Samsung 5 Series User manual

Step 5: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTER
E button.
To skip a screen, press the MENU button. To turn on your TV, press the POWER
button on the remote or on the TV. To run Plug & Play, follow these steps:
1 Using your remote control,
select the language for the On
Screen Display (OSD), and then
press the ENTER E button.
Plug & Play
2 Select Home Use, and then
press the ENTER E button. If
you select Store Demo, the TV
will reset your picture and audio
settings every 30 minutes.
3 Select the Antenna Source
to memorize. you must select
Antenna Source to same type
as your cable system type. After
selecting source, select Start;
then press the ENTER E
button on your remote.
✎ Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎ If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4 The TV memorizes the available
channels. This process can take
up to 45 minutes.
5 A fter the TV has memorized the
channels, choose the Clock Mode.
Select Auto if you have a digital
channel in your area. Select Manual
if you don’t, or if you have a cable or
satellite box. When done, press the
ENTER E button.
✎ If you select Manual,
the clock setting screen
appears.
6 Select the daylight savings time
setting: Off or On and then
press the ENTER E button.
7 Select the time zone in which you live, and then press ENTER E .
8 After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9 The Enjoy your TV. screen appears. Then press the ENTER E button.
If You Want to Rerun Plug & Play
1. Press the SOURCE button on your remote, then select TV mode.
2. Press the MENU button on your remote to display the menu.
3. Press the ▲ or ▼ button to select Setup, and then press the ENTER
E
button.
4. Press ENTER
E again to select Plug & Play.
Step 1: Install the Stand
Follow the steps below to connect the TV to the stand.
✎ NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the LCD TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the LCD TV placed down, it may lean to one side.
1 Connect the Guide Stand to the
Stand using four screws
(M4 X L12) as shown.
2 With your TV upright, connect
the TV to the Stand as shown.
3 Fasten the two screws (M4 X L12) at
position 1, and then fasten the two
screws (M4 X L12) at position 2.
ss
ss
1
2
Step 2: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the right.
2. Install two AAA batteries.
✎ Make sure to match the + and -
ends of the batteries to the diagram
in the battery compartment.
3. Replace the cover.
Step 3: Connect Power and Antenna or Cable
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12
AM EST.
To register this product, visit: www.samsung.com/
register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
Step 4: Connect External Devices
Connecting an AV device (DVD/ Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
L Move E Enter
Select ‘Home Use’ when installing this TV in your home.
Store Demo Home Use
Plug & Play
U Move E Enter m Skip
Select the Antenna source to memorize.
Air
Cable
Auto
Start
Start
Start
Plug & Play
U Move E Enter m Skip
Set the Clock Mode.
Clock Mode Auto
Manual
Plug & Play
U Move E Enter
Select Language of the OSD.
Language
English
Español
Français
Plug & Play
48%
E Enter m Skip
Auto Program in Progress.
DTV Air : -- Air : --
DTV Cable : -- Cable : -- Cable : 35
Stop
Plug & Play
AUDIO OUT
PC OUT
DVI OUT
AUDIO OUT
HD connection
Using an HDMI to DVI Cable
Using a D-Sub Cable
HDMI to DVI Cable (Not Supplied)
D-Sub Cable (Not Supplied)
Audio Cable (Not Supplied)
Audio Cable (Not Supplied)
OPTICAL
Digital Audio connection
Using an Optical Cable
Optical Cable (Not Supplied)
Digital Audio System
AUDIO OUT
VIDEO OUT
AUDIO OUT
COMPONENT OUT
AUDIO OUT DVI OUT
HDMI OUT
Lowest Quality Connection
Using an Audio/Video Cable
Audio/Video connection (480i only)
Using an HDMI to DVI Cable
HD connection (up to 720p/1080i)
Very Good Connection
Device
Using a Component Cable
Good Connection
Component connection (up to 720p/1080i)
DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB)
DVD, Blu-ray player, cable box, STB satellite receiver, VCR
Best Connection
HD connection (up to 720p/1080i)
Using an HDMI Cable
DVD / Blu-ray player / HD Cable Box / HD STB
(Set-Top-Box) satellite receiver
Device
Device
Device
Audio Cable (Not Supplied)
Video Cable (Not Supplied)
Component Cable (Not Supplied)
Audio Cable (Not Supplied)
Audio Cable
(Not Supplied)
HDMI to DVI Cable
(Not Supplied)
HDMI Cable
(Not Supplied)
VHF/UHF Antenna
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
• Cable or Satellite box
Ant or Cable Out
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Best to use 75 ohm (round) cable.
or
Antenna Cable (Not Supplied)
Top view
Front
Rear
Rear
Screws (M4 X L12)
Guide Stand
Stand
ss
ss
Rear
Front
BN68-03220A-00
U Move E Enter m Skip
Set to daylight saving time.
DST
Plug & Play
Off
On
[LC500-QSG]BN68-03220A-00Eng.indd 1 2010-09-17 오후 1:39:36

Step 6: Remote Control
Remote Control Buttons and Functions
Selecting a Source
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
input. Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or through
the Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component, or
Composite jack, press the SOURCE button on your remote. Each time you press
the SOURCE button, you change to a different source.
Viewing the On Screen Menus
To view the On Screen Menus, follow these steps:
1. With the power on, press the MENU button on
your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel, Setup, Input, Application, and Support.
2. Press the ▲ or ▼ button on your remote to select a menu option, and then
press the ENTER
E button.
3. When done using the menu, press the EXIT button on your remote to exit.
Changing the Picture Mode
Your TV has three preset Picture modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
The Picture modes are listed and described in the table below:
Mode Description
Dynamic Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
Standard For a bright, detailed picture in a normally lit room.
Movie For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture mode, follow these steps:
1. With the TV on, press the MENU button on your remote, then select Picture.
2. Select Mode, the Press the ENTER
E button.
3. On the Mode menu in Picture, use the ▼ or ▲ on your remote to select the
picture mode you want.
4. Press the ENTER
E button to finish the change.
MTS CCP.SIZE
A B C D
MTS CCP.SIZE
A B C D
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the P.SIZE button on your remote. The first time
you press it, your TV displays the current setting. Thereafter, each time you press
the P.SIZE button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen 4:3 Standard screen Wide Fit
Zoom 1 Zoom 2 Screen Fit
✎ Screen Fit: Displays the full image without any cut-off when HDMI (720p /
1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
Changing Channels and Adjusting the Volume
Adjust the volume by pressing the Volume button
on the remote.
MTS CCP.SIZE
A B C D
Change the channels by pressing the Channel button on the remote.
✎ If your TV is attached to a cable or satellite box, change the channel using
the box’s remote.
✎ You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button.
Connecting a USB Device for Media Play
You can enjoy photo and
music files stored on a USB
device by connecting it to the
TV and using the Media Play
feature. To connect a USB
device for Media Play, follow
these steps:
1. Turn on your TV.
2. Connect a USB device
containing photo or music
files to the USB jack on the rear of the TV.
3. When the Input selection screen is displayed, press the r button to select
Media Play (USB), then press the ENTER
E button.
Photo
Photo Music Setup
SUM
307.2MB/973.7MB
L Move E Enter R Return
Setting the Clock
Before you can use your TV’s On/Off Timer, you must set the clock. To set the
clock, follow these steps:
1. Turn on your TV, press the MENU button on your remote, then select Setup →
Time.
2. Select Clock Mode, and then press the ENTER
E button.
3. Choose Auto or Manual.
x
If you select Auto, set the current time automatically using the time from
digital broadcast.
x
If you select Manual, you can set the Month, Day, Year, Hour, Minute
and am/pm directly by pressing up, down, left and right arrow button on
your remote.
4. Press the RETURN button on your remote when done.
MTS CCP.SIZE
A B C D
Turns the TV on and off.
Returns to the previous channel.
Changes channels.
Displays and selects the available video
sources.
Displays information on the TV screen.
Displays Favorite Channel Lists on the screen.
Displays the channel list on the screen.
Selects the on-screen menu items and changes
the values seen on the menu.
Exits the menu.
MTS: Press to choose stereo, mono or
Separate Audio Program (SAP broadcast).
P.SIZE: Selects the picture size.
CC: Controls the caption decoder.
Press to directly access channels.
Press to select additional channels (digital)
being broadcasted by the same station. For
example, to select channel “54-3”, press “54”,
then press “–” and “3”.
Adjusts the volume.
Brings up the OSD.
Quickly select frequently used functions.
Displays Media Play (USB).
Returns to the previous menu.
Buttons used in the Channel List, Media Play
(USB) menu, etc.
Cuts off the sound temporarily.
[LC500-QSG]BN68-03220A-00Eng.indd 2 2010-09-17 오후 1:39:37