SAFERA Siro User manual

INSTALLATION MANUAL
SAFERA Siro Stove Guard
with Power Control Unit PCU3
V4.2.1 ENG SIRO PCU3

2
CONTENTS
1. Preparations
2. Installation
3. Troubleshooting
4. Optional: Installing the Water Leakage
Sensor
Follow these instructions carefully and
pay particular attention to the instruc-
tions marked in the following way:
ѥWARNING
Follow instructions marked with a warn-
ing accurately to prevent injury to per-
sons and damage to property.
⚐ATTENTION
Follow instructions marked with a note
carefully to prevent damage to property.
ѧHINT
Hints give you useful advices on using the
appliance.
WARNINGS
ѥWARNING
Read user and installation manual before
using or installing the appliance.
Install and check the application accord-
ing to the instructions. SAFERA is not li-
able for any damages or expenses caused
by inappropriate installation.
Check that the Stove Guard is compatible
with the cooker (see section 1.1).
If the network cable is damaged, it must
be replaced by the service personnel of
the manufacturer or their representative
to avoid hazards.
All electrical connections must be carried
out by a qualied electrician.
⚐ATTENTION
If the appliance was stored in a cold
space, it must be allowed to warm up to
room temperature before connecting it to
electric network.

3
1. PREPARATIONS
Check the product and the contents of the
package before installation:
• Central Unit Ⓐ (pre-installed into a
cooker hood)
• Power Supply Ⓓ
• Power Control Unit Ⓒ
• User and Installation Guides
• Declaration of Conformity
ѥWARNING
Please contact your vendor if you notice
anything unusual about the appliance.
Ⓒ
Ⓐ
Ⓓ

4
1.1 Compatibility
SAFERA Stove Guard is compatible with
most electrical cookers, hobs and ovens
meant for household use:
• Traditional cast-iron cookers and hobs
• Ceramic cookers and hobs
• Induction cookers and hobs
• Cookers and hobs equipped with a
timer, afterheat indicator, child proof
lock or integrated switch-off system
SAFERA Siro is compatible with cookers
no wider than 90 cm, see Installation step
1/6.
8
91
3
72
4
5 6
1.2 Central Unit Ⓐ
❶ Child proof lock button
❷ OK button
❸ Indicator light for child proof lock
❹ Indicator light for normal activity
❺ Warning light for cooktop hazard
❻ Warning light for water leakage
❼ Adjustment mode button
❽ Indicator light panels
❾ Sensor

5
Install the cooker hood with Central Unit Ⓐaccording to the dimensions:
⚐ATTENTION
The Central Unit Ⓐis plugged into the
wall socket with its own power supply Ⓓ.
Cooker
width
Installation
Height
Max. 60 cm 45 - 75 cm
60 - 90 cm 60 - 75 cm
Width
Align the Central Unit
±15 mm with the cen-
tre of the cooktop.
Depth
Align the Central Unit
±100 mm with the cen-
tre of the cooktop.
INSTALLATION - STEP 1/6 Mount the Central Unit

6
INSTALLATION - STEP 2/6 Mount the Power Control Unit Ⓒ.
ѥWARNING
Make sure that there is no power supply
to the cooker and the oven by removing
their fuses. Also ensure that the cooker is
switched off.
OUT-wires are always energized when the
power control unit is connected to the elec-
trical network. If a wire is loose, it must be
properly covered.
If the element voltage of the cooker is 400
V, the fuse can only be maximum of 10 A.
If the element is 230 V, the fuse can only be
maximum of 16 A.
Do not install the Power Control Unit to
excessive heat: Operational ambient tem-
perature is +5 … +40°C.
⚐ATTENTION
Power Control Unit requires a neutral
wire to operate.
Install the power control unit Ⓒ so that it
is not exposed to moisture. Check that all
cables can move freely.
Install the Power Control Unit PCU3.
ѧHINT
If you are replacing a cooker, press the
adjustment mode button ❼ for ve sec-
onds until you hear a signal. Continue the
installation according to step 3/6.
OUTIN
PE
L/N
L
PE
N
L
L
230V 16A
400V 10A
230V 16A
400V 10A
230V 16A
400V 10A
MAX
MAX
MAX
L1
L2
L3
MICRO DISCONNECTION
OFF

7
IN
5 x 2,5 mm2
0,7 m
OUT
5 x 2,5 mm2
1,3 m
180 mm
60 mm
130 mm
Optional water sen-
sor connection.
See chapter 4.
Mount the Power Control Unit on the wall behind the cooker or into the cabinet
next to the cooker.
Coupletheprotectiveearthrst(PE).
Couple the other wires.
Don’t reconnect the power to the cooker yet.
Installation
3
4
2
1

8
INSTALLATION - STEP 3/6 Set up the wireless connection
Connect the power supply
Ⓓ: indicator light panels
❽are lit in purple.
Put back the fuses for the
cooker and the oven. The
Power Control Unit Ⓒ will now
contact the Central Unit Ⓐ
whichgivesasoundsignal(•••).
3
Press the adjustment
mode button ❼: indica-
tor light panels ❽start blinking
purple-blue.
2
ѧHINT
You can re-start the installation process
anytime by pressing the adjustment mode
button ❼ for ve seconds until you hear
the signal and continue from step 3/6.
1
ON

9
OpTION 1:
Cooker and oven are connected to
the Power Control Unit Ⓒ.
Turn on the oven and press the child
proof lock button ❶. When
you hear a sound signal
(•••),turnofftheoven.
ⒸⒸ
or
When the indicator light panels ❽start blinking yellow-green, you need to calibrate
the system. Choose from the two options:
Check that the indicator light for normal activity ❹blinkseveryveseconds.
INSTALLATION - STEP 4/6 Calibrate the system
1
2
ѧHINT
With induction cooker, use a compat-
ible dish.
OpTION 2:
Only cooktop is connected to
the Power Control Unit Ⓒ.
Turn on the biggest cooker plate with
maximum power and press
the OK-button ❷. When
you hear a sound signal
(•••),turnoffthecooker.
Ⓒ
or

10
Location of the
Cooker
Installation
Height
Alarm Limit
(1-12)
In a corner 75 cm 6*
65 cm 7
55 cm 8
45 cm 9
Next to a wall 75 cm 5
65 cm 6*
55 cm 7
45 cm 8
In an island 75 cm 4
65 cm 5
55 cm 6*
45 cm 7
Adjust the alarm limit according to the reference table above.
The default alarm limit is 6.
First, go to the adjustment mode:
* Default
INSTALLATION - STEP 5/6 Adjust the alarm limit
2
Check the closest recom-
mended alarm limit from
the reference table on the right.
The range is 1-12:
1 = reacts fastest
12 = reacts slowest
Then, adjust the alarm limit:
Lower the alarm
limit (-1): press the
lock button ❶.
Raise the alarm
limit (+1): press the
OK-button ❷.
12
11
10
9
8
7
6
5
4
3
2
1
= default
1
Press the adjustment
mode button ❼: indicator
light panels ❽ lit white.

11
When you adjust the alarm
limit, the new alarm limit is
indicated as shown in the table
on the right.
3
ѥWARNING
Do not set the alarm limit higher than 9
during the installation.
If the alarm limit is set too high, the appli-
ance may fail to detect a hazardous situ-
ation in time.
ѧHINT
You may check the alarm limit
by pressing the adjustment
mode button ❼twice.
Color of the indica-
tor light panels ❽
Number of
beeps
Alarm Limit
Red
•••••• 12
••••• 11
•••• 10
••• 9
•• 8
•7
Blue
•••••• 6 (default)
••••• 5
•••• 4
••• 3
•• 2
•1

12
INSTALLATION - STEP 6/6 READY!Check-list
Checktheworkingorderoftheapplianceandllintheinstallationchecklist:
ፌAll the burners of the cooker cause a child proof
lock alarm.
ፌThe oven (if connected) causes the child proof lock
alarm. The sound signal is lower than the signal
from the cooker child proof lock.
ፌThe child proof lock turns off the oven and all the
burners.
ፌThe indicator light panels ❽are not lit red after
installation.
ፌThe alarm limit is set according to the cooker loca-
tion (see step 5/6).
_______________________________
Installation date
_______________________________
Installation place
_______________________________
Installer

13
3. INSTALLATION TROUBLESHOOTING
Problem Remedy
Installation is not proceeding as
expected.
You can re-start the installation process anytime
by pressing the adjustment mode button ❼forve
seconds until you hear the signal and continue from
step 3/6.
The central unit Ⓐis not respond-
ing to any button and none of the
indicator lights are lit.
Ensure that the power supply Ⓓis connected cor-
rectly to the wall socket and that the socket has
power.
None of the cooker plates cause a
child proof lock alarm.
The wireless connection has not been properly
made: redo the installation starting from step 3/6.
The appliance turns off the power
from the cooker, but the power
comes back on immediately.
Make sure that the Power Control Unit Ⓒis con-
nected correctly – in other words, the cooker is
connected to the OUT cable.
If the light panels ❽are constant-
ly lit red after the installation, the
appliance is faulty:
Press the OK but-
ton ❷tondoutthe
problem type by the
indicator lights (see
on the right).
Blinks once:
Problem with the radio connection
to the Power Control Unit Ⓒ.
Blinks twice:
Power Control Unit Ⓒmalfunction.
Blinks three times:
Power Control Unit Ⓒoverheated.
Blinks once:
Sensor ➒malfunction.
Blinks three times:
Power supply Ⓓmalfunction.

14
4. INSTALLING THE WATER LEAKAGE SENSOR
(optional)
Stove Guard can be equipped with max.
four SAFERA Water Leakage Sensors. The
sensors are placed in the typical leakage
areas, e.g. under the dishwasher or sink.
Attach the sensors Ⓕin place.
Attach the plug Ⓖ of the leakage
sensor to the Power Control Unit Ⓗ.
If there is an extra sensor, its plug Ⓖ
is connected to the connector Ⓘof
the previous sensor.
Check the operation of the furthest
sensor Ⓕby placing a damp paper
towel against it for 15 seconds. When
the water is detected, the Central Unit Ⓐ
gives a sound signal, the warning light for
water leakage ❻blinks and light panels ❽
blink blue.
Reset the leakage alarm by pressing
the OK button ❷. Clean and dry the
sensor.
1
2
3
4
5
ѧHINT
If the sensor is left wet, the appliance will
give another alarm in an hour after sign-
ing off the previous one.
C
GH
I
F

15