Ronix 2513T User manual

2513T
ELECTRIC SCREW DRIVER DRILL

USER MANUAL 1
SPECIFICATIONS
Model 2513T
Rated Voltage 220V
Rated frequency 50HZ
Input power 280W
No load speed 0-440 , 0-1650RPM
Chuck capacity 3/8” (1-10mm)
Wood 26mm
Steel 10mm
Torque settings 18+1
Safety class ll
Net weight 1.3KG
WARNING!
To reduse the risk of injury user must read instruction manual.
GENERAL SAFETY RULES
WARNING!
Read all safety warnings and all instructions failure to follow all warning
and instruction may result in election shock fire and/or serious injury.
Save all warning and instructions for future reference The term “power
tool” in the warning refer to your mains operated (corded) power tool or
battery operated (cordless) power tool.
.WORK AREA
- Keep your work area clean and well lit. Cluttered benches and dark
areas invite accidents.
- Do not operate power tools in explosive atmospheres such as in the
presence of flammable liquids gases or dust. power tools create sparks
which may ignite the dust or fumes.

2ELECTRIC SCREW DRIVER DRILL
- keep children and bystanders away while operating a power tool.
distractions can cause you to lose control.
.ELECTRICAL SAFETY
- power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with grounded surfaces such as pipes radiators
ranges and refrigerators. There is an increased risk of electric shock if
your body is grounded.
- Don’t expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying pulling or unplugging
the power tool. keep cord away from heat oil sharp edges or moving parts.
damaged or entangled cords increase the risk of electric shock.
- when operating a power tool outdoors use an outdoor extension cord
marked “W-A” or “W”. these cords are rated for outdoor use and reduce
the risk of electric shock.
- If operating a power tools in a damp location unavoidable use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
.PERSONAL SAFETY
- Stay alert watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the influence
of drugs alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury.
- Use personal equipment. Always wear eye protection. safety equipment
such as duse mask non-skid safety shoes hard hat or hearing protection
used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source picking up or carrying the tool.

USER MANUAL 3
carrying power tools with your finger on the swich or energizing power
tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
- Do not overreach. keep proper footing and balance at all times. Proper
footing and balance enables better control of the tool in unexpected situations.
- Dress property. Do not wear loose clothing or jewellery. contain long
hair. Keep your hair clothing and gloves away from moving parts. Loose
clothes jewellery or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and
collection facilities ensure these connected and properly used. Use of
duse collection can reduce dust-related hazards.
.POWER TOOL USE AND CARE
- Do not force the power tool. Use the correct power tool for your
application.The correct power tool will do the job better and safer at the
rate for which it is designed.
- Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
- Disconnect the plug from the power source before making any
adjustments changing accessories or storing the tool. such preventive
safety measures reduce the risk of starting the tool accidentally.
- Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. power tools are dangerous in the hands of untrained users.
- Maintain power tools. check for misalignment or binding of moving
parts breakage of parts and sny other condition that may affect the
power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
- Keep cutting tools sharp and clean. properly maintained cutting tools
will sharp cutting edges are less likely to bind and are easier to control.

4ELECTRIC SCREW DRIVER DRILL
- Use the power tools accessories and tool bits etc. in accordance with
these instructions and in the manner intended for the particular type of
power tools taking into account the working conditions and the work
to be performed. use of the power tools for operation different from
intemded could result in a hazardous situation.
.SERVICE
- Have your power tool serviced by a qualitied repair person using only
indentical replacement parts. this will ensure that safety of the power
tools is maintained.
Special Safety Warnings for Impact Drill:
1) Wear ear protectors with impact drills. Exposure to noise can cause
hearing Loss.
2) Use auxiliary handles supplied with the tools.loss of control can cause
personal injury.
3) Hold power tool by insulated gripping surfaces wrien performing an
operation where the cutting accessory may contact hidden wiring or its
cord. Cutting accessory contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the operator an electric shock.
ADDITIONAL SAFETY REGULATIONS
WARNING!
Remove the plug from socket before carrying out any installationa
adjustment servicing or maintenance.
The manual should indicate the content as follow.
1) stay alert and use common sense when operating the tool. o not use
the tool when tired or under influence of drug alcohol or medicine.
2) Never put fingers on the switch button while moving the tools to avoid
unintentional starting of the tool.
3) Ensure the mounting screws and other assemblies are fixed properly
and securely before operate the tool. Turn on the switch and let the tool
work for 30 second in a safe position. Stop immediately if considerable

USER MANUAL 5
vibraton or other defects are detectedhave it repaired.
Wear hearing protection while operating the power tools. The declared
vibration total value has been measured in accordance with a standard
test method and may be used for companing one tool with another.
The declared vibration total value may also be used in a preliminary
assessment of exposure.
WARNING!
The vibration emission during actual use of the power tool can differ from
the declared total value depending on the ways in which the tools is used.
There is the need to identify safety measures to protect the operator that are
based on an estimation of exposure in the actual condition of use (taking
account of all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the trigger time).
ASSEMBLY
.CHANGING THE TOOL
-Before any work on the power tool(e.g.maintenancetool change etc.)as
well as during transport and storageset the rotational direction switch to
the center position.unintentional actuation of the on/off switch can lead
to injuries.
-The drill spindle is locked when the ON/OFF switch 5 is not pressed.
This makes quickconvenient and easy changing of the tool in the drill
chuck possible.
-Open the keyless chuk by turning in rotation direction until the tool can
be inserted.insert the tool.
-Firmly tighten the collar of the keylees chuck by hand in rotation direction.
.REPLACING THE DRILL CHUCK
Before any work on the power tool(e.g.maintenancetool change etc.)as
well as during transport and storageset the rotational dircttion switch to
the center position.unintentional of the on/off switch can lead to injuries.

6ELECTRIC SCREW DRIVER DRILL
.REMOVING THE SECURING SCREW
The keyless chuck is secured with a securing screw against unintentional
loosening from the drill spindle. completely open the keylees chuck and
unscrew the securing screw in rotation direction.
Please note that the securing screw has a left-hand thread.
.REMOVING THE DRILL CHUCK
Clamp the short end of a hex key into the keyless chuck. Place the
machine on a stable surface(e.g.a workbench). Hold the machine
firmly and loosen the keyless chuck by turning the hex key in rotation
direction. Loosen a tight-seated keyless chuck by giving the long end
of the hex key a light blow.Remove the hex key from the keyless chuck
and completely unscrew the keyless chuck.
.MOUNTING THE DRILL CHUCK
The drill chuck must be tightened with a tightening torque of approx.
20Nm Screw the securing screw in counter lock-wisw direction into the
opened keyless chuck; Tightening torque approx. 4-5Nm. Always use a
new securing screw, as the threads are covered with a thread-locking
compound that loses its effect after multiple usage.
.DUST/CHIP EXTRACTION
Dusts from materials such as lead-containing coatings, some wood
types, minerals and metal can be harmful to one’s health. Touching
or breathing-in the dusts can cause allergic reactions and/or lead to
respiratory infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are considered as carcinogenic,
especially in connection with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may only be worked by specialist.
Provide for good ventilation of the working place.
It is recommended to wear a p2 filter-class respirator.
Observe the relevant regulations in your country for the materials to be worked.

USER MANUAL 7
OPERATING
Never cover the air vents since they must always be open for proper
motor cooling.
STARTING OPERATION
.SWITCH ON AND OFF
This tool is started and stopped by pressing and releasing the trigger
on/off switch.
The speed can be adjusted in the high gear or in the law gear, by
controlling the trigger-pressing force.
For continuity operation, press the lock button while pressing the trigger.
Press again to release the lock.
.REVERSING THE ROTATIONAL DIRECTION
The F/R lever is used to reverse the rotational of the machine.
However, this is not possible with the on/off switch.
Right rotation: for drilling and deriving in screws, push the F/R lever left stop.
Left rotation: for loosening and unscrewing screws and nuts, press the
F/R lever through to the right stop.
SETTING THE TORQUE
with the clutch cap the required torque setting can be preselected in
(18+1) steps. It the correct setting, he insert tool is stopped as soon
as the screws is screwed flush into the material or when the adjusted
torque is reached.
The safety clutch is deactivated in the position, e.g. for drilling.
Select a higher setting or switch to the symbol when unscrewing screws.

8ELECTRIC SCREW DRIVER DRILL
.ADJUSTING THE SPEED
The speed of the switched on power tool can be variably adjusted on
how far the on/off switch 5 is pressed.
Fully automatic spindle locking (auto-lock).
When the on/off switch 5 is not pressed, the drill spindle and thus the too
holder are locked.
This enables screws to be screwed in, allows for the tool to be used as
a screwdriver.
.RUN-ON BRAKE
-When the on/off switch is released, the chuck brakes to a stop, thus
preventing the run-on of the tool.
-When the on/off switch is released, the chuck brake to a stop, thus
preventing the run-on of the tool.
-When driving in screws, wait until the screw is screwed in flush with the
material and then release the on/off switch.
-By doing so, the head of the screw does not penetrate into the material.
Working instructions
-Apply the power tool to the screw only it is switched off.
-Rotating tool inserts can slip off.
.TIPS
-After longer period of wording art law speed. Allow the machine to down
by running it for approx.
-Minutes at maximum speed with no load.
-For drilling in metal, use only perfectly sharpened hss drill
bits (hss=high speed steel). before screwing larger, longer
screws into hard materials, it is advisable to predrill a pilot
hole with the core diameter of the thread to approx.2/3 of the
screw length.
-Light pressure on the on/off switch results in a low rotational speed.
Further pressure on the switch results in an increase in speed.
-Even when the power tool is used as prescribed it is not possible to

USER MANUAL 9
eliminate all residual risk factors.
-The following hazards may arise in connection with the power tool’s
construction and design:
1) Damage to lungs if an effective dust mask is not worn.
2) Damage to health resulting from vibration emission if the power tool
is being used over longer period of time or not adequately managed and
properly maintained.
WARNING!
This power tool produces an electromagnetic field during operation.
This field may under some circumstances interfere with active
or passive medical implants. To reduce the risk of serious or fatal
injury, we recommend persons with medical implants to consult their
physician and the medical implant manufacturer before operating this
machine.
WARNING!
To ensure safety and reliability, all repairs should be performed
by an authorized servise center or other qualifiled service
organization.
.ENVIRONMENTAL PROTECTION AND GUARANTEE
Waste electrical products should not be disposed of with
household waste.
Pleas recycle where facilities exist. check with your with your local
authority or reatailer for recycling advice.
Residual risk
Even when the power tool is as prescribed it is not possible to eliminate
with the power tools construction and design:
1) dameage to lungs if an effective dust mask is not worn.
2) damega to hearing if effective hearing protection is not worn.
3) damages to health resulting from vibration emission if the power
tool is being used over longer period of time or not adequately

10 ELECTRIC SCREW DRIVER DRILL
managed and properly maintained Waring this machine produces
an electromagnetic filed during operation.this filed may under some
circumstances interfere with active or passive medical implants.to
reduce the risk of serious or fatal injury,we recommend persons with
medical implants to consult their physician and the medical implant
manufacturer before operating this machine.