black light
5. Contents
1 x LED Shadow™light unit
1 x power cable
2 x flush mount brackets with screws
6. Snoezelen® Stimulations
Sight
7. Best Use
Use with fluorescent products in a darkened environment.

8. Compatible ROMPA® Products
ROMPA® offers a range of fluorescent and UV reactive products –please visit
www.rompa.com for more information.
9. Starting Up
Because of the nature of this black light, it is not advisable to take any short-cuts
when installing or using this product. Please read the entire manual and familiarise
yourself with the product and the installation instructions before using it.
10. Detailed Description
Voice-activated LED UV black light. Maintenance-free as no delicate UV tubes.
Features blackout/static/dimmer/strobe, built-in automatic programs and additional
power output for daisy-chaining units together. Use with your white and fluorescent
products. 90V-240V. Weight 2.2kg.
11. Safety
For indoor, dry environments only. Keep away from moisture.
Keep away from flammable objects and sources of heat (minimum distance of 1m).
Supervise the use of this product.
Avoid looking directly into the light.
Limit exposure to UV light –a maximum of 1 hour for adults and 5 hours for children,
assuming that the UV light is at ceiling height. If a user is to continually stand at the
light then exposure should be limited to one hour.
Do not use this product if the covers are open or if any internal component is
missing.
Should this product or its power cord become damaged, cease use of it immediately.
Connect the product to mains of the correct voltage –check the label on the
product.
Unplug the plug –do not pull the power cord to unplug it.
If mounting the product overhead, secure to a fastening device using a safety cable.
Do not touch the product’s housing when operating because it may be very hot.
Never connect the product to a dimmer.
Make sure to replace the fuse with another of the same type and rating.
Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
The maximum ambient temperature (Ta) is 104°F (40°C). Do not operate the product
at higher temperatures.
In the event of a serious operating problem, stop using the product immediately.

12. Technical Specification
Size: 36L x 25W x 17cmH
Weight: 2.2kg
Voltage: 100V-240V 50/60Hz

13. Installation
Unpack, identify all the parts and keep the packaging in a safe place.
Make sure the product is appropriately earthed.
Mounting:
1. Choose an appropriate mounting location, bearing in mind the following:
Make sure there is easy access to the product for maintenance and
programming purposes.
Adequate ventilation is required –at least 50cm from adjacent surfaces.
The product should be plugged in directly to the mains without using dimmers.
Any fixture used must be capable of supporting the weight of the product and
must appropriate to the construction of the surface the product will be attached
to.
Use a safety cable/chain to further secure the LED Shadow.
If linking multiple products, ensure these are close enough together for power
linking cables to reach.
The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.

AC Power:
The LED Shadow™ has an auto-ranging power supply and it can work with an input voltage
range of 100-240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit
breaker, power outlet and wiring), use the current value listed on the label affixed to the
product or refer to the product specification chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit (Circuit breaker or fuse). Make sure that
the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
Never connect the product to a rheostat (variable resister) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 –100% switch.
Fuse Replacement:
Disconnect the product from the power outlet before replacing the fuse.
Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
Pry the fuse holder out of the housing.
Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
Insert the fuse holder back in place and reconnect power.
Configuration (DMX Linking):
The LED Shadow can work with a DMX controller. Set the product in DMX mode to control
with a DMX controller.
Connect the product to a suitable power outlet.
Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket
on the product.
When selecting a starting DMX address, always consider the number of DMX channels the
product uses. If you choose a starting address that it too high, you could restrict the access
to some of the product’s channels.
The LED Shadow uses 3 DMX channels which defines the highest configurable address to
510.
To select the starting address, do the following:
Press <MENU> repeatedly until “Addr” shows on the display
Press <ENTER> and d001-510 will show on the display
Use <UP> or <DOWN> to select the starting address.

Press <ENTER>.
DMX Channel Assignments and Values:
You will require a suitable DMX controller and appropriate serial data link cables.
Fixtures on a serial data link must be daisy-chained on one single line.
Cabling must have a male XLR connector at one end and a female XLR connector on the
other end.
Setting up a DMX Serial Link:
Connect the male 3 pin connector of the DMX cable to the female output 3 pin connector of
the controller.
Connect the end of the cable coming from the controller (which will have a female 3 pin
connector) to the input connector of the next fixture (a male 3 pin connector).
Repeat for further devices.

Standalone/Master-Slave Fixture Linking:
Connect the male 3 pin connector of the DMX cable to the female output 3 pin connector of
the first device.
Connect the end of the cable coming from the first device (which will have a female 3 pin
connector) to the input connector of the next device (a male 3 pin connector).
Repeat for further devices.
Operation:
To access the control panel functions, use the four buttons located under the display. Please
refer to the Product Overview to see the button locations on the control panel.
Configuration (stand-alone):
Set the product in one of the stand-alone modes to control without a DMX controller.
Connect the product to a suitable power outlet.
Note: Never connect a product that is operating in any stand-alone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX signals that
could interfere with the DMX signals from the controller.

Auto Programmes:
To run an auto program, do the following:
Press <MENU> repeatedly until Aut shows on the display
Press <ENTER> and Aut0-5 will show on the display.
Use <UP> or <DOWN> to select the desired program.
Press <ENTER> and S. 01-99 will show on the display.
Use <UP> or <DOWN> to increase or decrease the programme speed.
Press <ENTER>.
To run the LED Shadow™ in sound activation mode, follow the instructions below:
1. Press <MENU> repeatedly until Sou shows on the display.
2. Press <ENTER> Soud will show on the display
3. Turn the sensitivity knob until the product responds to the beat of the music.
In sound activation mode, the product will only respond to low frequencies of music (bass
and drums).
Manual Mode:
To turn the LED Shadow in manual mode, follow the instructions below:
Press <MENU> repeatedly until CoL shows on the display.
Press <ENTER> and CoLo will show on the display.
Press <ENTER> again and L.00-255 will show on the display.
Use <UP> or <DOWN> to increase or decrease the dimmer value.
Press <ENTER> and S. 0-8 will show on the display.
Use <UP> or <DOWN> to increase or decrease the strobe rate.
Press <ENTER>.
Display Timeout:
To turn the display timeout on or off, do the following:
Press <MENU> until SYS shows on the display.
Press <ENTER> and LEdS, tESt, or rESt will show on the display.
Use <UP> or <DOWN> to select LEdS.
Press <ENTER> and on or oFF will show on the display.
Use <UP> or <DOWN> to select whether the display timeout should be on or oFF.
Press <ENTER>.
Test Mode:
To reset the software of the LED Shadow, do the following:
Press <MENU> until SYS shows on the display.
Press <ENTER> and LEdS, tESt or rESt will show on the display.
Use <UP> or <DOWN> to select rESt.
Press <ENTER>.

Reset:
To reset the software of the LED Shadow, do the following:
Press <MENU> until SYS shows on the display.
Press <ENTER> and LEdS, tESt, or rEST will show on the display.
Use <UP> or <DOWN> to select rESt.
Press <ENTER>.
Master/Slave Mode:
The Master/Slave mode allows a single LED Shadow product (the “master”) to control the
actions of one or more LED Shadow products (the Slaves) without the need of a DMX
controller. The master product will be set to operate in either Automatic mode or Sound-
Activation mode, while the slave products will operate in unison with the master product.
Configure the products as indicated below:
Slave products:
Press <MODE> until SLA shows on the display.
Press <ENTER> to accept. SLAV will show in the display.
Connect the DMX input of the first slave product to the DMX output of the master product.
Connect the DMX input of the subsequent slave products to the DMX output of the previous
slave product.
Finish setting and connecting all the slave products.
Master Product:
Set the master product to run in Auto mode or Sound Activation Mode.
Make the master product the first product in the DMX daisy chain.
Configure all of the slave products before connecting the master to the daisy chain.
Never connect a DMX controller to a DMX string configured for Master/Slave operation
because the controller may interfere with the signals from the master.
Do not connect more than 31 slaves to the master.
14. Care and Maintenance
Clean the device regularly –typically twice a month. Dust can cause over-heating
and reduces light output.
To clean the product, follow the instructions below:
Always unplug after use and before cleaning or any maintenance. Allow the product
to cool before handling –allow at least 15 minutes. The fixture surface may reach
temperatures of up to 160°C (320°F).
Use a vacuum cleaner or dry compressed air and a soft brush to remove dust from
external surface and vents. Clean all glass with a mild solution of glass cleaner and a