RV INSTALLATION
1. LOCATION
The Bluetooth Speaker Light is intended to be installed on the exterior of your RV. It
operates on 12V DC and the best place to fit it is in place of an existing awning light,
however you can install it anywhere outside or inside the RV as long as you can
connect it to 12V.
2. WIRING
Bluetooth Speaker Light is supplied with a power lead fitted with male &
female line plugs. These allow the speaker to be pre-wired and easily
connected by joining the two plugs together. The power plug also allows
for the connection ofthe optional 240V plugpack and allows the speaker
to be temporarily mounted if required.
Connection. Simply connect the red wire of the removable end of the
power lead to the RV’s +12V wire & the black wire to -12V. Ensure these
connections are made with suitable crimp terminals or solder & heatshrink.
3. MOUNTING
If installing in place of an exterior awning light, please use the following steps as a
guide:
1. Remove the existing awning light.
2. Mark the location of the 4 mounting screws. Note be careful to ensure the screws
will not damage any materials behind the mounting surface.
3. Mount the optional locating brackets using the centre screw (only) with the hook
part at the bottom. These brackets provide reinforcement for the speaker plus can
be used as a temporary, removable mounting option if required.
4. Connect the power plug to the socket that was wired in step three. Mount the
speaker using the 4 screws - taking care not to over tighten the screws. Please
ensure the power wire is recessed as much as possible in its hole where supplied
from; and ensure the rest of the cable is stored in the cavity at the back of the
speaker. Press in the supplied screw covers to hide the screws.
5. Using a suitable RV Sealant, seal around the edge of the speaker ensuring a
water-tight seal to complete the installation.
If you are unsure about any elements of these installation guidelines, please
seek the advice of an experienced RV installer or suitable Electrician.
INSTALLATION IN OTHER LOCATIONS
For installations in such as Marine, home Pergolas, Pool Areas and Entertainment
areas; please use the optional RV Media 12V Plug pack (p/n 040855) if a direct 12V
power source is not available.
Note the plugpack and any power connections must be located in a dry environment.
OPERATION
Powering the unit up.
To ensure easy operation, where the Bluetooth Speaker Light is fitted in place of an
awning light, use your RV awning light power switch to turn the Bluetooth Speaker
Light’s master power on or off. Where the Speaker Light
is fitted in other locations using an optional 240V plug
pack, please use this power supply to operate the unit.
The unit is fitted with an LED Light on/off switch on the
right-hand side of the (circled opposite) allowing you to
turn the LED light on or off as required.
BLUETOOTH CONNECTION
The RV Media Bluetooth Speaker Light connects to devices such as Smart Phones
using Bluetooth A2DP Audio Streaming technology.
1. When powered on, a red LED at the bottom of the Bluetooth Speaker Light will
indicate that it is switched on.
2. Within 3 seconds, the blue LED at the bottom of the speaker will illuminate to indicate
that the Bluetooth receiver is working.
3. If not connected to a Bluetooth transmitter such as Smart Phone or other Bluetooth
transmitting device, the unit will switch to “discovery” mode waiting for a Bluetooth
connection. The blue LED will flash quickly to indicate that the unit is awaiting
connection.
4. To connect to the speaker, open the Bluetooth menu on your device and search for
new devices. “RV Media” should be displayed as an available device. Select “RV
Media” to initiate connection.
Note you do not need to enter a PIN code to connect a device to this speaker.
5. The blue LED will illuminate to show the connection is in progress and if successful, it
will now flash every 5 seconds confirming the device is connected.
6. Only one device can be connected at a time but a maximum of 8 devices, once
paired, can be stored in memory. This means that a device previously paired will
automatically pair once the speaker is turned on providing the device is within range.
If, for example, a 9th device is paired with the speaker, the oldest device will be
erased and will need to be manually re-connected if used again.
7. Once connected to your device, you can then use you device’s Audio Controls to
start the music playback and control the speaker’s volume level.
8. Audio may also be streamed from many Smartphone apps such as Internet Radio
Stations, Youtube, Video Players etc. This feature is dependent on app & device |
capabilities, software and operation system version.
TROUBLESHOOTING
Most connection problems can be fixed by manually disconnecting & reconnecting your
Bluetooth device to the RV Media Bluetooth Speaker Light.
For updated Troubleshooting tips & information, please visit www.camec.com
Page 2 Page 3
First time use note. To ensure the Bluetooth Speaker Light remembers your
Bluetooth device, it may be necessary to manually disconnect your device from
the speaker on first use (this is done on your device’s BT menu). This will ensure it
is memorised and therefore should connect automatically for subsequent use.
Removable end.
