Royal garden YJAF-819A User manual

5

3
AA DD
BB EE
x 8
CC BB
FF
BB
GG
BB
HH
x 2
x 1
x 4
x 4
x 1
x 1
x 1
AA
Quantity
Part
BB
CC
Description
M 6x10 bolt
M 6x15 bolt
M 10x22 bolt
2
1
DD
EE
FF
GG
HH
M10x30 bolt
M 10 washer
S5 Allen Wrench
S8 Allen Wrench
Wrench
1
1
8
4
4
1
Pre-Assembly
PLANN ING ASSEMBLY
Read all instruction before assembly.
To avoid damaging this produt, assemble it on a soft, non-abrasive surface such as cardboard.
NOTE: More than one person may be required to
assemble this product.
Pleasecontact [phone] for further assistance.
WWW.ROYALGARDEN.COM

A Upper Bracket 1
Part Description Quantity
4
B Lower Bracket 1
A
B
x 1
x 1
D
C
x 1
x 1
BB
EBB
FBB
G
x 1 x 2
x 2
BB
H
x 2
I J
BB
K
BB
L
BB
N
BB
O
BB
P
BB
Q
BB
RBB
S
x 2
x 2
x 4
x 1
x 1
x 1
x 1 x 1 x 4 x 4
M
x 1
C Cylinder 1
D 1
E
Upper base cover
KD base cover 1
F 2
G Sand bag 2
H 2
I
Support tube rim
Lock panel 2
J Side panel 2
K Base Corner 4
L Crank 1
M Sunshade 1
N Pedal 1
O Support tube 1
P Turntable 1
Q Lower Pole 1
R Long Steel Hook 4
S Short Steel Hook 4
Lower base cover
Pre-Assembly (continued)
OFFSET UMBRELLA

1
5
CONNECTING THE CYLINDER TO THE BRACKET
Pull out lower pole (Q) from cylinder (C).
Attach support tube (O) onto the turntable (P) using M6x10 combination bolts (AA).
Attach the upper bracket ( A onto the lower bracket B).
Attach turntable (P) and cylinder (C) onto bracket using M10x22 (CC) and M10x30 (DD) combination bolts and M10 washer (EE).
M Q
C
③
④
GG
C
CC
EE
DD
P
O
1
2
AA
FF
A
B
Umbrella Assembly
Pleasecontact [phone] for further assistance.
WWW.ROYALGARDEN.COM
NOTE: This umbrella should be set up in its desired
location to avoid moving it after assembly.

1
3
2
4
2
6
Umbrella
Assembly (continued)
BB
K
BB
H
S
R
CONNECTING BASE CORNER AND SUPPORT TUBE
Insert the base corner (K) into the four ends of the assembled brackets.
Connect the two pieces of the support tube rings (H).
Slide the support tube rim (H) down to the lower cylinder.
Attach long steel hook (R) and short steel hook(S) onto the assembled breackets.

1
3
2
3
Umbrella Assembly (continued)
7
CONNECTING THE LOCK PANELS AND SEND BAGS.
G
I
J
J
J
Slide the perforated lock panels (I) and side panels (J) downward between the base corner (K).
Place the sand bags (G) in the umbrella base. Pull to open the velcro punch on the sand bag (G) and fill with sand.
After filling the sand bags (G), close the ouch and ensure the velcro is sealed. Lock the two sections of the sand bags (G) togerther.
Pleasecontact [phone] for further assistance.
WWW.ROYALGARDEN.COM

4
8
Umbrella Assembly (continued)
CONNECTING THE BASE COVER
Ensure the locking mechanism on the lock panel (I) is in the OPEN position by using the wrench (HH) as shown in gure 1.
Ensure the locking mechanism on the lower base cover (F) is in the OPEN position by using the wrench (HH) as shown in gure 2.
Attach the lower base cover (F) to the side panels (J).
Close the lower base cover (F) and ensure they are fully closed. Lock the lower base cover (F) and the lock panel (I) by turning the locking
mechanisms to the CLOSE position using the wrench (HH) as shown in gure 6 and gure 7.
HH
F
J
12
34
5
67

5
9
D
E
N
FF
AA
Q
C
CONNECTING BASE COVER
Attach the KD base cover (E) to the assembled base then attached the upper base cover (D) on the KD base cover (E).
Lock pedal to the assembled support using M6x10 combination bolts (AA) and S5 Allen Wrench (FF).
Attach lower pole (Q) to cylinder (C).
Umbrella Assembly (continued)
Pleasecontact [phone] for further assistance.
WWW.ROYALGARDEN.COM
1
2
3
4
5

6
10
CONNECTING SUNSHADE TO THE THE CYLINDER.
Insert the sunshade (M) into the cyli nder (C) then lock with M6x15 combinnation bolts (BB).
M
C
Q
FF
BB
Umbrella Assembly (continued)
1
2

7
11
CONNECTING THE CRANK
C
L
Umbrella Assembly (continued)
Attach the crank (L) to the handle.
Pleasecontact [phone] for further assistance.
WWW.ROYALGARDEN.COM
2
1
2
3

8
12
For best results, clean the frame and fabric with a damp cloth, and dry thoroughly. This will help prevent
particles that may accumulate.
Do not clean with abrasive materials, bleach, or solvents.
Store the umbrella in a dry, sheltered place when not in use.
Tie the canopy closed on windy days to prevent damage to the umbrella.
Keep the umbrella away from fire, extreme heat freezing conditions, and inclement weather such as rain, hail, sleept, snow, or wind.
CHECKING THE SUNSHADE
Umbrella Assembly (continued)
Care andCleaning
Tread the pedal to rotate the sunshade.
1
2
3
mildew by removing dirt

Retain this manual for future use.
Questions, problems, missing parts? Before returning to the store
call Royal Garden Customer Service.
6 a.m. - 9 p.m., EST, 9 a.m. - 5 p.m., PST, Monday - Friday
[phone]
WWW.ROYALGARDEN.COM