Roswell F Series User manual

REV. 191118
Information: [e-mail]
Warranty:[e-mail]
F-Series Tower Speaker Adapter# C813-20144
If you have any questions please call : 1-321-638-1331
www.roswellmarine.com
F-Series Tower
Speaker Adapters

Welcome to the Family.
We at Roswell started a revolution in the wakeboard industry back in 1998, and have since
expanded into marine audio and other branches of the marine industry. Even now, over 20
years later, we continue to push the boundaries.
We are fully committed to going past industry expectations every day to make your
boating experience more enjoyable. With the input of our dealers, team riders, and boaters
around the world, our goal remains to redene the marine industry day in and day out. We
will not be conned to our desks; we are out on the water testing our full line of products to
ensure your days on the water are as hassle-free and enjoyable as possible.
If you have any questions about your speakers or questions regarding installation, please
contact your authorized Roswell dealer. If you have further questions, please don’t hesitate
to contact us directly at (321)-638-1331 or by emailing [e-mail].
Table of Contents
Features
Warnings
Preparation
Wiring
R1 Pro Installation
Installing on Tower
Warranty
Tower Wiring Diagram
03
04
05
06
07 - 08
09 - 10
10
11

3
www.roswellmarine.com
Features
The F-Series Tower Speaker Adapters provide a solid platform to hang your speakers.
Machined from billet aluminum it is sure to rmly hold your speakers for years to come.
Clean design
The low prole design allows you to securely
mount speakers to your tower without
compromising the look.
F-Series Specic
The adapters have been designed to mount
Roswell speakers to the Supreme F-Series
tower,

4
www.roswellmarine.com
Warnings
• Bolts and screws tend to rattle loose over time due to the vibrations and shaking that
your boat experiences while on the water or in transit. Always check all your speakers are
securely fastened by checking speakers bolts for tightness before using your boat. If any
bolts are found to be loose remove them, apply red threadlock and re-tighten the bolts.
• Never hang o of the speaker under any circumstance.
• Be mindful of the head clearance to prevent head injuries.
• Be aware of your tow rope being sure not to get it wrapped around the speaker or any
other objects.
ATTENTION
Use and Care.
Before use do an inspection of your speakers, checking for loose hardware. We
recommend keeping a set of Allen keys in your boat. Even with threadlock bolts can still
loosen over time.

5
www.roswellmarine.com
Preparation
Preparation
THREADLOCKER
5/16”-18 x 0.75
X8
Wire Strippers
Crimps Knife
Red / Blue
Threadlock
Allen Key
3/16”
5/16”
3/32”
Package Contents
Tools Required
3/8”-16 x 1.5
3/8” Lock-washer
X4
X2 X8
Before you start make sure that you have all of the required tools to install your product.
Crimp connectors not included - If installing a new speaker, please use the crimp
connectors supplied with the speaker. Make sure you have enough connectors before
beginning the installation.
Heat gun Phillips Screwdriver
#2

6
www.roswellmarine.com
Wiring
Speaker (+) Speaker (+)
Speaker (-) Speaker (-)
LED 12V (+)
Blue LED (-)
Green LED (-)
Red LED (-)
LED 12V (+)
12V (-)
12V (-)
12V (-)
White
Optional - For use with RGB Controller
Optional - For use with RGB Controller
Yellow
Black
Blue
Green
Red
Crimp
Connector
Blue 12V (-)
Green 12V (-)
Red
Green
Blue
Output
Green
Red12V (-)
Yellow
12V (-)
Red
Blue Magenta
Cyan
12V (-)
Red
Blue 12V (-)
Green
White
Controllable /
Programmable
RGB
Blue
12V (-)
Green
Red
Blue
Green 12V (-)
Blue 12V(-)
Red 12V (-)
Green
Red
Tower Wiring
Speaker Wiring Harness
1
Wiring
Access the wires in the tower. Be careful
pulling out the wires. Next carefully cut the
shrink wrap to uncover the wires. Be cautious
not to cut through the wire insulation.
Strip 1/4” o of the wires and crimp the butt
connectors to the corresponding wires. Once
attached use a heat gun on the connectors
to seal the connections. Wire Strippers
Crimps
Heat Gun
Heat shrink
Connectors
X12 Tower Wires
Connectors
Deutsch
Connector
NOTE: R1 Pro wiring shown, please refer to your
speakers’ instruction manual if using a dierent
speaker See page 11 for the F-Series tower wiring diagram

7
www.roswellmarine.com
R1 Pro Installation
1
2
NOTE: disassemble the speaker on a clean
at surface to prevent scratches.
To detach the existing clamp, rst remove the
four at head phillips bolts on the front. Next
remove the three plastic pieces and carefully
place to one side, then carefully remove the
speaker from the case and disconnect the
wires. Place a rag/dropcloth in front of the
housing and lay the speaker down on it to
prevent damage.
Remove the four socket cap bolts and lock
washers as shown to release the clamp, carefully
remove the clamp from the speaker and put aside.
R1 Pro Installation
Allen Key
5/16
Phillips Screwdriver
#2

8
www.roswellmarine.com
R1 Pro Installation
3
Apply red threadlocker to four of the provided
3/8” bolts and with the adapter aligned as
shown, secure it to the speaker housing with a
lock washer on each bolt.
Allen Key
5/16
THREADLOCKER
Red
Threadlock
Re-connect the speaker wires and align
the speaker, making sure the gasket is in
place between the speaker and the housing.
Then install the three plastic pieces using
the original bolts with blue threadlocker, be
careful not to over tighten
4
THREADLOCKER
Blue
Threadlock Phillips Screwdriver
#2

9
www.roswellmarine.com
Installing on Tower
Installing on Tower
1
Thread the Deutsch connector through
the center hole of the adapter, and leave it
unplugged to give room for tools.
2
Using the 5/16” bolts with red threadlock,
install the forward bolt by hand, then the rear.
Tighten by hand until you have enough room
for the Allen key. Then tighten fully with the
Allen key.
Allen Key
3/16
THREADLOCKER
Red
Threadlock

10
www.roswellmarine.com
Installing on Tower / Warranty
Roswell Limited Warranty
Roswell warrants all new R1 Pro Tower Speakers against defects in material and workmanship for a period of
TWO (2) YEARS from the original date of purchase. This warranty is not transferable and applies only to the
original retail purchaser from an authorized Roswell retailer. Upon inspection by Roswell, should service be
necessary under this warranty for any reason due to manufacturer defects, Roswell will, at our own discretion,
repair or replace the defective product with new or similar conditioned product at no charge.
THIS WARRANTY DOES NOT COVER INSTALLATION OR DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE, IMPROPER WIRING, COSMETIC DAMAGE DUE TO NORMAL WEAR AND TEAR, EXPOSURE
TO CHEMICALS OR HARSH ENVIRONMENTS, OPERATION OUTSIDE OF THE MANUFACTURERS
RECOMMENDATIONS OR SPECIFICATIONS, OR AGAINST INSTRUCTIONS IN OWNERS MANUAL. IN ADDITION,
ANY PRODUCT THAT HAS BEEN OPENED, TAMPERED WITH OR MODIFIED, OR IF ANY SERIAL NUMBERS HAVE
BEEN REMOVED, WILL NOT BE COVERED BY ANY PART OF THE MANUFACTURES WARRANTY.
All warranty claims must rst be made in direct contact with Roswell’s warranty department. When rst contact
is made the warranty representative will issue an RA # to open a claim. All warranty returns should be sent to
Roswell freight prepaid and must be accompanied by proof of purchase (a copy of original sales receipt). Direct
returns from consumers or non-authorized retailers will be refused unless specically authorized by Roswell with
a valid return authorization number (RA#).
All warranty returns should be packed in the original packaging and must be accompanied by a copy of the
original sales receipt. Product damage during shipping will not be covered under this warranty. The customer or
retailer may choose to have this damage repaired at the normal “Out of Warranty” repair cost.
In no event will Roswell be liable for incidental, consequential, or other damages resulting from the use of
this product. This includes but is not limited to, damage of hearing, property or person, damage based upon
inconvenience or on loss of use of the product, and to the extent permitted by law, damages for personal injury.
This warranty applies to products being sold and used in the United States of America and Canada. In all other
countries please contact your authorized Roswell representative.
For warranty and non-warranty repairs, please contact Roswell.
Phone: [phone]
Email: [e-mail]
3
Finally, connect the Deutsch
connector to the speaker and
carefully push the excess wire up
into the tower.

11
www.roswellmarine.com
F-Series Tower Wiring
PORT SIDE
AUDIO STARBOARD SIDE
LIGHTS
WHITE+
WHITE & BLACK -
GREEN +
GREEN & BLACK -
16 AWG 16 AWG
DT04-4P W4P
(4x) 0460-202-16141
3
2
4
1
REAR VIEW OF TOWER
AT WIDEST DISTANCE
16 AWG16 AWG
BLACK -
DARK GREY +
LIGHT BLUE +
3
2
4
1
DT04-4P W4P (4x) 0460-202-16141
123 4
12 3 4
16 AWG 16 AWG
DT04-4P
W4P (4x) 0460-202-16141
3
2
4
1
1
234
GREY+
GREY & BLACK -
PURPLE +
PURPLE & BLACK -
REAR VIEW OF TOWER
ROSWELL
Rev. 17-SEPT-2018-DW
F SERIES TOWER WIRING DIAGRAM
Port Speakers
Stbrd
Speakers
DARKBLUE
+
9
8 7 6
5
4 3 2
DT06-06SA
W6S
(6x) 0462-201-16141
DT04-06PA W6P (6x) 0460-202-16141
DT04-12PA
W12P
(9x) 0460-202-16141
DT06-12SA W12S (9x) 0462-201-16141
1
QUICK
CONNECTOR
QUICK
CONNECTOR
ANCHOR LIGHT
SPEAKER LIGHT
COMMON GROUND
COURTESY LIGHT
6
5
4 3 2
1
10
1 2 3
6 5 4
1 2 3
6 5 4
BLACK
DARK BLUE
WHITE
WHITE & BLACK
GREEN
GREEN & BLACK
GREY
GREY & BLACK
PURPLE
PURPLE & BLACK
(3x) 114017(3x) 114017
BLACK -
-
DARK GREY +
LIGHT BLUE +
DARKBLUE
+
11 12
2
12
1
9
4
10
3
7
6
8
5
11
2
12
1
9
4
10
3
7
6
8
5
11