ROYLITE BSW350 User manual

1
Beam Spot Wash 3 in 1
17R 350W Bulb
User manual
Thanks for choosing our goods please read this manual carefully before your operating

2
Introduction
350W Beam Spot Wash 3 in 1 Moving head light
Model:BSW350
Voltage:AC100V-240V 50/60Hz
Power Consumption:500W
Light source:YODN R17 350W
Color Temperature:8000K
Beam Angle:1.5°- 35° linear fast zooming.
Focus:High precision optical lens,electronic linear control
Linear Dimmer:Mechanical dimmer 0-100%
Color Wheel:14 fixed color+open,half-tone effect, linear color conversion, bi-directionally
rotatable at variable speeds and rainbow effect
Rotating Gobo:12 rotating gobos+White,bi-directional rotatable and gobo shaking at variable
speeds
Fixed gobo: 17 interchangeable gobos +white, and bi-directionally rotatable and gobo
shaking at variable speeds
Prism:16 facet circular prism & 6 facets linear prism
Dimmer:0-100% linear dimmer
Strobe:1-18/second,double lens strobe with adjustable speed
Pan and Tilt: Smoothly,automatic Pan/Tilt position correction,speed adjustable
Range:Pan540°，Tilt 280°
Effect:Color+Gobo+Prism+Strobe automatic operation function
Cooling:Fan Cooling
Control mode:Standard DMX 512, 3 pin,5 pin connector
Channel mode:16CH / 24CH / 30CH
Display Interface:LCD screen both in Chinese and English
IP rate:IP20,Built-in overheat protection,triggered high voltage protection.
Net Weight:19KG
Gross Weight:21KG(Carton)

3
Safety Information
The following symbols are used to identify important safety information on the product and in this manual:
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product.
This product is for professional use only. It is not for household use.
！
DANGER!
Hazardous
voltage. Risk
of lethal or
severe electric
shock.
WARNING!
Burn hazard.
Hot surface.
Do not
touch.
WARNING!
Refer to user
manual.
WARNING!
High
brightness
light source,
With risk of
burned eyes.
Protectio
n from
burn and
fire.
DANGER!
Safety hazard.
Risk of severe
injury or death.
WARNING!
Wear
protective
Eye wear.
Warning!
High brightness light source,don’t look at the light directly so that keep the risk of burned
eyes away.
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire and burn hazards, electric
shock and falls.
Read this manual before installing, powering or servicing the fixture, follow the safety
precautions listed below and observe all warnings in this manual and printed on the
fixture.
If have any problem,please contact the supplier.

4
PROTECTION FROM ELECTRIC SHOCK
• Disconnect the fixture from AC power before removing or installing any cover or part and when not in use.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and electrical codes and has both overload and
ground-fault (earth-fault) protection.
• Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated
for the current requirements of all connected devices.
• Power input and throughput cables must be rated 20 A minimum, have three conductors 1.5 mm²(16 AWG)
minimum conductor size and an outer cable diameter of 5 - 15 mm (0.2 - 0.6 in.). Cables must be hard usage type
(SJT or equivalent) and heat-resistant to 90° C (194° F) minimum. In the EU the Cable must be HAR approved or
equivalent.
• Use only Neutrik Powercon NAC3FCA cable connectors to connect to power input sockets. Use only Neutrik
Powercon NAC3FCB cable connectors to connect to power throughput sockets.
• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other
Component is damaged, defective, deformed, wet or showing signs of overheating. Do not reapply
power until repairs have been completed.
• Do not expose the fixture to rain or moisture.
PROTECTION FROM BURNS AND FIRE
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
• The exterior of the fixture becomes hot during use. Avoid contact by persons and materials. Allow
the fixture to cool for at least 10 minutes before handling.
• Keep all combustible materials (e.g. fabric, wood, paper) at least 100 mm (3.9 in.) away from the
fixture.
• Keep flammable materials well away from the fixture.
• Ensure that there is free and unobstructed airflow around the fixture.
• Do not expose the front glass to sunlight or other strong light sources from any angle.
• Do not illuminate surfaces within 200 mm (7.9 ins.) of the 350BSW.
• Do not attempt to bypass thermostatic switches or fuses.
• Do not stick filters, masks or other materials onto any optical component.
• Do not modify the fixture in any way not described in this manual
PROTECTION FROM INJURY
•When light up the fixture,please don’t look at the optical lens with eyes directly.Besides, don’t use the camera
light to point at the optical lens.
• Fasten the fixture securely to a fixed surface or structure when in use. The fixture is not portable when installed.
• Ensure that any supporting structure and/or hardware used can hold at least 10 times the weight of all the
devices they support.
• Allow enough clearance around the head to ensure that it cannot collide with an object or another fixture when
it moves.
• Check that all external covers and rigging hardware are securely fastened.
• Block access below the work area and work from a stable platform whenever installing, servicing or moving the
fixture.
• Do not operate the fixture with missing or damaged covers, shields or any optical component.

5
Using for the first time
AC power
Power voltage
Important! After unpacking,please check the goods damage or not,which due to the transportation. If
you find damage, please do not use this item, then contact the dealer or manufacturer as soon as possible.
•Please read the “Safety Information”before using the fixture.
• Check that the local AC mains power source is within the fixture’s power voltage and frequency ranges.
•Please make sure the fixture use in “Safety Information” term.
Warning! Read “Safety Information” starting on page 5 before connecting the BSW350 to AC mains
power.
Warning! For protection from electric shock, the BSW350 must be grounded (earthed). The power
distribution circuit must be equipped with a fuse or circuit breaker and ground-fault (earth-fault)
protection.
Warning! Socket outlets or external power switches used to supply the BSW350 with power must be
located near the fixture and easily accessible so that the fixtures can easily be disconnected from
power.
Important! Do not insert or remove live Neutrik PowerCon connectors to apply or cut power, as this
may cause arcing at the terminals and damage the connectors.
Important! Do not use an external dimming system to supply power to the BSW350 as this may
cause damage to the fixture that is not covered by the product warranty.
Warning! Check that the voltage range specified on the fixture’s serial number label matches the local AC mains
power voltage before applying power to the fixture.
BSW350 fixtures accept AC mains power at 100-240 V nominal, 50/60 Hz. Do not apply AC mains power to the
fixture at any other voltage than that specified on the fixture’s serial number label.

6
Data link
Connecting the data link
Menu chart：
LCD display home page Introductions
1 — Shows current DMX address in big font size.
2 — click to open main menu.
A DMX 512 data link is required in order to control a BSW350 via DMX.
The BSW350 has 5-pin XLR connectors for DMX data input and output. The pin-out on all connectors is pin 1 = shield, pin 2 = cold
(-), and pin 3 = hot (+). Pins 4 and 5 in the 5-pin XLR connectors are not used in the BS350 but are available for possible additional
data signals as required by the DMX512-A standard.
Standard pin-out is pin 4 = data 2 cold (-) and pin 5 = data 2 hot (+).
The number of fixtures is either limited to 256 or limited by the number of DMX channels required by the fixtures in relation to the
maximum 512 channels available in one DMX universe, whichever limit is lower. Note that if independent control of a fixture is
required, it must have its own DMX channels.
Fixtures that are required to behave identically can share the same DMX channels.
To add more fixtures or groups
Connecting the data link To connect the LIGHT to data:
1. Connect the DMX data output from the controller to the closest BSW350 male 5/3-pin XLR
DMX input connector.
2. Connect the DMX output of the fixture closest to the controller to the DMX input of the next
fixture and continue connecting fixtures output to input.
3. Terminate the last fixture on the link with a 120 Ohm resistor.
1
LED 2
LED 1

7
3 — click to set the language.
4 — click to turn on or off the lamp.
5 — click to set the channels mode, and the figures shows current channels number.
6 — click to reverse the display.
7 — Show the DMX signal state. Click to toggle Master/Slave mode, and the figure’s
meaning is as follows:
Green down arrow: The device is receiving DMX signal from console.
Yellow “X” ：The DMX signal is lost.
Blue up arrow: The device is working on master mode, and it is sending signal to
outside now.
8 — click to set the running mode. If the figure is highlighted, that means the device is
running in this mode as is shown.
9 — Show the running mode when the DMX signal is lost but the current running mode is still
set as DMX. If the figure is highlighted, that means the device is running in this mode as is
shown. It is active on power-on only, refer to description of menu “Running Cnfg” – “DMX
Lost” .
10 — Error information. It shows a green “√” sign if has no error and a yellow “!” sign if has
some errors when self-test. Click to open the error information menu for more details.
LED 1 – Blue LED。 If it blinds， means the DMX signal is detective； If it keeps on, means the
device is running on Master mode; If it shut down, means the DMX signal is lost. The
LED can be shut down simultaneously with the LCD backlight if the menu “Display
Config” – “LED Indicator” was set to “Auto”.
LED 2 – Red LED. It blinds when run on “Sound(music)” mode，or keep on when some error
state were detected. The LED can be shut down simultaneously with the LCD backlight
if the menu “Display Config” – “LED Indicator” was set to “Auto” except errors detected.
Level 1
Level 2
Level 3
Level 4
Option/Value range
DMX Addr
1 - 512
Channel Mode
0 - 255
Reset Operating
Reset All
Pan/Tilt
Color
Gobo
Dim
Zoom/Prism
etc.
Run
DMX/Test(Factory)/Test(Gobo)/Test

8
(color)/Music/Program
Lamp
Off/On（Curr-On/Off）
Manual Control
Pan
…
Auto return
10 sec/20 sec/never
Running Cnfg
Tilt Cnfg
Reverse
N/Y
Origin
0 - 255
End
0 - 255
Pan Cnfg
Reverse
N/Y
Origin
0 - 255
End
0 - 255
M/S Mode
Slave/Master
Music Ctrl
Cnfg
Ctrl Mode
Dim/Color/Gobo
Other CHN
DMX/Auto/Manual
Sensitivity
0 - 10 - 20
Mixed Scene
Scenes Num.
1 - 8
Scene Edit
Scene Index
0 - 7
Step Index
0 - 29
Step Edit
Time
0 - 255
Chn
1 - Max channels
Value
0 - 255
Copy
Paste
Record
Lamp Power
Eco/Std
Black Out
Pan/Tilt
N/Y
Color
N/Y
Gobo
N/Y
Time/Speed

9
Mode
Pan/Tilt
Speed/Time
Rot.Gobo
Speed/Time
Random
Strobe Sync
N/Y
Display Config
Sleep
30 sec/2 min/5 min/10 min/Keep on
Brightness
1 - 10
Reverse
N/Y
Indicator
Auto/KeepOn
Advanced
Fine Adj
Factory
Settings
DMX Lost
Middle/Keep/Test(Factory)/Test(Gob
o)/Test(color)/Music/Program
Quick Position
Color
N/Y
Static Gobo
N/Y
ROT. Gobo
N/Y
Auto Gobos
N/Y
Fan Speed
Auto/Max
Language
中文/Eng/Español
Lamp Off
NoAct/Sleep
Turn Off Bat
P/T Correction
N/Y
Allow DMX
save
N/Y
Clear Lamp
Time
Recover
Setting
Info
DMX Monitor
Chn
1 - Max channels
Value
State Monitor
CPU1 TEMP ℃
CPU2 TEMP ℃
Lamp TEMP ℃

10
Battery (%)
Lamp
Servicetime
ThisTime(m)
Total(h)
Err State
EEPROM
Well/Err
Sensor Err
Pan Raster
Well/Err
Tilt Raster
Well/Err
Pan Reset
Well/Err
Tilt Reset
Well/Err
Color wheel
Well/Err
Sta.gobo
Well/Err
RotGoboWheel
Well/Err
Rot.gobo
Well/Err
Focus
Well/Err
Zoom
Well/Err
Prism
Well/Err
LampComm
Well/Err
CPU2 Comm
Well/Err
Lamp Overheat
N/Y
CPU1 OverHeat
N/Y
CPU2 OverHeat
N/Y
Flash Err
N/Y
RAM Err
N/Y
License Expired
N/Y
P/T Reference
Speed
Pan(.01s)
Tilt(.01s)
Time Left(h)
Input SN.
ID
Product Code
DMX Addr: Use the menu to set desired fixture address setting
Channel Mode: Use the menu to select desired DMX channel mode. The numbers on the menu

11
represents the number of control channels.
Reset Operating: Reset Motors
Reset All: Use the menu to reset all motors
Pan/Tilt: Use the menu to reset Pan and Tilt
Color: Use the menu to reset color
Gobo: Use the menu to reset gobos
Dim: Use the menu to reset dimmer
Zoom/Prism etc.: Use the menu to reset focus, zoom, prism and frost. The 6 facet prism
will reset automatically if it is inactive （The reset process takes 6
seconds）
Run:Use the menu to select operational mode
Following is the instructions of the menu options：
DMX：Controlled by DMX512 signal。
Test(factory)：Controlled by built-in program which is for factory test.
Test(gobo): Controlled by built-in program which display the rotating gobos and prisms.
Test(color): Controlled by built-in program which display the static gobos , prisms and colors.
Music ：Controlled by the volume of the ambient sound 。Use the menu [Running
Cnfg]-[Music Ctrl Cnfg] to set up the running mode and microphone sensitivity.
Program：
Controlled by User's program。 User the menu [Running Cnfg]- [Mixed Scene] and
[Scene Edit] to set up or edit the scenes。
Lamp: Use the menu to turn on or off the lamp. It will take effect after 3 seconds , if the value was
switched back in 3 seconds, the operation will be canceled. If the lamp was turn off，it must
wait for 1 to 2 minutes before it can turn on again。 You can set the menu value to “on” and it will
turn on automatically after 1 to 2 minutes。
An example of the value is shown below :
Manual Control: Set DMX value manually
Pan: Set the DMX value of Pan.
…….
Auto return: Return to previous menu automatically if no any operation. Use the menu to
select waiting times.
On（Curr-Off）
The value which is saved. When the current value changed by
click menu, this value keep consistent.
The current state, it can be switched by click the menu or setting the
DMX value of function channel.

12
Running Cnfg: configuration of Running.
Tilt Cnfg:
Reverse: The item allows to invert Tilt movement
Origin: Set desired Origin value to change Tilt movement range (set the DMX value to
0 before changing this value, the tile motor will move when changing this value)
End: Set desired final stop value to change Tilt movement range (set the DMX value to
255 before changing this value, the tile motor will move when changing this value)
Pan Cnfg:
Reverse: The item allows to invert Pan Movement
Origin: Set desired Origin value to change Pan Movement range (set the DMX value
to 0 before changing this value, the tile motor will move when changing this
value)
End: Set desired final stop value to change Pan movement range (set the DMX value
to 255 before changing this value, the tile motor will move when changing this
value)
M/S Mode: Slave mode is for receiving external DMX signals and Master mode is for
sending DMX signals to external slave fixtures
Music Ctrl Cnfg: Music Control configuration
Ctrl Mode: Use the menu to set desired sound control effect
Following is the instructions of the menu options：
Dim：Dimmer by sound control.
Color：Random color selection by sound control.
Gobo：Random static gobo selection by sound control.
Other CHN: Use the menu to set the control mode for other channels except music
control channels
Following is the instructions of the menu options：
DMX ：Control by DMX signal. In this control mode, the shutter or
dimmer channel must be operated by the DMX signal.
Auto：Random running.
Manual：Control by the menu [Manual Control].As the same of "DMX"
control, the shutter or dimmer channel must be operated manually.
Sensitivity: Use the menu to set desired response sensitivity from music.
Mixed Scene: Use the menu to set up the playback order of the scenes. Refer to the
document <User Program Guide> for more information.
Scenes Num.: Use the menu to set desired number of scenes for mixed playing
Scene Edit: Use the menu to edit scenes. Refer to the document <User Program Guide> for
more information.
Scene Index: Use the menu to select desired scene
Step Index: Use the menu to select desired step for the selected scene

13
Step Edit: Press into the edit interface.
Time: Set desired duration for the selected step (Unit 0.1 seconds, e.g. the
value of 123 is 12.3seconds）
Chn: Use the menu to select desired channel
Value: Set desired value of selected channel to meet selected step's needs.
Copy: Use the menu to copy the selected step in the selected scene
Paste: Use the menu to paste the copied step into the selected step in the selected
scene. (Please note that this operation will overwrite the targeted data!)
Record: Use the menu to record current DMX value and paste it into the selected step
in the selected scene.(Please note that this operation will overwrite the
targeted data!)
Lamp Power: The item allows to set desired power of the lamp
Following is the instructions of the menu options：
Eco：Economical mode. Lamp works in minimum rated power
Std：Standard mode. Lamp works in maximum rated power.(If the shutter
is closed, the power will work in minimum power automatically)
Black Out:
Pan/Tilt: Black-out while head moving
Color: Black-out while color changing
Gobo: Black-out while gobos changing
Time/Speed Mode:
Pan/Tilt: Use the menu to set the mode of pan/tilt movement
Following is the instructions of the menu options：
Speed：Both Pan and tilt will move with the same speed as adjusted at the
channel "Pan/Tilt speed, Pan/Tilt time"
Time：The Pan and Tilt will move with different speeds and they will come
at the same time to the end point of their tracks(pan and tilt use their optimal
speeds)
Rot.Gobo: Use the menu to set the mode of rotate gobo movement
Following is the instructions of the menu options：
Speed：Rot.gobo move in speed mode.
Time：Rot.gobo move in time mode.
Random Strobe Sync: This menu sets if synchronization between every device when
strobe in random mode.
Display Config: LCD display configuration
Sleep: Use the menu to select waiting times before sleep.
Brightness: Use the menu to select desired brightness
Reverse: Use the menu to set Inverted orientation if the fixture is hanging on the truss
Indicator: Use the menu to set lighting of indicators.

14
Following is the instructions of the menu options：
Auto: Sleep When screen sleep.
KeepOn: Lighting forever
Advanced:
Fine Adj: This is the factory adjustment function locked with password.
Factory Settings: Used in factory only，it requires the password to enter..
DMX Lost: Use the menu to select run mode when external DMX cannot be connected. This
is active on power-on only， if it detects DMX on power on， and then lost the signal，
it keep on the last DMX state。
Following is the instructions of the menu options：
Middle: The DMX of pan and tilt are set to 128, all other DMX are set to 0.
Keep：Keep the last state when reset finished.
Test (factory/gobo/color) ：Controlled by built-in program. Refer to the menu
“Run” for more information.
Music：
Controlled by the volume of the ambient sound. Use the menu [Running
Cnfg]-[Music Ctrl Cnfg] to set up the running mode and microphone sensitivity.
Program：Program：Controlled by User's program。User the menu [Running
Cnfg]- [Mixed Scene] and [Scene Edit] to set up or edit the scenes.
Quick Position: Use the menu to Automatically calculate the shortest path of color and
gobos to achieve rapid two-way positioning（that is，the Forward rotation over
180 degrees will Change to backward rotation less than 180 degrees）. When
"N" is selected, color and gobos only rotate in one direction.
Auto Gobos: If "Y" is selected, following rules is enforced:
Static gobos automatically switch to the big hole when the rotating gobos is
activated;
Static gobos and rotate gobos automatically switch to big hole when frost is
activated.
Fan Speed: Set the fan speed mode. This function is only valid on some models, please
refer to the specification for more information.
Language: Use the menu to select desired system language
Lamp Off: Use the menu to select what the motor should do when lamp is off. If ""No Act"" is
selected, lamp doesn't lead to any changes of motors. If "Sleep" is selected, motors
except Pan/Tilt will sleep when lamp is off.
Turn Off Bat: If the device is battery-powered (this function is valid only on some
models),you can turn off the battery immediately.
P/T Correction: Use the menu to select if activate the position auto correction function. This
function will optimizes performance, but if this function is out of action, the pan

15
or tilt motor will fails to work normally. If pan or tilt works abnormally, try stop
this function temporarily. Pan and tilt will run normally without this function but,
it will increase the amount of reset time, and cause more impacts between the
limit structures, and the positional errors will not be corrected automatically
when the step motors lose step. This menu option only take effect when reboot
the system.
Allow DMX save: If select "Yes"，the setting values from functions DMX channel(6/4/6) will
be saved to EEPROM, that is, The setting value will be retained for the next
time when you reboot the system(This menu selection is valid for all the
settings in the function channel except for the "Run mode").
Clear Lamp Time: Use the menu to reset the counter of operation hours with the lamp to 0,
when a new lamp replaces the old one.
Recover Setting: Use the menu to reset factory settings. But the information like fine tuning
of motor, lamp switch state, user programs, lamp on time, will not be
resettled.
Please note that do not perform this Operation when the motors is rotating
with high speed because it will tack relatively long time to write the EEPROM.
Info:
DMX Monitor: Display the DMX value from controller
Chn: Use the menu to select desired channel which you need to watch.
Value: Show the current value of the selected channel
State Monitor: Display current running status
CPU1 TEMP ℃:The menu shows the temperature of the CPU which is in the fixture
base.
CPU2 TEMP ℃:The menu shows the temperature of the CPU witch is in the fixture
head.
Lamp TEMP ℃:Shows the monitoring points temperature of the lamp. If the
temperature is lower than 0℃or there is no temperature sensor for
digital detection(temperature sensor is fitted on some models only),it
will shows "Invalid".
Battery (%): Shows the battery capacity in percentage (notes that only some models
are fitted with battery).
Lamp Service time: Lamp service time
ThisTime (m): The menu shows the total number of the operation minutes with the
lamp on currently.
Total(h):The menu shows the total number of the operation hours with the lamp on
since the last operation of clear.
Err State: Error information (If there is any error shown in this menu, a exclamatory mark will
show at the top right corner of menu cover)

16
EEPROM: This message will appear when EEPROM goes bad.
Sensor Err: The states of all of the sensors
Pan Raster: Is the position sensor (raster) error.
Tilt Raster: Is the position sensor (raster) error.
Pan Reset: Is the original position sensor error.
Tilt Reset: Is the original position sensor error.
Color wheel: Is the original position sensor error.
Sta.gobo: Is the original position sensor error.
RotGoboWheel: Is the original position sensor error.
Rot.gobo: Is the original position sensor error.
Focus: Is the original position sensor error.
Zoom: Is the original position sensor error.
Prism: Is the original position sensor error.
LampComm: The communication between CPU and lamp driver. If this
communication go out of work, the CPU cannot determine the lamp is on
or off, and some functions may be affected.
CPU2 Comm: This message informs you that the communication between the
display PCB in the fixture base and the motor driver PCB in the fixture
head failed, and cables may be broken.
Lamp Overheat: The Lamp is overheating and it should be turn off. Note that the
temperature digital detection only valid on some models. If there is no
temperature digital detection device，the lamp thermal protection was
realized by a mechanical Thermo Switch only.
CPU1 Overheat: This message informs you that the display PCB in the fixture base
had been overheated and the fan in the fixture base may be broken. If
the CPU if overheated, it will automatically restart or work abnormally.
CPU2 Overheat: This message informs you that the motor driver PCB in the fixture
head had been overheated and the fan in the fixture head may be
broken. If the CPU if overheated, it will automatically restart or work
abnormally.
Flash Err: There is a read or write error of the MCU flash memory. Please contact your
Dealer or Fabricator for repair assistance.
RAM Err: A memory allocation failure occurs. Please contact your Dealer or Fabricator
for repair assistance.
License Expired: The license has expired, please click the menu "Info" - "Time Left"
and input the serial number (SN) to continue using the device.
P/T Reference Speed: Shows the pan and tilt rotation time from start rotation to stop. This
time is for reference only,
Pan(.01s):Shows the pan rotation time from start rotation to stop.
Tilt (.01s):Shows the tilt rotation time from start rotation to stop.

17
Time Left(h):This menu shows how much permitted time（hour）have left. click to input the
serial number(SN) if needed.
Input SN.: Input the serial number to get the license for usage.
ID:Shows the ID of the device.
Product Code: This message informs you the product code of the firmware. It provide a
reference in maintenance only and the user can ignore them usually.
000-000-00-000-000-00: The code of firmware. The code shown here is just an
example, please refer to the machine for actual code.
15-12-8-143: Shows the EEPROM flag. The flag shown here is just an example,
please refer to the machine for actual flag.
Security settings: This menu is operated in factory only, the user may ignore it.
Test Mode: This menu is operated in factory only, the user may ignore it.
DMX Protocol
Mode/channel
DMX
value
Function
Type of
control
24
16
30
1
1
1
Pan
0-255
Pan movement by 540°
proportional
2
*
2
Pan Fine
0-255
Fine control of pan movement by 2.11°
proportional
3
2
3
Tilt
0-255
Tilt movement by 246°
proportional
4
*
4
Tilt Fine
0-255
Fine control of tilt movement 1°
proportional
5
3
5
Pan/Tilt speed
0
Max speed
step
Speed mode
1-255
Speed from max. to min.
proportional
Time mode
1-255
Time from 0.1 sec to 25.5 sec
proportional
6
4
6
Power/Special functions
0
Empty
To activate following functions, stop in DMX value
for at least 3s and shutter must be closed at least
3s(“Shutter/Strobe” channel 22/15/28 must be at
range:0-31 DMX). Corresponding menu items are
overwritten temporarily.

18
Mode/channel
DMX
value
Function
Type of
control
24
16
30
1-24
ECO mode（Lamp power 230W）
step
25-29
Standard mode（Lamp power 280W）
step
30-39
Rot. Gobo speed mode
step
40-49
Rot. Gobo time mode
step
50-59
Pan/Tilt speed mode
step
60-69
Pan/Tilt time mode
step
70-79
Blackout while pan/tilt moving
step
80-89
Disabled blackout while pan/tilt moving
step
90-99
Blackout while color wheel moving
step
100-109
Disabled blackout while color wheel
moving
step
110-119
Blackout while gobo wheel moving
step
120-129
Disabled Blackout while gobo wheel
moving
step
To activate following functions, stop
in DMX value for at least 3 seconds:
130-139
Lamp On, reset （ total reset except
pan/tilt）
step
140-149
Pan/Tilt reset
step
150-159
Color system reset
step
160-169
Gobo system reset
step
170-179
Dimmer/Shutter reset
step
180-189
Zoom/focus/prism reset
step
190-199
Reserved
200-209
Total reset
step
210-219
Synchronization of random strobe - On
220-229
Synchronization of random strobe - Off
230-239
Lamp Off
step
7
5
7
Color wheel
0-129
Continual positioning
proportional
130-189
Step Positioning
step
190-215
Forwards rainbow effect from fast to
slow
proportional
216-217
No rotation
step
218-243
Backwards rainbow effect from slow to fast
proportional

19
Mode/channel
DMX
value
Function
Type of
control
24
16
30
244-249
Random color selection by sound
control. The sensitivity is from Low to High
step
(set microphone sensitivity in menu :
Run Settings)
250-255
Auto random color selection from fast to
slow
proportional
8
*
8
Color wheel fine positioning
0-255
Fine positioning
proportional
9
6
9
Rot.Gobo shake
0
No shake
step
1-255
Shaking the gobo from slow to fast
proportional
*
*
10
Frost time
0
Function is off
step
1-255
Time of frost movement (0.1 sec. to 25.5
sec.)
proportional
*
*
11
Color time
0
Function is off
step
1-255
Time of color wheel movement (0.1 sec.
to 25.5 sec.)
proportional
*
*
12
Static gobo time
0
Function is off
step
1-255
Time of static gobo wheel movement (0.1
sec. to 25.5 sec.)
proportional
*
*
13
Prism time
0
Function is off
step
1-50
Time of prism movement (0.1 sec. to 5
sec.)
proportional
1-255
Time of prism rotation (0.1 sec. to 25.5
sec.)
proportional
*
*
14
Zoom time
0
Function is off
step
1-255
Time of zoom movement (0.1 sec. to 25.5
sec.)
proportional
*
*
15
Focus time
0
Function is off
step
1-255
Time of focus movement (0.1 sec. to 25.5 sec.)
proportional

20
Mode/channel
DMX
value
Function
Type of
control
24
16
30
10
7
16
Static gobo wheel
0-54
Gobos with no shake
step
55-199
Shaking gobos
proportional
200-201
Open/Hole
step
202-221
Forward gobo wheel rotation from fast to
slow
proportional
222-223
No rotation
224-243
backward gobo wheel rotation from slow
to fast
proportional
244-249
Random gobo selection by sound control.
The sensitivity is from Low to High
step
(set microphone sensitivity in menu :
Run Settings)
250-255
Auto random gobo selection from fast to
slow
proportional
11
8
17
Rotating gobo wheel
In the range of 0-59 DMX, the gobo
selection speed is controlled by the
Effect speed channel 21/*/27
0-102
Index– set indexing on channel 12/9/18
step
103-199
Rotation – set rotation on channel
12/9/18
200-201
Open/hole
step
202-221
Forward gobo wheel rotation from fast to
slow
proportional
222-223
No rotation
step
224-243
Backward gobo wheel rotation from slow
to fast
proportional
244-249
Random gobo selection by sound control.
The sensitivity is from Low to High
step
250-255
Auto random gobo selection from fast to
slow
proportional
12
9
18
Rot. gobo indexing and rotation
Gobo indexing – set position on
channel 11/8/17
0-255
Gobo indexing
proportional