Royston “L” UNIT User manual

MODULAR MERCHANDISING ASSEMBLY: “L” UNIT
A (1)
B (1)
F (1)
G (4)
P (2)
P (2)
I (2)
H (4)
E (1)
C (2)
D (1)
J (8) K (2)
L (2)
M (2)
N (8)
O (8)
PARTS:
Slatwall shown is optional

FASTENING LEGS ONTO BASE:
Turn base (B) upside down.
Slide leg into slot and line up holes.
1. ASSEMBLING LEGS:
Insert caps (G) into
leg (H) bottoms. G
H
2.
Using bolts
(N) and
nuts (O),
fasten legs
to base.
Clips (I) on back of base. Base, upright, with legs and clips attached.
B
H
If the unit will be positioned against
a “T” unit: Attach clips (I) to base as
shown on the opposite side from the
legs using the innermost bolt hole.
Note: Clips are not used if the unit
will be standing alone.
I
B
MODULAR MERCHANDISING ASSEMBLY: “L” UNIT

3. ASSEMBLING THE FRAME:
Insert Leveler parts (L & M)
into slot on bottom end of
Upright (C).
L
M
C
Insert one of the
Wire Grids (E)
into the channel
on Upright (C).
Note: the end of the Wire Grid must fit into the
hole at the bottom of the Upright channel.
Make sure the
horizontal wires that
are set close together
are at the bottom of
the unit.
Insert Screws (J)
into holes at top
and bottom of
Upright.
Insert Grid into
second Upright
channel, then
fasten with Screws
(J) as described
previously.
C
E
MODULAR MERCHANDISING ASSEMBLY: “L” UNIT

P
Frame
Slide section all the way to the bottom of the
channels and fasten using Screws (J).
Slide a section of the Flat Metal
Back (P) into the channels on
the back side of the frame.
Slide the next section of the
Flat Metal Back (P) into the
channels and fasten using
Screws (J).
P
P
Note: Flat Metal Backs are only one option.
Units may or may not be so equipped. However,
all back styles are attached in similar fashion.
4. FASTENING FRAME ONTO BASE:
Slide completed Frame onto Base as shown. Ensure the
ends of Uprights (C) slide into hooks on Base (B).
C
B
3. ASSEMBLING THE FRAME:
MODULAR MERCHANDISING ASSEMBLY: “L” UNIT

Secure Frame to Base using Screws
(K) at each corner, as shown.
5. ADDING KICKPLATE AND BASE SHELF:
Hook Kickplate (A) onto tabs on Base.
Base
C
A
F
Once Kickplate is in place, insert tabs
on Base Shelf (F) into first slots on
Uprights (C).
Lower Base Shelf (F) onto Base (B).
To level the Base Shelf (F), you need a
Level and Screwdriver.
Insert Screwdriver into holes on either side
of Base Shelf and adjust Leveler Screw (L)
as needed until upright is plumb, or with-
out the level, adjust to suit the end of the
“T” unit or wall condition.
MODULAR MERCHANDISING ASSEMBLY: “L” UNIT

Royston LLC One Pickroy Road Jasper, GA 30143 800.334.1766 770.735.3456 770.735.4017fax roystonllc.com
#10013659 ©Royston LLC. All rights reserved. 061016
6.
7.
ADDING TOP CAP:
Insert Top Cap (D) into locking tabs on either end of the frame.
Shelves can be added at either a right angle or 15 degree tilt.
Insert Plugs (P ) into each Upright (C),
and push completely down.
P
D
D
Locking Tabs
MODULAR MERCHANDISING ASSEMBLY: “L” UNIT