S.R.Smith VORTEX User manual

06-197 S.R. SMITH, LLC 2010 FEB2015
THE VORTEX®
CORPORATE HEADQUARTERS
WESTERN SALES AND MANUFACTURING PLANT
P.O. Box 400  1017 SW Berg Parkway
Canby, Oregon 97013
Phone: [phone]  Fax: [phone]
www.srsmith.com
SLIDE OWNER’S MANUAL

2
Table of Contents
SLIDE WARNING AND SAFETY SUMMARY ................................................................ 2
INTENDED USE INSTRUCTIONS .................................................................................. 3
INSTALLED VORTEX STRUCTURAL & INSTALLATION CHECKLIST ....................... 4
DAILY/WEEKLY MAINTENANCE OF THE VORTEX .................................................... 4
APPLICABLE STANDARDS AND CODES ................................................................... 5
ASSEMBLY AND INSTALLATION ................................................................................ 5
DRAWINGS .................................................................................................................... 5
SUBSEQUENT OWNERS .............................................................................................. 5
MANUFACTURER’S PLACEMENT INSTRUCTIONS ................................................... 6
CLEANING INSTRUCTIONS .......................................................................................... 8
SLIDE WARNING AND SAFETY SUMMARY
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS AND THE
OWNER’S MANUAL MAY RESULT IN SEROUS INJURY OR DEATH
HEAD FIRST SLIDES ARE STRICTLY PROHIBITED
TO REDUCE THE POSSIBILITY OF INJURY, IT IS NECESSARY THAT THE USER
KNOW THAT THE CHIEF DANGER OF HEAD FIRST SLIDING IS SERIOUS SPINAL
INJURY. INJURIES TO THE SPINE MAY RESULT IN TEMPORARY OR
PERMANENT PARALYSIS OR EVEN DEATH. RESEARCH STUDIES HAVE
SHOWN THAT YOU CANNOT RELY ON THE WATER TO SLOW YOU DOWN
SUFFICIENTLY TO AVOID INJURY.
DO NOT SLIDE HEAD FIRST
DO NOT SLIDE HEAD FIRST

3
INTENDED USE INSTRUCTIONS
THE VORTEX™ SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION
AND USE ON INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THE
VORTEX SLIDE ON ABOVE GROUND POOLS, HOUSEBOATS, BOAT DOCKS,
FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF WATER SUCH AS
LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE, AND
SUPERVISION IS ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE
RISK OF SERIOUS INJURY OR DEATH.
1. SLIDE FEET FIRST ONLY AS SHOWN IN FIGURE 1. DO NOT SLIDE HEAD
FIRST
2. DO NOT JUMP OR DIVE FROM ANY PART OF THE SLIDE.
3. NO ROUGHHOUSING OR HORSEPLAY ON SLIDE.
4. CHILDREN MUST BE SUPERVISED BY AN ADULT AT ALL TIMES WHEN
USING THE SLIDE.
5. ONLY ONE PERSON ALLOWED ON THE SLIDE AT A TIME WITH A
MAXIMUM USER WEIGHT OF 325 LB.
6. HOLD ONTO HANDRAILS AT ALL TIMES WHEN USING THE LADDER.
7. FAMILIARIZE YOURSELF WITH THE SHAPE OF THE POOL BOTTOM AND
THE WATER DEPTH BEFORE YOU SLIDE. SLIDE FEET FIRST ONLY.
8. DO NOT SLIDE UNTIL ALL SUBMERGED OBSTACLES; SURFACE OBJECTS
OR OTHER SWIMMERS ARE CLEAR OF THE SLIDER’S PATHWAY.
9. STAY CLEAR OF THE SLIDE RUNWAY EXIT WHILE SWIMMING.
10. DO NOT USE THE SLIDE WHILE UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS.
11. DON’T SLIDE ALONE; USE THE BUDDY SYSTEM.
12. TAKE YOUR TIME IN PREPARING TO SLIDE. MOVE FORWARD SLOWLY
AND GET YOURSELF POSITIONED PROPERLY BEFORE STARTING THE
SLIDE.
13. ONLY PERSONS HEALTHY ENOUGH FOR WATER ACTIVITIES SHOULD
USE THE SLIDE. PERSONS WITH MEDICAL CONDITIONS, INCLUDING
PREGNANCY, SHOULD CONSULT THEIR DOCTOR BEFORE USING THE
 READ AND FOLLOW ALL SAFETY RULES
LISTED BELOW.
 MAKE SURE THAT EVERYONE WHO USES
THE VORTEX KNOWS AND FOLLOWS ALL
RULES.
 CHILDREN MUST BE SUPERVISED BY AN
ADULT AT ALL TIMES WHEN USING THE
SLIDE.

4
SLIDE. PERSONS WITH PHYSICAL DISABILITIES SHOULD USE CAUTION
AND MAY REQUIRE ASSISTANCE.
14. DO NOT USE THE SLIDE IF ANY PART OF IT BECOMES DAMAGED,
WEAKENED, OR BROKEN. HAVE THE SLIDE INSPECTED AND, IF
NECESSARY, REPAIRED BY A POOL PROFESSIONAL, WHO IS FAMILIAR
WITH WATER SLIDES BEFORE USING THE SLIDE. SEE INSTALLED SLIDES’
STRUCTURAL & INSTALLATION CHECKLIST.
PROPER SLIDING POSITION
Slide users must use the sitting slide position, facing forward, feet first as shown in
Figure 1.
INSTALLED VORTEX STRUCTURAL & INSTALLATION CHECKLIST
After installation and prior to the first use of the VORTEX and periodically (see
DAILY/WEEKLY MAINTENANCE OF THE VORTEX) thereafter the owner must:
1. Inspect the runway for visible cracks or tears.
2. Inspect the ladder for sharp edges, protrusions, cracks or tears.
3. Inspect ladder and pedestal mounting areas for loose or corroded fasteners.
4. Measure the following dimensions and compare with the Manufacturer’s
Placement Instructions on pages 6 AND 7.
 Measure the depth of water in front of the slide exit. (4-6”) min. depth at a
distance of (4-6”) from exit end of slide.
 Measure the height of the slide runway exit above the water. (20” max.)
 Measure the distance between the slide centerline and the edge of other
pool equipment.
5. Observe the position of the exit of the slide as shown in Figures 2, 3 and 5 on
pages 6 and 7.
6. Read, understand and enforce all safety and use instructions on the slide.
DAILY/WEEKLY MAINTENANCE OF THE VORTEX
1. Periodically inspect the Vortex to assure there are no worn parts and that all
hardware is properly tightened. Replace any hardware which exhibits rust or
corrosion.
FIGURE 1

5
2. All slide components require periodic maintenance. Clean components with a
cotton cloth and a non-abrasive soap and water. Avoid harsh chemicals and
disinfectants.
3. Always read the label instructions on any cleaner carefully before applying it to a
surface.
4. Inspect the plumbing system for leaks. Freeze/Thaw cycles may cause leaks at
plumbing joints which should be repaired prior to use.
5. Check all safety labels to insure they have not peeled or been removed. Contact
S.R. Smith Customer Service (800-824-4397) for replacement labels.
6. The support structure is made from steel, is primed and powder coated with a
high quality acrylic urethane finish. However, corrosion may occur depending on
water chemistry and environmental conditions. Inspect the slide on a semi-
annual basis, sand and repair any surface rust. For touch-up paint (PN # 09-819-
1), contact S.R. Smith Customer Service (800-824-4397).
CAUTION: Because this product is manufactured from Steel, placement on a pool
with a Salt Chlorine Generator will require frequent inspection and maintenance due
to the corrosive nature of these systems with all steel alloys. It is recommended that
all slide components be rinsed daily with fresh water.
APPLICABLE STANDARDS AND CODES
The installation of the VORTEX must comply with all applicable governmental and
building codes.
ASSEMBLY AND INSTALLATION
All S.R. Smith VORTEX slides are inspected prior to shipment from the factory. Proper
assembly and installation is mandatory. Improper assembly and installation voids S.R.
Smith’s warranty and may affect the safety of the user. It is the installer’s responsibility
to ensure that the structural integrity of the concrete pad prior to installation of the slide.
DRAWINGS
All drawings in this Slide Owner’s Manual (Figures 1 through 5) are for illustration
purposes only and are NOT TO SCALE.
SUBSEQUENT OWNERS
The Owner’s Manual must remain with the owner of the slide. If the owner changes, the
Owner’s Manual shall be brought to the attention of the new owner.

6
MANUFACTURER’S PLACEMENT INSTRUCTIONS
PROPER ASSEMBLY, INSTALLATION, USE, AND SUPERVISION IS ESSENTIAL FOR PROPER
OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY OR DEATH.
1. The critical dimensions for placement of the Vortex are as shown in FIGURES 2 and
3.
A. The slide exit runway surface shall not exceed twenty inches (20”) above the
water surface as shown in FIGURE 2.
B. The slide shall be positioned so that all water flowing off the runway exit drops
into the pool. Recommended overhang is (3”) inches.
C. The minimum depth of water below the
exit lip of the slide shall be three feet (3’)
and increases to four feet six inches (4’-
6”) at Pt. A, which is a distance of four
feet six inches (4’-6”) from the exit lip of
the slide as shown in FIGURE 2.
D. A minimum depth of four feet six inches
(4’-6”) shall be maintained at a distance
of nine feet (9’) along the extended
centerline of the slide from Pt. A. as
shown in FIGURE 2.
2. A minimum clearance area in front of the slide shall be
maintained at all times as follows:
A. The minimum clearance distance on either side of the
extended centerline of the slide runway shall not be
less than three feet six inches (3’-6”) at a point no less
than two feet six inches (2’-6”) from the exit lip of the
slide and extending a distance of thirteen feet six
inches (13’-6”) in front of the slide as shown in FIGURE
3.
FIGURE 3
FIGURE 2

7
3. SLIDE PLACEMENT INSTRUCTIONS FOR INSTALLATIONS ON POOLS WITH
OTHER SLIDES AND/OR DIVING BOARDS
A. The minimum clearance area in front of a properly installed diving board on an
inground swimming pool is a minimum distance of three feet six inches (3’-6”) on
either side of the board’s centerline as shown in FIGURE 4. Pt. C extends a
minimum distance of “C” from the tip end of the board as shown in FIGURE 4.
The width distance “W” on either side of Pt. C is given in Chart 1 and shown in
FIGURE 4.
“C” DIMENSION FOR BOARD = AB + BC
“W” DIMENSION FOR BOARD = WIDTH AT PT.C
B. The minimum clearance area of a slide or diving board shall not intersect any
coping or rope and float line as shown in FIGURE 5. The minimum clearance
area of a slide or diving board may intersect each other provided that they are
not used simultaneously.
CHART 1
BOARD MINIMUM CLEARANCE AREA
POOL TYPE
“C” DIMENSION
“W” DIMENSION
I
14’-6”
5’-0”
II
14’-6”
6’-0”
III
16’-6”
6’-0”
IV
18’-6”
7’-6”
V
21’-0”
7’-6”
See Article 5 contained in ANSI/APSP/ICC-5 2011
STANDARD FOR RESIDENTIAL INGROUND SWIMMING
POOLS and refer to FIGURE 3 and Table 1 for Minimum
Water Envelope Dimensions AB, BC and Width at Point C.
For Pool Type VI-IX, see Article 6.6 in ANSI/APSP-1 2003
STANDARD FOR PUBLIC SWIMMING POOLS and refer to
Minimum Dimensions for Diving Portion of Class B and C
Pools.
FIGURE 5
FIGURE 4

8
CLEANING INSTRUCTIONS
Use nonabrasive soap and water when possible. In addition, you may safely use the
below listed products. Always try a test spot before applying to a large area.
Windex ® With Ammonia Formula 409 ® Fantastik ®
Soft Scrub ® Scrubfree Tackle ®
Glass Plus ® Topjob ® Tilex ®
Always read the label instructions on any cleaner carefully before applying it to a
polyethylene surface.
AVOID HARSH CHEMICALS AND DISINFECTANTS. DO NOT USE:
Dow with Scrubbing Bubbles ® Lysol ® Disinfectant Ajax ® Cleanser
Windex ® With Vinegar White Cap ® Ajax ® Liquid
PRODUCT WARRANTY REGISTRATION
Registering your product with S.R. Smith helps us to provide better warranty service
and ensures you get timely information about product updates.
Our product registration process is easy! Scan the QR code below or visit
www.srsmith.com/en/customer-service/product-registration/.
Don’t wait! Register your S.R. Smith product today!