Ruffneck Defender XT-311 SPST User manual

ISO 9001
Defender®
Installation Instructions
Part No. 11936.Rev.1.02 August 2018
Thermostat for use in Hazardous Locations
Feed-thru Models: XT-311 SPST, XT-312 SPDT
22 Amps Res., 480VAC Max.; 1/2 HP @ 125VAC, 1 HP @ 250VAC
Class I, Divisions 1 & 2, Groups C & D; Class II, Division 1, Groups E,
F & G; Class II, Division 2, Groups F & G; Class III; Class I, Zones 1 &
2, Groups IIA & IIB.
Step 1
Mount thermostat approximately 5' (1.5m) above the oor where
average room temperature will be sensed and air circulates freely.
Keep thermostat away from hot and cold surfaces.
Step 2
Wire switch terminals as per Fig. 1 or 2.
Step 3
Install the cover using the 4 bolts supplied and tighten.
Step 4
Fill any unused conduit opening using plug supplied.
CAUTION
CAUTION. Electrician must have experience with
Hazardous Location equipment. Disconnect and lock off
power supply before wiring or servicing. All wiring must
comply with local codes and ordinances.
Installation Instructions
Models:
Feed-thru Models
XT-311 SPST
XT-312 SPDT
HEAT COOL COM.
213-TX1.GIF
L1
L2
HEAT COOL COM.
COOLING EQUIPMENT
sledoMllA2.GIF
11936.Rev.1.00
L1
L2
Thermostat for use in hazardous locations
Defender®
22 Amps Res., 480 VAC Max.; 1/2 HP @ 125 VAC, 1 HP @ 250 VAC Class I, Divisions
1 & 2, Groups C & D; Class II, Division 1, Groups E, F & G; Class II, Division 2, Groups
F & G; Class III; Class I, Zones 1 & 2, Groups IIA & IIB.
CAUTION: Electrician must have experience with Hazardous Location equipment.
Disconnect and lock off power supply before wiring or servicing. All wiring must comply
with local codes and ordinances.
1. Mount thermostat
approximately 5’ (1.5m)
above the floor where
average room temperature
will be sensed and air
circulates freely. Keep
thermostat away from hot
and cold surfaces.
2. Wire switch terminals as per
Fig. 1 or 2.
3. Install the cover using the 4
bolts supplied and tighten
4. Fill any unused conduit
opening using plug supplied.
5918 Roper Road
Edmonton, Alberta
Canada T6B 3E1
www.ccithermal.com
1-800-661-8529
PH: 780-466-3178
FX: 780-468-5904
[email protected]
®
Revision Date: October 2011
Installation Instructions
Models:
Feed-thru Models
XT-311 SPST
XT-312 SPDT
HEAT COOL COM.
213-TX1.GIF
L1
L2
HEAT COOL COM.
COOLING EQUIPMENT
sledoMllA2.GIF
11936.Rev.1.00
L1
L2
Thermostat for use in hazardous locations
Defender®
22 Amps Res., 480 VAC Max.; 1/2 HP @ 125 VAC, 1 HP @ 250 VAC Class I, Divisions
1 & 2, Groups C & D; Class II, Division 1, Groups E, F & G; Class II, Division 2, Groups
F & G; Class III; Class I, Zones 1 & 2, Groups IIA & IIB.
CAUTION: Electrician must have experience with Hazardous Location equipment.
Disconnect and lock off power supply before wiring or servicing. All wiring must comply
with local codes and ordinances.
1. Mount thermostat
approximately 5’ (1.5m)
above the floor where
average room temperature
will be sensed and air
circulates freely. Keep
thermostat away from hot
and cold surfaces.
2. Wire switch terminals as per
Fig. 1 or 2.
3. Install the cover using the 4
bolts supplied and tighten
4. Fill any unused conduit
opening using plug supplied.
5918 Roper Road
Edmonton, Alberta
Canada T6B 3E1
www.ccithermal.com
1-800-661-8529
PH: 780-466-3178
FX: 780-468-5904
[email protected]
®
Revision Date: October 2011
5918 Roper Road
Edmonton, AB T6B 3E1
1.800.661.8529
www.ruffneck.com

ISO 9001
Defender®
Instructions d’installation
Part No. 11936.Rev.1.02 août 2018
Thermostat pour utilisation dans les endroits dangereux
Modèles à traversée: XT-311 SPST, XT-312 SPDT
Rés. 22 amps, max. 480VAC; ½ HP à 125VAC, 1 HP, à 250VAC,
Class I, Divisions 1 & 2, Groupes C & D; Class II, Division 1,
GroupesE, F & G; Class II, Division 2, Groupes F & G; Class III;
ClassI, Zones 1 & 2, Groupes IIA & IIB.
Étape 1
Monter le thermostat à environ 5 pieds (1,5 m) du sol dans un
endroit où il mesurera la température moyenne de la pièce et où l’air
circule librement. Tenir le thermostat éloigné des surfaces froides et
chaudes.
Étape 2
Câbler les bornes d’interrupteur (voir la gure 1 ou 2).
Étape 3
Installer le couvercle à l’aide des 4 boulons fournis et le serrer.
Étape 4
Remplir toute ouverture de conduit non utilisée en utilisant le
bouchonfourni.
Installation Instructions
Models:
Feed-thru Models
XT-311 SPST
XT-312 SPDT
HEAT COOL COM.
213-TX1.GIF
L1
L2
HEAT COOL COM.
COOLING EQUIPMENT
sledoMllA2.GIF
11936.Rev.1.00
L1
L2
Thermostat for use in hazardous locations
Defender®
22 Amps Res., 480 VAC Max.; 1/2 HP @ 125 VAC, 1 HP @ 250 VAC Class I, Divisions
1 & 2, Groups C & D; Class II, Division 1, Groups E, F & G; Class II, Division 2, Groups
F & G; Class III; Class I, Zones 1 & 2, Groups IIA & IIB.
CAUTION: Electrician must have experience with Hazardous Location equipment.
Disconnect and lock off power supply before wiring or servicing. All wiring must comply
with local codes and ordinances.
1. Mount thermostat
approximately 5’ (1.5m)
above the floor where
average room temperature
will be sensed and air
circulates freely. Keep
thermostat away from hot
and cold surfaces.
2. Wire switch terminals as per
Fig. 1 or 2.
3. Install the cover using the 4
bolts supplied and tighten
4. Fill any unused conduit
opening using plug supplied.
5918 Roper Road
Edmonton, Alberta
Canada T6B 3E1
www.ccithermal.com
1-800-661-8529
PH: 780-466-3178
FX: 780-468-5904
[email protected]
®
Revision Date: October 2011
AVERTISSEMENT
AVERTISSEMENT. L’électricien doit détenir de
l’expérience avec l’équipement dans les endroits
dangereux. Déconnecter et verrouiller le câble
d’alimentation avant d’effectuer l’entretien ou le
câblage. Le câblage doit être conforme aux codes et
ordonnances locaux
Installation Instructions
Models:
Feed-thru Models
XT-311 SPST
XT-312 SPDT
HEAT COOL COM.
213-TX1.GIF
L1
L2
HEAT COOL COM.
COOLING EQUIPMENT
sledoMllA2.GIF
11936.Rev.1.00
L1
L2
Thermostat for use in hazardous locations
Defender®
22 Amps Res., 480 VAC Max.; 1/2 HP @ 125 VAC, 1 HP @ 250 VAC Class I, Divisions
1 & 2, Groups C & D; Class II, Division 1, Groups E, F & G; Class II, Division 2, Groups
F & G; Class III; Class I, Zones 1 & 2, Groups IIA & IIB.
CAUTION: Electrician must have experience with Hazardous Location equipment.
Disconnect and lock off power supply before wiring or servicing. All wiring must comply
with local codes and ordinances.
1. Mount thermostat
approximately 5’ (1.5m)
above the floor where
average room temperature
will be sensed and air
circulates freely. Keep
thermostat away from hot
and cold surfaces.
2. Wire switch terminals as per
Fig. 1 or 2.
3. Install the cover using the 4
bolts supplied and tighten
4. Fill any unused conduit
opening using plug supplied.
5918 Roper Road
Edmonton, Alberta
Canada T6B 3E1
www.ccithermal.com
1-800-661-8529
PH: 780-466-3178
FX: 780-468-5904
[email protected]
®
Revision Date: October 2011
Tous les modèles.
Équipement de refroidissement
CHAUFFAGE COM.REFROIDISSEMENT
CHAUFFAGE COM.REFROIDISSEMENT
Chauffages pour les environnements les plus rigoureux
MC
5918 Roper Road
Edmonton, AB T6B 3E1
1.800.661.8529
www.ruffneck.com