S.R.Smith rogue2 Instruction manual

06-820 APR16
ROGUE2
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
SRS AUSTRALIA, PTY LTD
12 Enterprise St
Richlands QLD 4077
Australia
Phone [phone] • Fax [phone]
www.srsmith.com/au
S.R. SMITH, LLC
CORPORATE HEADQUARTERS
P.O. Box 400 • 1017 S.W. Berg Parkway
Canby, Oregon 97013
USA
Phone [phone] • Fax [phone]
www.srsmith.com
S.R. SMITH ROGUE2 SLIDES ARE MANUFACTURED FOR INSTALLATION
AND USE ON RESIDENTIAL INGROUND SWIMMING POOLS ONLY. THE
ROGUE2 IS NEVER TO BE INSTALLED AND USED ON ABOVEGROUND
POOLS, ONGROUND POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING
DOCKS OR PLATFORMS OR OTHER BODIES OF WATER SUCH AS
LAKES
,
PONDS
,
RIVERS
,
ETC.

2
TABLE OF CONTENTS
INTRODUCTION ........................................................................................................................................... 3
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST ..................................................... 4
MAINTENANCE INSTRUCTIONS ................................................................................................................ 4
ASSEMBLED ROGUE2 LAYOUT ................................................................................................................ 5
PARTS LIST .................................................................................................................................................. 6
ASSEMBLY INSTRUCTIONS ....................................................................................................................... 8
Tools Required .......................................................................................................................................... 8
Rogue 2 Assembly ................................................................................................................................... 8
SLIDE DECK ANCHOR FLANGE PARTS LIST (SOLD SEPERATELY) ................................................... 14
ON-DECK MOUNTING INSTRUCTIONS ................................................................................................... 15
IN-DECK MOUNTING INSTRUCTIONS ..................................................................................................... 16
SLIDE PLUMBING INSTRUCTIONS .......................................................................................................... 17
GARDEN HOSE ADAPTOR INSTALLATION INSTRUCTIONS ................................................................ 18
ELECTRICAL BONDING ............................................................................................................................ 18
MANUFACTURER’S PLACEMENT INSTRUCTIONS ............................................................................... 19
APPENDICES: ROGUE2 SLIDE FOOTPRINT ............................................................................................ A
Visit srsmith.com for information on the complete line of
S.R.Smith pool products.
SLIDE ASSEMBLY AND INSTALLATION VIDEOS AVAILABLE AT
www.youtube.com/srsmithllc
REGISTER YOUR S.R. SMITH PRODUCT AT
www.srsmith.com/en/customer-service/product-registration

3
INTRODUCTION
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE
OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.
THE ROGUE2 SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON
INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND
POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES
OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE,
AND SUPERVISION ARE ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF
SERIOUS INJURY OR DEATH.
ALL NATIONAL AND LOCAL BUILDING CODES MUST BE FOLLOWED. THIS INCLUDES ANY
APPLIABLE REQUIREMENTS FOR SIZE OF CONCRETE FOOTING, OVERALL HEIGHT OF SLIDE,
AND BODING OR ELECTRICAL CODES.
CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING
ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS
LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY
THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN
TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE
OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY
AFFECT THE SAFETY OF THE USER.
INSTALLER MUST GIVE TO SLIDE OWNER: ROGUE2 SLIDE INSTALLATION AND OWNER’S
MANUAL, THE WARRANTY CARD, AND ANSWER ALL QUESTIONS REGARDING SAFE AND
PROPER USE AND SLIDE MAINTENANCE.
FOR COMPLETE SLIDE SAFETY INFORMATION REFER TO THE OWNER’S MANUAL.

4
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST
Installer to review with slide owner upon completion of slide installation.
1. Inspect the runway for visible cracks or tears.
2. Inspect the ladder for sharp edges, protrusions, cracks, or tears.
3. Inspect all fasteners to make sure they are fully tightened.
4. Inspect the ladder for rigidity and attachment.
5. Measure the following dimensions and compare with the manufacturer’s placement instructions on
page 19.
 Pool water depth at the base of the slide should be at least 3’ (914 mm) deep, and at 4’6”
(1.372 M) out from slide exit, should be at least 4’6” (1.372 M) deep.
 The height of the slide runway exit above the water should be 20” (0.508 M) maximum.
 The distance between the slide centerline and the edge of other pool equipment should be at
least 3’6” (1.067 M).
6. Observe the position of the exit of the slide as shown in FIGURE O, FIGURE P, and FIGURE R on
pages 19 and 20.
MAINTENANCE INSTRUCTIONS
1. When hosing down the deck, hose your Rogue2 to wash away any dust, dirt or other debris, which
may have accumulated.
2. Be sure that all connections are secure. Tighten hardware if necessary.
3. All polyethylene parts require little maintenance. Hose and wipe to clean.
While cleaning slide, check and see that all nuts and bolts are tight and secure.
4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.
5. Inspect all attachment points for loose or corroded fasteners.
6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue in
the ladder steps, rails, or attachments means. Yield is evidenced by crystallization or fine cracking of
the ladder tread and/or surface.
7. Inspect the ladder handrails for rigidity and attachment.

5
ASSEMBLED ROGUE2 LAYOUT
ROGUE 2 right curve slide shown, left curve is mirror image of right curve.
See Appendices for additional slide layout details.
FIGURE A

6
PARTS LIST
Item Number Description Quantity
1 Garden Hose Adapter (ref. pg 13) 1ea.
2 1” PVC 90 Elbow ST SCH 40 SXS 1 ea.
3 Plastic Pipe Clamp for 1” SCH 40 6 ea.
4 PVC Ball Valve SCH 80 SXS 1 ea.
5 ¼-20 x 6” Carriage Bolt S/S 4 ea.
6 ¼-20 x 8” Carriage Bolt S/S 2 ea.
7 Aluminum Handrail Spacer 6 ea.
8 Nylon Handrail Connector 8 ea.
9 Nylon Tube Connector 6 ea.
10 1/4 x 5/8 Flat Washer 13 ea.
11 ¼” Lock Washer S/S 8 ea.
12 ¼-20 Hex Nut S/S 8 ea.
13 Aluminum Ladder Spacer 2 ea.
14 3/8-16 X 5" B.H.C.S. 18-8 S/S FULL-THREAD (TT) 2 ea.
15 HHCS 3/8-16 X 3.5" S/S 2 ea.
16 3/8” x 3.5” Button Head Cap Screw S/S 4 ea.
17 3/8” Flat Washer S/S 16 ea.
18 3/8” Lock Washer S/S 8 ea.
19 3/8” Hex Nut S/S 4 ea.
20 3/8-16 ACORN NUT 316 S/S HIGH Crown 4 ea.
21 5/16 Hex Washer Head Tek Screw S/S 4 ea.
22 Self Tapping Screw #10-16 x 1” S/S 6 ea.
23 Vinyl Cap .172 ID x .5 LG. 6 ea.
24 ¼” X ½” Sheet Metal Screw 5 ea.
* Hose PVC Flex, 8 ft. (not shown in Figure 1) 8 ft.
25 Bolt Cap .250 ID x .5 LG Vinyl 6 ea.
26 Gasket .5” Thick x .5” Wide (Not Shown) 4.6 ft.
27 1” Coupler SCH 80 PVC (Not Shown) 1 ea.
Visit srsmith.com for hardware kit and replacement part information.

7
(24)
(25)

8
ASSEMBLY INSTRUCTIONS
Tools Required
1. PVC glue
2. 7/32” Allen Wrench
3. Electric Drill, Phillips Drive, ½ Hex Socket Drive
4. Ratchet with 7/16”, 1/2" and 3/8” sockets
5. 7/16”, 1/2” and 9/16” wrench
6. Hammer drill with 1/4" (6 mm) masonry bit
7. Small Level
8. Tape
9. 9/16” Deep Socket
10. 3/8” (9.5 mm) Drill Bit
11. ¼” (6 mm) Drill bit
12. Pencil or marker
13. Loctite® 242 Thread Locking Compound
Rogue 2 Assembly
1. Place the slide runway upside down on a surface that will not scratch the slide.
(TIP: Use flattened Rogue2 box to help protect slide from scratches
during assembly.)
a. Ensure the gaskets installed at the factory are
still in place. Any damaged gasket should be
replaced prior to assembly.
b. Use Anti-Seize on all hardware pieces to
prevent galling of the stainless steel.
c. Begin by installing the hardware through the
outside rails of the runway. Insert a (#14) 5”
Button Head Screw with a (#17) Flat Washer
though each side rail as shown in Figure 4.
Fasten each screw using a (#17) Flat Washer,
(#18) Lock Washer, and (#19) Hex nut. Do not
fully tighten at this point.
19
18
17
17
14
15,17
17
,
18
,

FIGURE B

9
d. Next, insert the hardware through the holes in the bottom of the runway parts. Insert a
(#15) 3.5” Hex Head Screw with a (#17) Flat Washer though each hole as shown in
Figure 4. Fasten each screw using a (#17) Flat Washer, (#18) Lock Washer, and (#19)
Hex nut.
e. Go back and fully tighten the outside bolts before completely tightening the center bolts.
Tighten until the plastic surfaces come into contact and are secure. Do not over tighten
the hardware.
2. Insert the slide legs into the leg sockets. See FIGURE C.
a. The two short legs go into the front sockets nearest the slide exit.
b. The shorter of the two longer legs goes into the socket on the inside curve of the slide.
c. Be sure to insert the end of the legs that do not have the pre-drilled holes into the leg
sockets.
d. Do not attach the legs permanently at this point.
e. Tape the legs to the leg sockets so that they will be held in place when turning the slide
upright.
3. Insert the top of the slide
ladder all the way into the two
sockets in the slide. Use
clamps to temporarily hold the
ladder in place while the slide
is being turned upright. See
FIGURE D. NOTE: The top
of the ladder is the end with
the side rails cut square.
FIGURE C
Guideslots
FIGURE D

10
4. Carefully turn the slide with the legs and ladder upright for setup. It will be necessary for two
people to perform this to avoid damage to the slide.
5. Place the slide at the desired location relative to the pool wall. See MANUFACTURER’S
PLACEMENT INSTRUCTIONS on page 19.
6. Temporarily remove the clamps to make final adjustments to the ladder.
a. Make sure that the slide entrance is level from side to side while maintaining a height of
77” + 1/2” (1.9558 M + 12.7 mm) from the deck level, and a ladder angle of 15 deg.
(0.262 rad) with respect to the vertical. See FIGURE A for reference.
b. Reattach clamps to hold the ladder in place prior to drilling.
7. Drill two 3/8” (9.5 mm) diameter holes through each of the ladder side rails using the holes in the
slide as a drill guide. See FIGURE E
Levellefttoright
Andadjustclamps
DRILL3/8”BITx4
Places
17
,
18
,
20
17
,
16
For SI: 1 degree = 0.017 rad
FIGURE E

11
8. Secure the ladder to the slide using the hardware as shown in FIGURE E. Insert a (#16) 3.5”
Button Head Screw with a (#17) Flat Washer though each drilled hole. Fasten each screw using
a (#17) Flat Washer, (#18) Lock Washer, and (#20) Acorn Nut.
9. With the entrance way secured and the slide in relative final position. Level as close as possible
the exit runway surface horizontally, from side to side, using a small level. The exit end height
should be maintained at 7” (0.178 M) between the bottom of the slide and the deck, see FIGURE
A
10. The legs can be adjusted up and down within the leg sockets to help adjust for level. Once the
slide is properly leveled the legs shall be permanently attached by drilling a 1/4" (6 mm) hole into
each leg using the hole on the leg socket as a guide and fastening with a (#21) 5/16” Hex Head
Washer Tek Head Screw. See FIGURE F.
Step3.
x4Places
Step2.
Step3.
FIGURE F

12
11. Disassemble each handrail as shown in FIGURE G. Insert the two handrails into the holes on the
top of the slide runway rails, and rotate so that the rails are resting in the grooves on the back
side of the entrance section. Secure each handrail into the socket using a (#10) Flat Washer, a
(#11) Lock Washer, and a (#12) Hex Nut. Use Loctite® 242 Thread Locking Compound on all
handrail fasteners.
12. Starting with the top handrail spacer, align the top hole in the handrail with the top hole in the
ladder side rail. Next, assemble the handrail spacer parts (#7), (#8) and (#9) in the order shown
in FIGURE G and align it between the handrail and ladder top holes. Next, insert the (#6) 1/4-20
x 8” Carriage Bolt through the handrail and the handrail spacer parts. The (#13) Ladder spacer is
to be placed in the inside channel of the ladder side rail such that the (#6) Carriage Bolt holds it in
place after it is pushed completely through the ladder side rail, see FIGURE H. Secure the (#6)
Carriage bolt using a (#10) Flat Washer, a (#11) Lock Washer, and a (#12) Hex Nut in the order
shown in FIGURE G and FIGURE H. Use Loctite® 242 Thread Locking Compound on all
handrail fasteners.
FIGURE G
8,7,9,13,10,11,
6
5
5
8
,
7
,
9
,
10
,
11
,
12
8
,
7
,
9
,
10
,
11
,
12
10
11
12

13
13. For the remaining two ladder spacers, align parts (#7), (#8) and (#9) between the hole in the
handrail and the hole in the ladder as in step 12. Use a (#5) 1/4-20 x 6” Carriage Bolt along with
a (#10) Flat Washer, a (#11) Lock Washer, and a (#12) Hex Nut to fasten the parts together as
shown in FIGURE G and FIGURE H. Place (#25) Vinyl Cap over the exposed threaded ends of
the bolts. Use Loctite® 242 Thread Locking Compound on all handrail fasteners.
FIGURE H
InsertSpacer(13)
10
,
11
,
12
,
25
10
11
12

14
SLIDE DECK ANCHOR FLANGE PARTS LIST (SOLD SEPERATELY)
Item Number Part Number Description Quantity
1 75-209-5000 Aluminum Flange Anchor 4 ea.
2 05-162 5/16 -18 UNC x 2 3/4 STUD w/ FLAT WASHER & LOCK NUT 16 ea.
3 05-14-123 1/4-20 UNC x 2 3/4 HHCS 4 ea.
4 04-14-111 1/4"ID x 5/8"OD FLAT WASHER 8 ea.
5 05-14-117 1/4-20 UNC HEX NYLON LOCK NUT 4 ea.
6 01-500 3/8" O.D. ALUMINUM BUSHING 4 ea.
7 800-1110 5/16” SPLIT LOCK WASHER 316 SS 16 ea.
FIGURE I

15
ON-DECK MOUNTING INSTRUCTIONS
For In-Deck Mounting proceed to Step 19
1. Bond slide per local codes (see ELECTRICAL BONDING page 18).
2. Place a deck anchor flange over each end of the slide legs.
3. Using the four holes on each flange as a template (see FIGURE I), mark the location of each hole
on the deck, Next, drill a 5/16” (7.9 mm) diameter by 1-7/8” deep hole at each marked location.
CAUTION: Do not drill holes larger than 5/16” (7.9 mm). Maintain drill hole straight and
perpendicular for proper holding strength of anchor stud.
4. Raise the flange up the leg and secure in place while using a hammer to drive the (#2) 5/16”-
18UNC x 2-3/4” Anchor Stud, with a (#2) 5/16” Hex Nut on top, into the hole leaving 7/8 of an inch
(22.2 mm) of the stud above the deck. Then tighten the nut until it is flush with the deck. Then,
tighten the nut approximately three turns to set the anchor stud. Finally, remove the nuts.
5. Secure the four flanges with (#2) 5/16” Flat Washers, (#7) 5/16" Lock Washers and the (#2)
5/16"–18UNC Hex Nuts.
6. Using the center holes on each ladder foot as templates, mark the hole locations on the deck.
Next, drill holes 5/16" (22.2 mm) diameter by 2-1/4 inches (57.1 mm) deep and secure (#2)
Anchor Studs as described in 3 & 4 above.
7. Secure the two ladder feet with (#2) 5/16” Flat Washers, (#7) lock washers, and the (#2) hex nuts.
Be sure that the ladder maintains 15 degrees (0.26 radians) from vertical.
8. Drill a 1/4" (6.3 mm) diameter hole into the slide leg through the 3/8” (9.5 mm) diameter hole in
the flange. Insert the (#6) 3/8” O.D. Aluminum Bushing into the hole in the deck flange and push
in until it contacts the slide leg. Now insert the (#3) 1/4"-20UNC x 2-3/4” Hex Head Cap Screws
and (#4) 1/4" x 5/8” Flat Washers through the bushing and in about a 1/2" (12.7 mm) into the hole
in the slide leg. With the cap screw in position, drill a 1/4" hole into the slide leg through the 5/16”
(7.9 mm) diameter hole in the opposite side of the deck flange. Take care not to run the drill bit
into the 1/4" bolt. Push the cap screw completely through the slide leg. Install the (#4) 1/4" x 5/8”
Flat Washers and (#5) 1/4"-20UNC Hex Lock Nuts

16
IN-DECK MOUNTING INSTRUCTIONS
9. Insert 3/8” (9.5 mm) diameter rebar (not provided) into the holes located at the bottom of each leg
making sure that the rebar will be a minimum of three inches (3”) below the deck surface.
10. Bond slide per local codes (see ELECTRICAL BONDING page 16).
11. Secure the ladder so that the ladder steps are level, from side to side, and the ladder is held at
15 degrees (0.26 radians) from vertical.
12. Secure the slide to prevent the movement during the concrete pour to ensure that the slide
position remains the same.
13. SUGGESTION: To ensure easy removal of concrete from legs and ladder, wax or wrap with wax
paper approximately 12 inches (0.305 M) above deck level.
14. Proceed with pouring the concrete deck and finish as desired. Let concrete cure per concrete
manufactures directions before using slide.

17
SLIDE PLUMBING INSTRUCTIONS
1. Use a drill with a Phillips bit to fasten the (#3) Plastic Pipe Clamp to the ladder as shown below in
Figure 12. The hose clamp should be attached with the top of the clamp aligned with the top of
the step and the side of the clamp against the ladder side rail,
See FIGURE J. Place (#6) Vinyl Cap over the tip end of the
screw. Repeat this step for each tread on ladder.
2. Install the (#2) PVC 90˚ Elbow fitting onto one end of the PVC flex hose using PVC
glue. Next apply glue to the male end of the (#2) Elbow fitting and the female fitting
that is pre-installed in the slide. Connect the (#2) Elbow fitting and hose assembly to
the slide while ensuring that the elbow fitting is oriented so that the hose is aligned
with the hose channel in the bottom of the slide. See FIGURE J and FIGURE K.
Entrance piece hose
channel for plumbing
2
2
3
FIGURE J
Installtheflex
hoseandstring
itthroughthe
clamps.
2
FIGURE K

18
3.
Starting with the top hose clamp, insert the PVC hose into
the clamps. The clamps automatically tighten when pressure
is applied pushing the hose into the clamps.
4. Apply PVC glue to one socket of the (#4) PVC Ball Valve
and insert the PVC hose into the valve as shown in FIGURE
L. Allow the glue sufficient time to dry. The final step is
joining the PVC Ball Valve to the water source.
GARDEN HOSE ADAPTOR INSTALLATION INSTRUCTIONS
If connecting the Rogue2 water system to the pool plumbing system is not an option you may connect the
water system to a garden hose by following the steps outlined below.
1. Make sure that the Rogue2 water system has been properly assembled as explained in the
Rogue2 Installation Instructions. Next, apply PVC glue around the end of the garden hose
adapter indicated by the arrow in FIGURE M.
2. After the glue is applied quickly insert the PVC
fitting into one end of PVC ball valve as shown in
FIGURE N
3. The final step is to thread a garden hose into the
PVC garden hose adapter.
4. After connecting the water source to the ball valve, turn
on water slowly to check for leaks
ELECTRICAL BONDING
If electrical bonding is required by the local governmental regulations, it shall be done in accordance with
Article No. 680 of the current National Electrical Code or the local Code, whichever has jurisdiction. Five
(#24) 1/4" x 1/2" Sheet Metal Screws and five (#10) 1/4" x 3/4" Flat Washers are provided for this
purpose. Secure one per slide leg and one per ladder.
4
1
FlexHose
FIGURE L
FIGURE M
FIGURE N

19
MANUFACTURER’S PLACEMENT INSTRUCTIONS
PROPER ASSEMBLY, INSTALLATION, USE, AND SUPERVISION ARE ESSENTIAL FOR PROPER
OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY.
1. The critical dimensions for placement of the Rogue 2 are as shown in FIGURE O and FIGURE P.
A. The slide exit runway surface shall not exceed 20” (0.508 M) above the water surface and not
less than 8” (0.203 M) above the deck/coping surface (see FIGURE O)
B. The slide shall be positioned so that all water flowing off the runway exit drops into the pool.
C. The minimum depth of water below the exit lip of the slide shall be 3’ (0.914 M) and increases
to 4’-6” (1.371 M) at Pt. A which is a distance of 4’-6” (1.371 M) from the exit lip of the slide.
(See FIGURE O).
D. A minimum depth of 4’-6” (1.371 M) shall be maintained at a distance of 9’ (2.743 M) along
the extended centerline of the slide from Pt.A. (See FIGURE O).
2. A minimum clearance area in front of the slide shall be maintained at all
times as follows:
A. A minimum clearance area in front of the slide shall be maintained
away from the coping, another slide, a diving board or a rope and
float line. (See FIGURE P). The minimum clearance distance on
either side of the extended centerline of the slide runway shall not
be less than 3’-6” (1.067 M) at a point no less than 2’-6” (0.762 M)
from the exit of the slide and extending a distance of 13’-6” (1.445
M) in front of the slide. (See FIGURE P)
B. The minimum clearance area in front of a properly installed diving
board on an inground swimming pool is a minimum distance of 3’-
6” (1.067 M) on either side of the board’s centerline as shown in FIGURE Q. Pt.C
extends a minimum distance of “C” from the tip end of the board as shown in FIGURE Q.
The width distance “W” on either side of Pt.C is given in TABLE 1 and shown in FIGURE Q.
FIGURE O
FIGURE P
DECK/COPING SURFACE
3' MIN.
EXIT
RUNWAY SURFACE
PLUMBLINE
20" MAX.
WATER LEVEL
ENTRANCE
Pt.A
13'-6" MIN.
9' MIN. 4'-6"
4'-6" MIN.4'-6" MIN.

20


C. The minimum clearance area of a slide of diving board shall not intersect any coping or rope
and float line as shown in FIGURE R. The minimum clearance area of a slide or diving board
may intersect each other provided that they are not used simultaneously.



See Article 5 contained in ANSI/APSP/ICC-5 2011 STANDARD
FOR RESIDENTIAL INGROUND SWIMMING POOLS and refer
to FIGURE 3 and Table 1 for Minimum Water Envelope
Dimensions AB, BC and Width at Point C.
TABLE 1
Board Minimum Clearance Area
Pool Type “C” Dimension “W” Dimension
I 14’ -6” (4.420 M) 5’ -0” (1.524 M)
II 14’ -6” (4.420 M) 6’ -0” (1.829 M)
III 16’ -6” (5.029 M) 6’ -0” (1.829 M)
IV 18’ -6” (5.639 M) 7’ -6” (2.286 M)
V 21’ -0” (6.401 M) 7’ -6” (2.286 M)
FIGURE Q
“C” DIMENSION FOR BOARD = AB + BC
“W” DIMENSION FOR BOARD = WIDTH AT PT.C
FIGURE R