Ryval Hoops C554 Series User manual

C554 Series
ADJUSTABLE HEIGHT
GOAL SYSTEM
Version 4

2
Thank you and congratulations for purchasing a Ryval Hoops Goal
- the finest basketball goal system on the market today! You will
discover that Ryval Hoops is unsurpassed in product innovation, quality
and integrity in the basketball equipment industry. We are focused on
designing, engineering and products that meet and exceed expectations
of today’s toughest playing environments and demanding players.
Consider the following to determine where to install the basketball goal:
Whether the goal is to be installed into a landscaped area next to the
playing surface or into a hard-surfaced area.
Backboard size and its extension distance from the structures.
If court markings are to be used.
Amount of playing surface desired beneath the goal.
Other functions of playing surface (such as driveway, tennis court, etc.)
WWW.RYVALHOOPS.COM 1 - 8 0 0 - 7 8 7 - 0 6 5 5
3'0"

3
WWW.RYVALHOOPS.COM
1 - 8 0 0 - 7 8 7 - 0 6 5 5
Consult Ryval Hoops if you do not

4
WWW.RYVALHOOPS.COM 1 - 8 0 0 - 7 8 7 - 0 6 5 5
a. Dig a hole 48" deep and 21"x 21"square . The edge of the hole
should be flush with the edge of the playing surface. If you live in an area
where heavy frost can occur, it may pose a problem, consult your local
building inspector to determine the appropriate hole depth.
b. Build a form before pouring the concrete pad, to ensure that the top
of the concrete remains straight and square. The form should
be placed about 1/2" above the playing surface to allow for water drainage.
c. Bell out the bottom of the hole.
NOTE: The hole must be at least 48" deep.
NOTE: A square hole prevents the rotation of the concrete.
NOTE: The area behind the playing surface must be cleared off by at least
3 feet to enable the user to stand behind the pole to adjust the Rim height.
NOTE: At rim height 10 foot, distance from the face of backboard
to the front of Main Post (A) is 36". Use these specs to calculate
desired backboard overhang of driveway/court.
STEP A 21"
21"
48"

5
WWW.RYVALHOOPS.COM
1 - 8 0 0 - 7 8 7 - 0 6 5 5
STEP B
A. Thread a Hex Nut (U4) onto each of the J-Bolts (U2). Securely
tighten the Nuts all the way down to the end of the threads.
B. Slide the threaded end of the J-Bolts through the holes
in the Anchor Template (U1) and secure each J-Bolt with Hex Nuts
(U4) as shown. Securely tighten all Nuts at this time.
U2
U4
U1
U2
U2
U2
U4
U4 U4
U4
U2
NOTE: Make sure the curved“J”ends of the J-Bolts are
oriented in a rectangular pattern, as shown.
STEP C
a. Mix the concrete according to the instructions on the bags. Note that
a thicker mix of concrete will dry stronger than a thin mix. Pour the
concrete into the hole, stopping approximately 18 inches from the top
of the hole.
b. Insert the four pieces of Anchor Rebar (U5) into the hole, pushing each
piece firmly to the bottom of the hole. The four pieces should be
arranged in a square approximately 8 inches wide so that each piece of
rebar will be positioned next to the J-Bolts when the J-Bolt Template
is placed in the cement.
c. Finish filling the hole to the top with concrete. The top of the concrete
should reach just above the level of the top of the form.
P

6
5/8" and 3/4" Sockets or Wrenches
15/16" and 1-1/16" sockets or Wrenches
WWW.RYVALHOOPS.COM 1 - 8 0 0 - 7 8 7 - 0 6 5 5
STEP D
a. Position the J-Bolt Template (U1) over the hole so that it is centered,
with the sides of the plate square with the sides of the hole.
b.Push the J-Bolts (U2) into the concrete until the J-Bolt Template is
resting flat against the surface of the concrete.
c. Grasp the tops of the J-Bolts and agitate the Template assembly back
and forth repeatedly to eliminate any air bubbles in the concrete. Lift the
Template slightly above the concrete when agitating . Make sure the
Template is resting on the concrete after agitating. Form the concrete
into a downward slope away from the Pole to allow water runoff.
d. Clean off any concrete that may be on the J-Bolt Template or the exposed
portions of the J-Bolts.
e. Using a carpenter’
s level, make sure the Template is square to and level
with the playing surface.
f. Allow the concrete to cure for a minimum of 5-7 days before installing
the rest of your basketball system. In cold , wet weather or humid
climates, allow additional time for the concrete to cure.
YOU ARE NOW FINISHED WITH THE INITIAL ASSEMBLY STEPS. DO NOT PRO-
CEED WITH THE ASSEMBLY UNTIL THE CONCRETE HAS FULLY CURED . CUR-
ING WILL TAKE A MINIMUM OF 72 HOURS. IN HUMID CLIMATES OR WET
WEATHER, ALLOW ADDITIONAL TIME FOR THE CONCRETE TO CURE.
! !
WARNING
NEVER USE THE SYSTEM WITHOUT FOLLOWING THE CEMENTING INSTRUCTIONS . FAILURE TO
FOLLOW ALL OF THESE INSTRUCTIONS AND WARNINGS COULD LEAD TO SERIOUS PERSONAL INJURY
OR PROPERTY DAMAGE AS LISTED ON PAGE ONE.
U1
U2

PARTS LIST

,. '

.
  "
  DESCRIPTION
A  
B  
  
D  
  
  
  
  
  
  
K  
  
M  
N  

  
  
  
   
us  
  
RIM HARDWARE
  
22  
  
1-800- 78 7-0655
.

-�

  
  
  
' '





  
  





 
 
  
  
 
  
  
  
  
  



  
  
    










WWW. RYVALHOOPS.COM


WARNING:
Do not pass bolt
through cylinder
welded onto
backside of post.
Pass bolt through
hole on main post.
Pass
through
main post

Ryval Warranties
Buyer agrees that products sold by Ryval hoops carry the following warranty. Subject to
proper installation and normal, intended use, all structural components of Coach Series tm,
Phenom X Series tm, Wall Mount Hoops are warranted to the original owner to be free of
defects in materials and workmanship for the duration of ownership (Limited Lifetime) by
the original retail purchaser, subject to the limitations below. The Driveway Series tm will
be covered by this warranty for a period of 5 years. This limited warranty coverage is
extended only to the original retail purchaser and terminates if the original retail purchaser
otherwise transfers of sells the product. This warranty is limited to a repair or replacement of
the defective part. Product covered under this warranty will be shipped at the customer’s expense.
Ryval Hoops is not responsible for any expense associated with freight, or delivery and installation
of the warranted part(s). Ryval Hoops reserves the right to inspect all warranty claim parts for
which a claim has been made.
Any modification could damage the structural integrity of the equipment and voids all
warranties. Where listed as “Limited”, the warranties shall cover damage or failure that
occurs during the course of normal or intended use of the product. Normal or intended use
shall be described as activity that is necessary for the participation in the sport for which
the equipment is designed. Not covered is damage caused by deliberate hanging, multiple
player hanging, vandalism, non-basketball activities or any other activity that could be
regarded as abusive.
Padding Warranty: Multi-Purpose Backboard Edge Padding: One-year limited warranty.
Custom fit & Wrap around Pole Padding & Gusset Padding One-year limited warranty.
Net: One-year limited warranty
Not Covered By This Warranty
Any Products subjected to abuse, negligence, improper installation, vandalism, acts
of God, alteration of product or any other events beyond the control of Ryval Hoops.
Use in non-residential applications of glass backboards.
Paint or rusted parts. If rust begins, sand rust & loose paint, primer & paint with a
satin black. Touch-up kits are available.
Deterioration of product due to time or wear and tear.
Use in non-residential applications of Glass backboards.
Normal deterioration of products due to atmospheric conditions, weather, rust wear and
tear (including paint), or other causes that do not affect functional use are not covered by
Ryval Hoops warranties. All warranties are valid only when product is used in the
intended application and when installed according to Ryval Hoops instructions. Warranty
will be void if maintenance instructions in the owner’s manual are not followed, including
jack lubrication. If you did not receive an owner’s/instruction manual, please contact Ryval
Hoops and one will be sent to you.

Warranty Claims: A copy of the original invoice must be presented to initiate
warranty claim. A warranty claim form must be completed and photos submitted for any
item you wish to claim under warranty. If part to be warranty is requested, a “Return
Merchandise Authorization” (RMA) number will be required prior to shipping damaged
Product by original retail Consumer Purchaser with freight prepaid by consumer. If the
purchase was made through a dealer, warranties do not cover dealer service charges, labor
charges, freight or travel expense associated with replacement, repair or removal or
warranty item
This warranty is exclusive and expressly in lieu of all other warranties, expressed or
implied, including warranties of merchantability or fitness for use. Ryval Hoops
does not assume, or authorize any person to assume for us, any other liability in
connection with the sale of our products. If Ryval Hoops cannot disclaim or exclude
implied warranties under applicable law, then to the extent possible any claims under such
implied warranties shall expire or expiration or the applicable warranty period. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you, Ryval Hoops does not assume or authorize any person to
assume for us, any other liability in connection with the sale of our products. Ryval Hoops
shall not be liable for loss of use of the product or other consequential or incidental costs.
Expenses or damages incurred by the consumer or any other use.
To the maximum extent permitted by law, Ryval Hoops assumes no responsibility for
incidental or consequential damages, which may arise from the purchasers or use of our
equipment. Some states don not allow the exclusion or limitations of incidental or
consequential damage, so the limitation or exclusion may not apply to you. If any provision
of this warranty is invalid, void or unenforceable in any instance or respect, the
unenforceable provision will be severed and reformed to affect the intent of this limited
warranty to the maximum extent possible, and the remaining provisions shall continue in
full force and effect and shall be enforced to the full extent permitted by law.
Ryval Hoops reserves the right at any time to change product specifications or substitute
similar components. A limited lifetime warranty is effective for the duration of ownership
by the original retail purchaser or 5 years after discontinuation of the product by Ryval
Hoops.
This warranty gives you specific rights and you may also have other rights, which vary
from state to state.
Questions or Comments?
www.RyvalHoops.com
Email: [email protected]
Phone [phone]